Search dance music

Notes: A-180-9 is another simple but useful tool. It can be used to connect up to 14 signals between different cases by means of standard network cables (RJ45). These cables are available all over world smoothly in different lengths and colours. From the factory two black network cables with 0.5 m length are enclosed.

The upper network connector is wired to the eight sockets 1-8, the lower to the six sockets A-F. That way it's possible to pre-patch different cases and connect signals, that are required in all cases (e.g. clock, start/stop, master CV) by means of one or two cables only instead of 14 individual patch cables. When only eight signals are required only the upper network connector is required and the sockets 1-8 are used. When more than eight signals have to be patched both network connectors have to be used. It's also possible to wire the upper and lower network to different cases (i.e. signals 1-8 to external case #1 and signals A-F to external case#2).

The module is fully passive (no power supply required) and simply wires the 14 sockets to 14 pins of the network connectors.

The A-180-9 comes in pairs for combining two modular systems.

Notes: Module A-147-2 is the successor of the VCLFO A-147 but offers much more features than the predecessor. The module is made of these sub-units:

- VCLFO: voltage controlled low frequency oscillator
- VCA: voltage controlled amplifier, switchable to voltage controlled polarizer
- VC delay unit: voltage controlled linear attack envelope (only one parameter: attack) for delayed LFO operation in combination with the VCA (e.g. delayed vibrato/tremolo)

LFO: The voltage controlled LFO has the waveforms Triangle, Sine, Sawtooth and Rectangle available and features a Reset/Sync input. Triangle/Sine and Rectangle are displayed by means of dual-colour LEDs (probably red/green), Sawtooth has a unicolor LED available (probably blue). The output levels are about -4V...+4V for Triangle, Sine and Rectangle. The Sawtooth level is about 0...+8V.

The CV control can be switched to attenuator or polarizer ("CV Mode" switch). In polarizer mode the CV inputs affects the frequency in the reverse manner when the CV control is left from the centre position. In the centre position CV has no effect and right from the centre the control works like a normal attenuator. The frequency range (without external CV) is from about 0,005 Hz (i.e. about 3 minutes per period) to 200 Hz (with external CV max. frequency about 1kHz). In addition a ultra-low mode can be activated by means of an internal jumper. When the ultra-low jumper is set a fixed voltage is connected to the switching contact of the "LFO CV" socket. In polarizer mode of the CV control that way extremely low frequencies (up to one hour period and more) are possible. For this a jumper has to be installed on the pin header JP6. In the factory a dummy jumper is installed on the pin header JP7 "Dummy". JP7 has no function and is used only for "parking" of the jumper. Simply remove the jumper from JP7 and plug it on JP6. JP6 is located behind the CV control.

VCA: This is a linear VCA that can be switched to "normal" VCA (i.e. kind of a voltage controlled attenuator) or voltage controlled polarizer ("VCA Mode" switch). In the "normal" VCA mode amplification +1 is achieved with about +5V control voltage. In polarizer mode the amplification ranges from about -0.5 (i.e. inverted signal with about 50% level) with 0V CV to +0.5 (i.e. non-inverted signal with about 50% level) with +5V CV. With about +2.5V CV the signal is suppressed. Details about the functioning of a voltage controlled polarizer can be found in the description of the module A-133. In this mode the VCA can be treated also a DC coupled ring modulator (similar to A-114).

The VCA of the A-147-2 has three sockets available: "In" (signal input), "Out" (signal output) and "CV" (control voltage input).

The Triangle Output of the LFO is normalled to the VCA signal input by means of the switching contact of the "VCA In" socket. If another LFO waveform (or any other signal) should be processed by the VCA the corresponding signal has to be patched to the "VCA In" socket. The VCA can be used also independently from the LFO and the Delay CV. In this case the VCA sockets In, Out and CV have to be patched accordingly. The VCA can be used also as waveshaper for the LFO signals (e.g. by patching VCA In and VCA CV to different LFO signals, if necessary via attenuator A-183-1 or offset generator/attenuator A-183-2).

Attack/Delay: The third sub-unit of the module is a simple, voltage controlled envelope generator that has only the parameter "Delay" (or Attack) available. This unit generates a linear increasing voltage that starts from 0V after each Delay Reset until it reaches about +5V. Then the voltage remains at +5V until the next Delay Reset occurs. The inclination or gradient is controlled by the manual Delay control and the Delay control voltage ("Delay CV" input). The waveform is linear, the control scale is exponential. The output voltage is displayed by a green LED and available at the "Delay Out" socket.

The manual Delay control ranges - without external "Delay CV" - from about 5ms (fully CW) up to 2 minutes (fully CCW). By means of an external voltage applied to the "Delay CV" socket this range can be extended. A rising CV shortens the delay time (behaviour like a VCO)!

The Delay output voltage ranges from about 0V to +5V. The rising edge of the gate, clock or trigger signal applied to the "Delay Reset" sockets resets the Delay output voltage to 0 V.

"Delay Out" is normalled to the VCA CV input by means of the switching contact of the "VCA CV" socket and consequently controls the Triangle level provided that no other patch is made. A typical example is the usage of a Gate signal (e.g. from a USB/Midi-to-CV/Gate interface) as Delay Reset. That way a delayed vibrato or tremolo can be realized if the VCA output is patched to the frequency CV input of a VCO (or VCF), or the CV input of a VCA.

Notes: Unlock the potential of the Quad LFO with the LFO Phase Expander. Each expander gives you three outputs that duplicate the LFO with a fixed phase difference. The first ranges from 0- to 180-, the second from 90- to 270-, and the last from 180- to 360-. Along with the original output, this gives you four phases of modulation. These are easily tuneable to quadrature (all knobs centred), but also any arbitrary phase relationship. You can attach up to four expanders, one for each LFO, giving you up to sixteen modulation sources.

A multiphase LFO is extremely useful for building rhythmic modulations, particularly when paired with analogue logic, such as provided by Babel. Further, regardless of the waveform selected on the Quad LFO, the output of the Phase Expander is always a sine wave. This gives you the useful possibility of having three rhythmically related phases of an LFO synced to a clock signal.

Other than rhythmic modulations, the most common use of a multiphase sine LFO is in creating panning and crossfade controls that sound correct using only one or more VCAs. This is useful in panning sounds back and forth, rotating a sound in quadraphonic space, creating Shepard tones, etc.

Even when you don't have a specific need for exact phase relationships, a multiphase LFO gives you a convenient way to expand your palette of potential modulators, adding three related but distinct waves.

Specs

Size: 6HP
Depth: 22mm
Power Consumption: +12V 21mA, -12V 21mA
Output Swing: -5V - +5V peak
Output Impedance: 1kO
Output Drive: 2kO (min), 20kO+ (ideal)

Notes: WarpEx is an expander module that adds polyphony and MIDI to Warp.

- 4-Voice polyphony
- MIDI input and MIDI Thru
- MPE compatibility (MIDI polyphonic expression)
- Dedicated trigger and V/Oct inputs for each voice
- Illuminated pushbutton to quickly toggle between the MIDI voice modes: Mono, Poly and MPE.

Inputs:

- +/- 8 Volts (V/OCT)
- 0.0 Volts to +5.0 Volts (TRIG and MIDI)
- Overvoltage protection on all jacks.
- 4 TRIG Inputs: Gate inputs for Voices 1-4
- 4 V/Oct Inputs: CV input for pitch of voices 1-4 (i 8V, up to low audio rate ~100Hz)
- 1 MIDI In: Input Type-A for Midi signals. Use provided MIDI-to-DIN adapters.
- Button Toggles between MIDI voice modes: Red = Mono, Blue = Poly, Purple = MPE (Poly)

Outputs:

- Midi-Thru, 5v signal

WarpEx is fully managed by the Warp master

Scope of delivery:

Module, 3mm screws, ribbon cable for connection to Warp, 2 Midi-to-Din adapters Type A

Power consumption: Warp powers this expander via the included grey bus cable
Depth: 30mm
HP : 4

Notes: The New Systems Instruments VCA module gives you four well-calibrated VCAs in 6HP. These VCAs use operational transconductance amplifiers (OTAs) at their core, for true linear operation. However, unlike most OTA VCAs, the New Systems VCA is extremely low noise and distortion, coming in at < 0.2%, with ~0.05% typical.

There's no such thing as "transparent," particularly in synthesis, where the concept of an original signal that could be faithfully reproduced is often altogether absent. In a VCA in particular, a desirable envelope response can be even more important than accurate reproduction of the input at some fixed level.

The New Systems Instruments VCA has an extremely neutral, open sound. The envelope response sounds noticeably fast and accurate. If you want a dirtier VCA, stay tuned. New Systems are in the process of designing a different VCA with some control over signal and envelope linearity.

Specs

Size: 6HP
Depth: 22mm
Power Consumption: +12V 25mA / -12V 25mA
THD+N at 1kHz: 0.2% (max), ~0.05% (typical)
Output Swing: -10V - +10V peak
Input Range: -10V - +10V peak
CV Unity: 5V
Input Impedance: 85kO
Output Impedance: 150O
Output Drive: 2kO (min), 20kO+ (ideal)

Notes: Expandoor

The Expandoor gets you quickly and simply using AMP's Melody Oracle, Star Song, or Touch Tones (as well as other possible future devices) as a CV and Gate controller. It outputs Eurorack-compatible CV and GATE signals, transforming your AMP device into a versatile and novel modular synth sequencer or controller. The Expandoor can be used as a standalone tabletop box, or mounted in a 3U 10HP rack space.

Three independent GATE outputs:

Just as the three "Register" zones on your AMP device gate the audio for the three octaves of the built-in synthesizer, there are three corresponding gate outputs on the Expandoor. The 1/8" jacks labelled "BS" "LH" and "RH" output ~11V DC gate signals whenever those zones are gating "ON" on your AMP device.

CV output, tuners and LED indicators:

The jack labelled "CV" outputs a tuned set of CV values (0-11V), tuned independently but correspondingly, to the set of tuners on your AMP device. The row of multi-turn tuners on the front panel allow fine tuning of each CV state. One tuner is active at a time, depending on the state of the "INTERVAL" zones on your AMP device. The active tuner is conveniently indicated in real time via lights found to the right of the tuners. The indicator lights serve a second function of showing you which tuner on the controlling AMP device is also active in parallel.

AMP LINK jacks

The AMP LINK jack on the bottom left of the front panel (with the arrow pointing IN) connects your controlling AMP device into the EXPANDOOR. Use only shielded CAT 5 or CAT 6 cables and connectors (the correct cables will have metal end connectors). The AMP LINK jack on the right outputs a signal identical to the input, allowing chaining of multiple Expandoors and/or Wave Expanders. Do not plug more than one AMP controlling device into a single Expandoor simultaneously, or damage to the devices could occur.

Each controlling device requires its own Expandoor or Wave Exapnder, but multiple expansion modules can be chained from one controlling device. One potential benefit to chaining expansion modules is the ability to output multiple tuned, corresponding but independent, CV channels. Meaning multiple sets of harmonic values could be tuned and accessed at the command of the single controlling AMP device, or accessed via other modules in your system.

Tech specs:

Input: AMP LINK via shielded CAT5 or CAT6 cable
Power: 12V DC Supplied via AMP LINK
Outputs: 3 Gate (~11V unipolar), 1 CV (variable 0-11V unipolar)
Tuners: 8 multi-turn fine tuners for CV, with indicator lights
Size: 3U 10HP (approximately 5.25" H x 2" W x 1.5" D)

Notes: You've been up all night in a bidding war on eBay to win a prized 80s rack effect unit - you can't wait to add some serious cheese to your tracks, and the sound of gated reverbs ring in your ears. Your heart pounds, and your pulse rises to crescendo as you win the auction! But there is one problem: your Eurorack system runs way too hot to simply plug straight into your stereo FX units. Your heart sinks, as you realize there is not much you can do that doesn't involve a lot of messing around with complicated and weird mono modules. That is, until now: introducing the Herzlich SFXI.

The Stereo FX Integrator was designed in response to my own need: owning several cool stereo FX units, and having no easy way to integrate them with an easy send and return, in my Eurorack system. Attenuate your Eurorack signals down to line level, or even all the way down to instrument level, and get a nice, clean boost back up to modular levels, with this dead simple and highly useful device from the R&D department at Herzlich Labs.

You can even use it to integrate external stereo line level signals into your Eurorack, which is both nice and convenient, and also useful. Finally, you have an easy way to get the sound of your JV1080 into your Clouds.

The scientists have been working overtime to produce this unit, and were fed extra rations of maize and millet gruel just to bring you this circuit. Every SFXI sold will grant the poor souls at Herzlich Labs another serving of maize and millet gruel. Please think of the poor scientists at Herzlich Labs.

Dimensions
4 HP

Current Draw
30 mA +12V
30 mA -12V
0 mA 5V

Notes: Pluck is a physical modelling synth voice. It uses the Karplus-Strong algorithm to create plucked string sounds. The dampening control sets the size of the string and allows for dramatic timbral shifts.

The decay control changes note length from percussive transients to infinite harp sounds. In addition, four voice polyphony provides complex layered tones; all from a single sound source.

Strum a new chord with Pluck.

Notes: The "Luskellader Frekans Izel" is a Low Frequency Oscillator (LFO) that can be used to modulate various parameters of the synthesizer, including pitch, filter cutoff, and amplitude. The module has 2 ouputs, with continuous morphing shapes available at the same time, one Square/PWM, one Saw/triangle/inverted saw. The LFO has a speed switch going from low to audio rates. The 2 knobs are : Speed and Morph. The module is 6HP wide and is made with quality components such as Nichicon/Panasonic caps and alpha pots.

HP : 6

Notes: Shapes is a wide ranging and fully analogue oscillator which can perform duties as both auxilliary VCO* as well as VC-LFO. Shapes can be configured to cycle continuously, or to provide one-shot shaped outputs. When set to one-shot mode, Shapes may be used as an ersatz envelope generator.

Using the Time knob, Shapes can cycle from as low as 8 seconds (whale song) to as high as 19500Hz (bat beeps).

Shapes has 3 simultaneous outputs:

sawtooth (+/-5V, 10Vpp)
ramp (+/-5V, 10Vpp)
triangle (+/-5V, 10Vpp)
Additional waveforms may be derived courtesy of the Shape knob. Anticlockwise from 0 achieves progressively logarithmic sawtooths and ramps, whereas clockwise from 0 achieves progressively exponential sawtooths and ramps. The effect of the Shape knob on the triangle waveform is asymmetric, anticlockwise from 0 achieves progressively logarithmic leading edge, whereas clockwise from 0 achieves progressively exponential falling edge. Progressively exponential triangle waveforms can be achieved using the Time CV knob (set Shape knob to 0) providing there is no jack in the Time CV input socket

Time CV input provides wide ranging control of time. It is possible to dial in something approaching 1V/oct over a limited range, although Shapes has not been designed to perform as an accurately tracking VCO. In the audio range, Shapes comes into its own when used as a 'daughter' VCO to an external 'mother' VCO by patching the 'mother' VCO into Shapes' Gate In input socket - some impressive oscillator sync style effects can be achieved.

Gate In can also be used to initiate waveforms in one-shot mode, where a pulse of any length will cause Shapes to complete one cycle.

*Shapes has not been designed to perform as an accurately tracking audio VCO.

Product Specifications

12V draw: 15mA
5V draw: 0mA
-12V draw: 15mA
Depth: 45mm
Width: 4HP

Notes: The Morphor LFO - Dual is a slim (6 HP) dual LFO. Each channel features analogue triangle, square, sine, saw and inverted saw outputs and a cycle reset input.

Frequency ranges:

Low: 0.005 - 1.5 Hz
Med: 1.5 - 425 Hz
High: 15 - 4250 Hz

Features

100% analogue
Dual channel
Triangle wave output
Square wave output
Sine wave output
Saw output
Inverted saw output
Cycle reset input
Low/Med/High frequency selector

Specifications

Panel width: 6 HP
Panel height: 3 U
Module depth: 25 mm
Current draw: 12 V : 22 mA | -12 V : 22 mA | +5 V : 0 mA
Dimensions: 128.5 x 30.3 x 25 mm
Weight: 71 g
Power Socket : 10-pin

Notes: The Morphor Envelope - Dual ADSR is a slim (6 HP) dual envelope generator. Each channel features standard ADSR (Attack, Decay, Sustain, Release) analogue circuitry, providing the classic, rich envelope shaping tools essential for any modular enthusiast. It features separate control knobs for the attack, decay, sustain and release parameters, two independent channels for versatile envelope shaping and each channel comes equipped with gate, re-trigger, output, and an inverted output.

On the back of the module you can find tiny switches for each channel to change the overall length of the complete envelope:
Short: 5 ms - 30 s
Med: 25 ms - 60 s
Long: 60 ms - 200 s (=3.3 min)

Features

100% analogue
Dual channel
Attack length control
Decay length control
Sustain level control
Release length control
Inverted output
Re-trigger

Specifications

Panel width: 6 HP
Panel height: 3 U
Module depth: 40 mm
Current draw: 12 V : 32 mA | -12 V : 32 mA | +5 V : 0 mA
Dimensions: 128.5 x 30.3 x 40 mm
Weight: 111 g
Power Socket : 16-pin

Notes: This is a self contained analogue high hat module. This is a Transistor based VCA design. It is influenced by the DR110 drum machine. The original circuit used 4 oscillators to make the metallic audio sound. I added the original 4 oscillator, and an extra 6 oscillator circuit. The 6 oscillator version is doing a double XOR ringmod (internally). You select that by switch.

The 4 oscillator design sounds more crunchy, where as the 6 XOR circuit sounds more polished with sheen. You can blend in the amount of white noise in the mix labeled 'sizzle'.

Internally, the audio is passing through a few high pass filters, making the output sound very high in frequencies.

The module by itself is not exciting. But in the mix, with other percussion modules, this is your favorite-go-to module. It sits almost perfect in the mix.

There are two triggers. One is for 'Open' sound. The other is for 'close' sound. Both open and close have there own decay knob to adjust the length of the audio tail.

There is a tone control, labeled LPF. Use this to taper off some of the high frequencies.

Instead of adding an 'accent' control. Both triggers have been made to voltage variable. 5V triggering is the normal expected input. So a 3V trigger will sound softer in volume. 10V trigger signals will sound louder.

This module is as simple as it gets, just patch your Arturia Beat Step Pro and use the drum track.

Features

-Both trigger inputs are voltage variable. You can get softer audio, with softer trigger voltage.
-2 voice metallic noise generator
-2 decays (open and close)
-2 Flavors select by switch.
-Normal mode, and Sustain mode, selected by switch.
-frequency adjustment of the internal XOR ringmod.
-classic roland sounding transistor based VCA.

Why get this module over the Shimm module, or other high hats modules?

-Ease of use, ready to go. No sound exploring needed.
-Want the classic transistor based, crunchy sound.
-lower budget
-Sits very well in the drum mix.

Dimensions
8 HP
32 mm deep

Current Draw
21 mA +12V
13 mA -12V

Notes: Expander module adds four more assignable CV inputs to Squid Salmple for advanced modulation and sample manipulation. A must for all Squid Salmple owners.

Supplier's Notes:
AXON-1 is a 4HP expander module for the SQUID SALMPLE that provides 4 additional freely assignable CV inputs.

The addition of AXON-1 brings Squid's total number of CV inputs to 7, greatly increasing the possibilities for vast modular sample manipulation.

Each modulation assignment includes digital attenuation and offset and behaves just like Squid's 3 built in CV inputs.

AXON-1 requires firmware 166 or later installed on the Squid Salmple to function!

Notes: The mmMidi is a simple & compact MIDI to CV interface for your Eurorack synthesiser. It translates both MIDI clock and 2 Channels of MIDI note, velocity and gate information to corresponding voltage control signals. The mmMidi is quick to set up and requires minimal configuration.

Notes: Designed with and for performing artists, Switch 4 delivers a hands-on signal switching and routing solution for your Eurorack modular synthesiser.

Quickly mute audio signals, trigger envelopes live, select modulation sources on the fly... With custom dual-action toggle switches, an intuitive interface and sturdy construction, Switch 4 will prove just as useful on stage as in the studio.

The bottom switching section includes four lever-actuated toggle switches, to make or break the signal path between the inputs and outputs. These switches feature a dual action: latched upwards, momentary downwards.

The four input signals are also sent to the top routing section, where two rotary switches allow you to select the signals to be sent to the matching outputs. Here you'll also find dual-action toggle switches, for added versatility.

Finally, all signal paths are buffered, avoiding signal cuts when shorting a jack during patching or severe loading effects when driving many inputs. The high-end components provide exceptionally low noise and distortion, so Switch 4 can reliably process audio, control voltages and gates/triggers.

Notes: 'Beast's Chalkboard' is dual channel stepped voltage source and adder for your eurorack modular synthesizer system. It primarily is intended as a dual octave switcher for VCO's but has many other uses including sequence transposition, FM ratio creation, buffered CV distribution and VCO calibration.

Technical Specifications:

Supply: +/-12V (Reverse voltage & polyfuse protection)
Current Draw: ~30ma
Size: 6 HP
Depth: 22mm (including power header)
Offset Error: +/- 10mV

Notes: Module A-105-2V is a voltage controlled low pass filter with 24dB/octave slope.

It is the successor of the A-105 which had to be discontinued because the obsolete SSM2044 filter circuit. The A-105-2 is based on the SSI2144 which is in turn the successor circuit of the SSM2044. The features of both modules are nearly the same. The main difference is the clearly reduced front panel width of the A-105-2 (4HP instead of 8HP) and the associated changes of the controls and sockets positions. In addition the A-105-2 is equipped with 2 audio inputs.

The module has these controls and in/outputs available:

Control Frequ: manual frequency control
Control FCV2: attenuator for the frequency control voltage applied to socket FCV2
Control Q: manual resonance control
Control QCV: attenuator for the resonance control voltage applied to socket QCV
Control Input 1 Level: attenuator for the audio input signal applied to socket Input 1
Socket Input 1: audio input 1 (with attenuator)
Socket Input 2: audio input 2 (without attenuator)
Socket FCV1: frequency control voltage 1 (without attenuator, about 1V/oct scale)
Socket FCV2: frequency control voltage 2 (with attenuator)
Socket QCV: resonance control voltage (with attenuator)
Socket Out: audio output
Technical notes:

Frequency range: about 15Hz ... 15 kHz
Resonance up to self oscillation
Max. input voltage at Input 2 without clipping/distortion: about 15Vpp
Max. output voltage without clipping/distortion: about 15Vpp
The signals of both inputs are mixed before they are processed by the filter. This saves an external mixer for small setups.
Depth: 45 mm

HP : 4

Notes: Incredible sounding VCO module that helps you get incredibly rich signals out of your synthesizer. The Dreadbox Hysteria VCO features a huge frequency range of 16hZ to 32kHz. This gives you a lot of functional pitch to work with, allowing you to explore the sounds capable from this module.

The sounds themselves rest on a variable waveform selector - meaning you can scroll through the waveforms and blend them together. This can even be CV controlled, so you can obtain an evolving sound that changes over time. The modules in the Chromatic series give you a great starting point in the world of modular synths and are a must-have for beginners and professionals alike.

Power Consumption: 114mA @ +12V , 46mA @ -12V
10HP
35 mm deep

Notes: VCA 3X is a simple yet great solution for synth users looking to add more VCAs to their setup in a single and compact module. This module features 3 VCAs with individual Signal and CV inputs and outputs.

Notes: The 8S is an 8 step sequencer in 8 HP with control over some parameters of the sequence as reset, hold, random step and direction. The inputs have been designed to work with clock related signals like triggers or gates but any type of CV signal can be used. The output signal path is completely analog and its range can be set to unipolar (0 to +5 volts) or bipolar (-5 to +5 volts) via jumper on the back of the module.

Technical specifications:

8HP

38 mm depth

Consumption: +12V: 25mA ; -12V: 5mA

Notes: The CubuSynth ADSR Module is a VC looping envelope generator, with controls for the Attack, Decay, Sustain and Release stages, for overall Time of the envelope and CV inputs for Time and Level.

The EnvGen8 chip was written/designed by Tom Wiltshire aka "Electric Druid".

1 ATTACK (1ms - 10s)
Sets the time, the Envelope takes to reach full level from the moment a gate is detected (Key is pressed)
2 DECAY (1ms - 10s)
Sets the time, after the envelope hits full level, to fade to the level set by the SUSTAIN Knob.
3 SUSTAIN (0% - 100%)
Sets the Volume to stay after the decay, while the GATE input is high.
4 RELEASE (1ms - 10s)
Sets the time for the fade out on falling edge of the GATE input (after the Key is released)
5 MODE switch
Select between exponential and linear curves.
6 PUNCH switch
Adds extra thump to very short percussive envelopes
7 LOOPING MODE switch
Allows selection between three different modes of operation. Gated mode is a normal envelope. Gated Looping will
trigger the ATTACK stage when the GATE goes high, then continue looping whilst the GATE remains high, and will
RELEASE to zero when the GATE goes low. The LFO Looping mode loops continuously and ignores input from the
GATE.
8 TIME (x1 - x100)
Overall Time control which shortens the length of the entire envelope.
9 TIME CV Attenuator
Attenuates incoming CV for Time modulation. Higher voltages will shorten the
length of the envelope.
10 TRIG Input
Re-trigger for the envelope. Useful for Polyphonic patches. Envelope goes to
ATTACK stage on rising edge of 0-5V pulse while Gate can still be on.
11 GATE Input
Normalized to TRIG Input. Envelope goes to RELEASE stage on the falling edge.
12 Level CV Input
Control the overall Volume of the envelope. Can be used for velocity control.
If nothing is plugged in, the Volume stays on max.
13 OUT
CV-output of the envelope (0 to +5V)
14 LED
Indicates the output voltage.
15 TIME CV
CV Input for Time modulation. Higher voltages will shorten the length of the
envelope.
16 INV. OUT
Inverted voltage of the output CV (0 to -5V)

Dimensions
10 HP
25 mm deep

Current Draw
16 mA +12V
16 mA -12V
7 mA 5V

Notes: Module A-160-5 is a voltage controlled clock multiplier. The incoming clock signal (socket Clock In) is multiplied by a factor that depends upon the control voltage on socket CV In (0...+5V) and the position of the Mode switch. The multiplied clock signal is available at the socket Clock Out. According to the position of the Mode switch different clock multiplying factors are assigned to the control voltage. With 0V CV no clock output is generated. This state is indicated by "all LEDs off". With increasing CV integer factors (left position of the mode switch), power of two factors (middle position) or a mix of both (right position) are obtained. Nine LEDs are used to show the currently selected multiplying factor. In addition two LEDs are used to display the incoming and outgoing clock signal.

A manual control is used to adjust the clock multiplication factor manually without the need of an external control voltage. The voltage generated by this control ("Manual") is normalled to the CV In socket. As long as no plug is inserted into the CV In socket the clock multiplication factor is adjusted by means of the manual control knob and displayed by the LEDs. For dynamic applications (like the ratcheting function described below) the manually generated CV is overwritten by the external CV which has to be fed into the CV In socket.

The module can be used for all kind of clock multiplying applications. One important example is the generation of so-called ratcheting sequences. The band Tangerine Dream is famous for this kind of sequences. A normal sequencer generates only one gate signal per step. A ratcheting sequence may have also more than one gate pulses per step. This function can be obtained by using the A-160-5: one CV output of the sequencer is used to define the number of gate pulses per step. If the control of the step in question is fully CCW the generated CV is 0V and no gate signal is generated (mute of the step). When the control of the step in question is turned clockwise one, two or more gate pulses are generated depending upon the position of the mode switch and the voltage generated by the CV at this step.

Technical note: Due to the nature of clock multiplying it takes a few input clock pulses until the clock output is stable. One has to average a few input clock pulses to generate the multiplied clock output signal. Even when the input clock frequency changes it will take a few cycles until the output clock signal is correct as the module cannot foresee the future of the clock input signal. The generated clock output signal is derived from the last few cycles of the clock input signal. Consequently the module should be driven only by a clock signal with constant or slowly changing frequency.

Notes: Erica Synths Pico VCO 2 - powerful, full analogue VCO with great tracking over 8 octaves just in 3HP! Combine two of those, add some PWM and have a sound of real analogue beast!

Features:

Manual TUNE and PWM controls
+-1 octave switch
1V/oct input with good tracking across 8 octaves
PWM CV input
Pulse and triangle waveform outputs
Input protection against overvoltage
Protection against reverse PSU connection

Technical specification:

Output signal amplitude: -5V - +5
PWM CV input (full span): -5V - +5V
Power consumption: +21mA, -19mA
Module width: 3HP
Module depth: 35mm

Notes: The Octave Fuzz is SynthRotek's take on the classic 70's SuperFuzz circuit, made into a Eurorack module, which has improved on some aspects of the original as well, including an increased output.

Two distinct voices like the original: switchable between scooped midrange and massive midrange bump.

Aggressive: It will sound massive and in-your-face like no other circuit can. This is for sonic explorers and heavy music only. In short, it's not useful for EVERYTHING, but the things it DOES do it excels at. Sounds especially killer for keyboard and bass sounds.

Tuned to give a subtle distorted waveform one octave up via wavefolding (see the video to view this on an oscilloscope). (Completed modules come pre-tuned; there are calibration instructions at the end of the assembly instructions for the kits)

This circuit has been optimized for Eurorack. You can find a guitar pedal version here.

Current Draw:
32mA @ +12v
24mA @ -12v
0mA @ +5v

Notes: FONT is a massive sounding liquid filter- designed to bring you powerful basslines, tons of FM modulation and a clean resonance over your audio path.

It features two simultaneous outputs:
2-pole Low Pass
2-pole Band Pass

It can also work as a sine oscillator, tracking 1V/OCT when the resonance is at its maximum level.

FONT can be used to make basslines, acid patterns thanks to its organic and musically sounding resonance.

Ping it to produce percussion sounds such as, bongos, congas or toms.

Applying a pitch envelope, it really shines as a kick-drum machine!

22 mA +12V
25 mA -12V
0 mA 5V
15 mm deep
O 4.60 (10 Votes) Average Rating

Notes: Module A-160-2V is an enhanced version of the standard clock divider A-160. The module is a frequency divider for clock/trigger/gate signals, designed to be a source of lower frequencies, particularly for rhythm uses.

The Clock input will take any digital signal from, eg., an LFO, MIDI sync, or the gate from a MIDI-CV interface. At the outputs, you have access to three sets of seven different sub-divided clock signals, from half the clock frequency down to 1/128. The low/high levels of the output signals are 0V and about +10V.

The A-160-2V also has a reset input. Whenever a reset signal is sensed, all outputs are set to certain levels which depend upon the selected mode.

HP : 4

Notes: Arp is a gate-driven arpeggiator with a multitude of chord types and playback modes. Voltage control over both root note and chord type allow for sequencing any combination of chords in any key imaginable.

With the rate of the arpeggio and reset capability in your own hands, you're free to create dynamic rhythmic melodies from your favourite chords. Take your tonality for a ride with Arp.

Notes: This is a precision active buffer and multiple. This module has outstanding performance: it features very high input impedance, very low output impedance and an offset voltage of <1mV.

Not all active multi's are born equal, some designs do not fully solve impedance mismatch and tracking problems, or they apply offset voltages to the output and in rare cases can cause more problems than they solve!

AJH Synth have added a very useful (and unique) feature to cure tracking problems: four of the five outputs can be adjusted up or down by +/-5% from the front panel, so that VCO's and VCF's that don't track 1V/Oct exactly can be easily compensated to track correctly without having to re-calibrate the VCO or VCF themselves.

Notes: The ‘Pip Slope’ (rev II) is a compact envelope and function generator. It supports both Attack/Decay and Attack/Sustain/Decay type envelopes with both direct and voltage control of Attack and Decay times. Envelope shapes can be morphed between exponential, linear and logarithmic type slopes. Envelopes can be made to loop, repeating infinitely or decreasing with time or amplitude for echo and bouncing ball type effects. An ‘End of Cycle’ trigger output further extends the envelopes functionality for both clocking and burst or fill type effects.

The improved Pip Slope adds a number of new features and updates over the original Pip whilst keeping the same size. Improvements include increased output resolution, finer control of fast envelopes, a new morphing shape control, switchable 5v or 8v maximum envelope level, additional loop modes and an additional trigger output.

Features:
Compact envelope and function generator in 4HP.
Trigger and gate inputs.
Voltage and direct control of attack and release times.
Snappy or super long envelope times – ranging approx 1ms to 7 minutes per stage.
Optional self looping ability with 3 different loop modes: Decreasing amplitude, decreasing time, and regular loop.
Shape control that morphs the envelope shape from logarithmic to linear to exponential curves.
End of Slope trigger output that fires a trigger at the end the envelope or loop cycle.
Selectable 5v or 8v max envelope level output.
Reverse polarity protection.
Skiff friendly.
Designed and Made in the UK.

Technical Specifications
Supply: +12V 30mA / -12V 10mA
Size: 4HP
Depth: 38mm

Notes: Module A-199 is a spring reverb module. The reverb effect is electronically simulated by means of 3 spiral springs. Spring reverb systems have a very characteristic sound that is based on the (insufficient) mechanical properties of the springs like signal delays, audio resonances, limited frequency range, acoustic feedback behaviour, sensitivity to mechanical shocks and others.

The 3-spring system used in the A-199 ensures a "dense" reverb because of the different properties of the three springs.

The A-199 implies some special features that are not self-evident for spring reverb units:

The reverb signal can be fed back to the input using the Feedback control. Even self-oscillation of the springs similar to the self-oscillation of filters is available. The feedback loop can lead even via external modules like VCA, VCF, phaser, frequency shifter, vocoder, distortion/waveshaper, ring modulator and others. In this case the reverb output of the A-199 is connected to the input of the external module(s) and the output of the external module(s) is fed back to the Ext. Feedback In socket of the A-199. This socket contains a switch that interrupts the internal feedback loop as soon as a plug is inserted.

Another feature is the Emphasis control. This enables the adjustment of the accentuation of middle frequencies (around ~ 2kHz).

With the Mix control the relation between original and reverb signal appearing at the mix output is adjusted.

Using all these features very extreme and unusual effects can be generated with the A-199.

Notes: ADSR is a four stage linear envelope with two expressive ranges. Each stage can be modified independently allowing for the creation of complex, multi-segment envelopes. Great for modulating filters, VCAs, and oscillators.

Notes: Div is a 2 channel, voltage controlled clock divider and multiplier. Incoming clock signals can be multiplied or divided by a factor of 16 with a multitude of values in between.

CV inputs provide external control of the current clock rate, allowing for the creation of dynamic rhythms from a single clock signal.

Notes: DVCA

DVCA is a dual VCA based on the Mutable Instruments Veils. It features two separate voltage-controlled amplifiers, both with a gain and a response curve potentiometer, that is variable from linear to exponential. The outputs are normalized, so when no patch cable is present on output 1, output 2 will contain both signals, allowing the module to be used as a mixer. Several DVCAs can be daisy-chained for voltage-controlled mixer operation. It comes with jack lights that can be disabled via a jumper on the back.

These modules use tall bushing potentiometers to offer a more stable feel.

The module is fully assembled and tested. Eurorack power cable included.

Notes: SOLINA, an emulation of the 70ies string machines!

The SOLINA module is based on th excellen work of Jan Ostman, who has developed a very good digital based emuation of the sound of the string synths that were popular in the music of the 70ies and 80ies, like ARP Solina (who gave this module it's name), Logan String and others.

Their unique sound is based on several, minor detuned sawtooth oscillators and an ensemble effect.

This module produces chords, which can be shaped in different ways, like selecting the base scale (minor, major), adding the 7th or a bass note and different variations of the chord. The sound can be shaped with a variable oscilator spread/detune, adding a phaser/ensemble and a tone knob for choosing the overall character between bass focused to only higher parts of the sound.

Notes: Mix is a 4 channel mixer that is great for audio or control voltage signals. Up to four inputs can be combined to a single output each with its own level control.

Notes: The C-1U module is a one-channel module for recording and playing back movements of controller. Those can be recorded with channel's knob. The movements will be output as control voltage. The record time amounts to one minute maximal.

The track can be played once only (one shot) or in loop. The speed of the play back or the output offset is controllable with the pot. There are an additional CV input for CV recordings and a reset input.

The track data remains permanently stored when a 3V battery is used to buffer the RAM. When the module is switched on, the recorded data is available again. The module can be operated unipolar or bipolar (set by jumper on the back).

Note: The C-1U KnobRekorder uses a standard 3v lithium backup battery , type CR2032. The battery is needed to keep recordings and settings stored when the Eurorack case is turned off.

Dimensions: 12 HP
Power consumption: 20mA at +12 V and 9mA at -12 V

Module is a 1U tile.

Notes: This filter is based on the classic 2600 from the seventies and uses the LM3900 Norton opamp chip.

It has an audio inputs, two CV ins and an audio out.

You can control audio input level, CV levels, frequency cutoff and resonance.

It has a beautiful sound and it can go from relatively clean to dirty and screamy depending on audio signal level and resonance.

Tech specs:

- 8HP width
- 35mm depth behind front panel including the power connector
- standard 10 pin euro power +12V / -12V
- power consumption +12V 7mA , -12V 13mA

Notes: Module A-105-2 is a voltage controlled low pass filter with 24dB/octave slope.

It is the successor of the A-105 which had to be discontinued because the obsolete SSM2044 filter circuit. The A-105-2 is based on the SSI2144 which is in turn the successor circuit of the SSM2044. The features of both modules are nearly the same. The main difference is the clearly reduced front panel width of the A-105-2 (4HP instead of 8HP) and the associated changes of the controls and sockets positions. In addition the A-105-2 is equipped with 2 audio inputs.

The module has these controls and in/outputs available:

Control Frequ: manual frequency control
Control FCV2: attenuator for the frequency control voltage applied to socket FCV2
Control Q: manual resonance control
Control QCV: attenuator for the resonance control voltage applied to socket QCV
Control Input 1 Level: attenuator for the audio input signal applied to socket Input 1
Socket Input 1: audio input 1 (with attenuator)
Socket Input 2: audio input 2 (without attenuator)
Socket FCV1: frequency control voltage 1 (without attenuator, about 1V/oct scale)
Socket FCV2: frequency control voltage 2 (with attenuator)
Socket QCV: resonance control voltage (with attenuator)
Socket Out: audio output
Technical notes:

Frequency range: about 15Hz ... 15 kHz
Resonance up to self oscillation
Max. input voltage at Input 2 without clipping/distortion: about 15Vpp
Max. output voltage without clipping/distortion: about 15Vpp
The signals of both inputs are mixed before they are processed by the filter. This saves an external mixer for small setups.
Depth: 45 mm

HP : 4

Notes: Pont-Neuf is an adapeor module which converts between eurorack jacks (3,5mm / 1/8") jacks and banana plugs, providing a simple link between eurorack and Serge 4U systems. The module provides 8 bidirectional channels, is superslim and passive, i.e. does not require a power connection. It does provide a GND-banana-jack to establish a common ground between the systems.

Dimensions:
10 HP
24 mm deep

Notes: 3xVCA offers three high class amplifier circuits with linear characteristic. Thanks to AC / DC compatibility, a very low noise floor and basically no distortion, the module is not only a great partner for control voltages, but audio material as well. Besides a signal input and output, each VCA has its own CV input. The dual potentiometers regulate levels and bipolar CV attenuation values of all amplifiers. Using these rather unusual, yet very practical components, it was possible to equip the 3x VCA with a front panel that is only 6 HP wide. Switches allow the user to feed the results of one amplifier to the output of the next amplifier, so we can get 1+2, 2+3, and 1+2+3 outputs mix. Two-colored LEDs visualize CV and output signals.

60 mA +12V
60 mA -12V
35 mm Depth

Notes: Junction requires a +12V / -12v power supply with a 2x5 pin ribbon cable (included). The red line of the ribbon cable must be aligned with the -12V marking next to the module's power header and on your case's power distribution board. Junction draws 23mA from the +12 rail and 20mA from the -12 rail. Please ensure you have
enough power available before installing.

About Junction

Junction is a compact, 4 channel attenuverter, cascading mixer and multiple designed to fine tune the control voltages in your rack to the perfect range for their destinations. Junction can be used as a source of fixed voltage, offset another voltage, or mix multiple voltages together to create complex and dynamic modulation.

Features

Each channel on Junction has a knob (1) that acts as a manual control for the attenuverter. Center position (12 o clock) is 0V. The first channel input (2) is normalized to +5V when no cable is plugged into it.

A buffered copy of the input signal of the first channel is present on all of the other inputs from from the first (2) to the last (8). This duplication is "cascading" as shown by the arrow graphics on the panel - if a cable is patched into any input, it "breaks" the cascading multiple - all unpatched inputs carry the signal present at the uppermost patched input (or +5V if no inputs are patched). For example, if a signal is patched into the second channel's input (4) the third (6) and fourth (8) channel inputs would carry a copy of the second channel's input instead of the first channel input.

Junction's channels are mixed on the outputs. The output mixer is also "cascading" - when a cable is patched into an output, it carries a mix of it's own output and all unpatched channel outputs above it. For example, if only the last channel output (9) is patched, this output will carry a mix of all of the outputs. Patching the first channel output (3) would remove it from this mix.

Even though Junction's inputs cascade and outputs mix, Junction's output will clip at the Eurorack power rail voltages of +12 and -12V. It is not possible to output a voltage outside of this range, regardless of the signals patched into Junction.

23mA +12 / 20mA -12 4 HP / 25mm
Deep Reverse Power Protection

Notes: The 2hp VCA is a dual, linear VCA. It uses the renowned 2164 SSM architecture, giving it extremely low distortion and high quality audio outputs. With a CV input attenuator, and DC-coupled inputs this is your new go-to module for voltage controlled amplification of audio or CV.

Notes: A four channel mixer, suitable for audio or control signals. It features regular and inverted outputs as well as an LED level meter.

Specifications:
Current needs: +12V: 21mA, -12V: 10mA
Width: 5 HP
Depth: 20mm (including power connector)
Aluminiun, heat-treated front panel.
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: Pico EF is Erica Synths' take on envelope follower module in 3hp! Pico EF features a preamp with +40dB gain (enough to boost even guitar and dynamic microphone signals for use in a modular system), envelope output with adjustable attack time and a gate output with adjustable threshold. The Pico EF can be used as a preamp, overdrive unit or for controlling VCFs with audio signal, or to use with external instruments to control your modular system in other creative and experimental applications.

Technical specifications:

Preamp boost: up to +40dB
Audio output level: 10Vptp
Envelope output level: 0 - +10V
Gate level: +5V
Power consumption: 25mA, -15mA
Module width: 3HP
Module depth: 35mm

Notes: DRONX is a special mixer designed especially for the DRONE38 module; if has 6 input channels (so you can connect two DRONE38 modules) and offers some sound processing capabilities: A tone control with bass and treble control, a distortion, and finally a dual delay with different algorithms. Two insert points allow to add up to two more audio effects to the internal signal chain. Together with the DRONE38 module(s) you get a quite nice drone synth for dense, dark soundscapes.

Of course, it can be used with any other sound sources!

Notes: This small utility is the pedal's lover best friend, it allows 2 diferent chains of pedals to be independently connected to your synth.

The Send channels attenuate the synth level to instrument level.

The Return channels amplify the signal from instrument to synth level.

Specs:
- Width: 4 HP
- Depth: 3 cm
- Max current: 10mA

Notes: Inspired and officially licensed from Teia's Stochastic Function Generator which was introduced in 2013 but is no longer available. This earlier version served as an inspiration, but with a completely rebuilt and reprogrammed mcu to a fully featured 4 voice 2 stage envelope and slew generator.

ADDAC System ADDAC506B VC Stochastic Function Generator Expansion Module (black faceplateADDAC System ADDAC506B VC Stochastic Function Generator Expansion Module (black faceplate
This expansion allows extra I/O to the ADDAC506, namelly:

Four trigger inputs for the random engine.

Four CV random outputs from the random engine.