Back in stock: All genres

Notes: Great value from 4ms's twist on the Stereo Triggered Sampler module, this time capable of playing and manipulating stereo or mono WAV files from an SD card.

Supplier's Notes:
The Sampler is a variation of the Stereo Triggered Sampler.

Record, play and loop stereo .wav files with an SD Card. Includes the same 2022 Sampler Pack from the Stereo Triggered Sampler.

Features:

The Sampler plays stereo or mono .wav files from an SD Card. Samples are arranged into banks by placing .wav files into folders (each folder is a bank). A maximum of 10 samples can be loaded in a bank. There is a maximum of 60 banks (600 samples maximum total).
Sample files are limited to 4GB each, which is over 6 hours at 44k/16b/stereo.

Hundreds of samples included on microSD card
Extremely quiet, low noise and low jitter design
Stereo or Mono output

A knob and CV jack selects the Sample to play, and the Start Position knob and CV jack control where in the sample playback will begin. The Length knob and CV jack determine how much of the sample is played back: from tiny grains, to percussive hits, to longer loops... or just the entire file.

Pressing Play or firing a trigger into the Play Trig jack will play the sample. Holding the Play button down for a second will toggle looping.

There's also a Reverse button and jack for backwards playback, and an End Out jack for synchronizing loops, or cascading sample playback with other events.

To record samples, hold Play and Reverse for two seconds. Press Play again or fire a trigger into the Play/Rec Trig jack to start and stop recording. Each recording will create a new stereo 48kHz 24bit .wav file in the current bank's folder. Recordings can be as long as your card has the capacity for: a 256GB card is 18 days of continuous recording (432.9 hours). Audio data is split into maximum 4GB wav files on the microSD card.

Play button/trigger jack: Tapping the button or receiving a trigger starts/re-starts the sample
Sample CV/knob: select which sample within the channel's bank
Pitch CV and Pitch knob: playback pitch (-10 to +4 octave range)
Start Pos CV/knob: position in the sample to begin playback (loop start point)
Length CV/knob: playback time (loop end point)
Length knob at max: entire file is played
Length knob 50%-99%: 200ms - 5s of the sample is played (beginning at the Start Position)
Length knob <50%: Percussive decay envelope is applied to the playback (attack-only envelope if playing Reverse)
Length <1%: Tiny grains are played (can be used to sweep through sample file data manually)
Reverse button/jack: toggles forward/backwards
Bank button: selects channel's bank
Reverse + Start Pos button/knob combo allows for setting volume of playback
Maximum file size for playback: 4GB per file (6.7 hours per file at 44.1kHz/16b/stereo)
microSD Card is hot-swappable when Busy light is off: no power-down required to change cards.
Samples that are pre-loaded into memory can continue playing while card is swapped.

File Organization:

Using a computer, the intuitive automatic bank loading features make dragging and dropping your entire sample library a snap. No files need to be renamed. Just create folders and put up to 10 samples in each. If you want a folder to be associated with a particular colour of the Bank button, name the folder a colour name (such as "Blue - Loops").

Ships with a high-speed 16GB microSD card, loaded with hundreds of samples created for 4ms, from musicians such as Richard Devine, Wobbly, Moor Mother, Robert Aiki Aubrey Lowe, Joseph Pailo, Russell E.L. Butler, Hugo Paris & Marc Kate, Paul Barker, Baseck, Animal Collective, Cristian Vogel, Jay E, Marcus Fischer, Chris Carter, Daedelus, Nero Bellum, Anna Sitko, Thomas Fang, Bogdan Raczynski, and more (Sample List)

Intuitive bank/colour organization system; no need to rename your wav files
Record new samples directly to a bank with the Record Input jacks...
... or drag your folders of sound files onto the microSD card, and each folder will become a bank.
Folders starting with a colour name will be loaded into that colour bank
Example "Blue - Frooty Loops" will load into the Blue bank
Sub-folders are ignored, only folders in the root directory are scanned for wav files
Works best with UHS Speed Class 3 cards with |3| symbol printed on the card

Specs:

Electrical and Mechanical Specifications:
Module Size:
16 HP Eurorack format module
10-pin Eurorack power header
1.3" (33mm) maximum depth with power cable
Power consumption:
+12V: 135mA
-12V: 41mA
+5V rail: not used
Connect red stripe of power cable towards the bottom of the module, which is marked with a white stripe and the words -12V and POWER
Audio Inputs:
20Hz to 10kHz (+/-0.1dB); -6dB rolloff @ 20kHz
21V peak-to-peak maximum before clipping
Audio Outputs:
0Hz (DC) to 22kHz with maximum -1.8dB difference between file data and output
+10.5V to -10.5V maximum output
Trigger inputs:
Latency: 0.7us typi

Notes: EXP-FX, Il Sole e la Luna (eg. The Sun and the Moon) is an expansion module for Sibilla,
aiming to let you admire the same panorama under two different glows.

Depending on the Sibilla uploaded firmware, EXP-FX can either act as an actual Sibilla expander, giving you direct control on more Sibilla's parameters, or can turn your module into a stereo pitch shifting droning effect, allowing you to process your favourite oscillator the same way Sibilla processes its internal waveforms.

Every knob but the Line Gain is CV controllable and accepts i5V while the Freeze button can be activated with external triggers.

EXP, il Sole:
Everything regarding EXP is written with golden graphics on the module faceplate.
Expand your Sibilla by adding more control on the internal AR envelope and filter resonant
frequency. With the help of this firmware, Sibilla's controls stay untouched and the following

EXP commands are added:
ATTACK: sets the duration of the envelope attack stage. This is the time it takes for
the envelope level to go from zero to the maximum level when a gate signal is
received on Sibilla's trigger input. The duration is nearly zero with the knob fully
closed, and 5 seconds when the knob is fully clockwise.
RELEASE: sets the duration of the envelope release stage. This is the time it takes
for the envelope to go from its maximum level back to 0 after the gate is released
(max length is 5 seconds).
Q: sets the peak level of Sibilla's resonant LP filter (Resonance). When fully
counterclockwise, resonant peak will be rounded and become more apparent with
higher settings, depending on the harmonics created by Rise and Fall parameters of
Sibilla.

FX, la Luna
Everything regarding FX is written with white (black panel) or black (silver panel) graphics on the module faceplate.

With configurable eurorack/line stereo inputs, this firmware turns the whole duo (FX + Sibilla) into an intricate stereo pitch shifting delay droning effect. Splits your incoming sound in two separate pitch shifted tracks whose stereophony is affected by LFOs movements, white noise, delay lines and sampled bits of audio.

When installing this firmware, Sibilla's parameters perform the same functionalities as always, but applied to the incoming input audio signals:
RISE: pitch-shifts (from low to high pitch) the incoming sound on the left channel.
FALL: pitch-shifts (from high to low pitch) the incoming sound on the right channel.

As for Sibilla, the stereophony of these pitch-shifted tracks is affected by the movement of two free running LFOs with configurable waveforms and can be altered by a resonant LPF and the addition of a white noise source.

In addition, Sibilla's sampling delay network is now open and can be directly modified by the user:
BUFFER SIZE: controls the real time sampling window length. It's nearly 100ms
when the knob is fully closed and goes up to 1s with the knob fully clockwise.
FEEDBACK: controls the amount of sampled and pitch shifted audio sent back into
the sampler.
FREEZE: manually freezes the audio buffer to the last recorded bit of audio. While
frozen, the buffer size can still be modified.
GRAINS: sets the starting position of the audio bits to be recorded into the buffer
size (this feature still needs to be activated with a double tap on Sibilla's centre
button).

A small switch on the back of the module is used to shift between Eurorack and Line input signal. When Line inputs are configured, the Line Gain knob can be used to tame the incoming audio signal.

Width: 6HP Depth: 18mm

Material: 2mm anodised brushed aluminium front panel (black and silver)

Current draw: EXP-FX doesn't draw current directly from your system but relies on Sibilla's power; for this reason, depending on the uploaded firmware, Sibilla's power consumption will change as follows:
Sibilla + EXP: +12V: 140mA; -12V: 33mA; +5V: 0mA;
Sibilla + FX: +12V: 142mA; -12V: 35mA; +5V: 0mA;

Notes: Welcome to the Envy Machine ! A compact quad-channel modulation machine, with an envious array of Envelopes, LFOs, random voltages even Knob Recording. With four channels of modulation, ENVY MACHINE makes an ideal companion to the RYK ALGO module

Each of the four channels on the ENVY MACHINE can be set to one of five super-flexible modulation modes:

- ADSR Envelope

- AD Envelope

- AD LFO

- Random Voltage

- Recordable Knob Voltage Control

Ghost hand - Parameters can be animated using KNOB RECORDING to create timed variations in your patch. Oh, and with the dedicated MOD input per channel, you can use an external CV to control anything - TIME, LEVEL, WAVESHAPE and more.

Polarity paradox - Modulation inputs AND channel Outputs come with bipolar attenuverters, now you can choose either bipolar or unipolar, with continuously variable level control.

Slippery slopes - WAVESHAPES are continuously variable between LOG, EXPO, SIN, TRAPEZOID, and SQUARE!

Notes: Turing Machine MkII is a binary sequencer, based around a 16-bit memory circuit called a shift register. It's designed as a sequencer that you can steer in one direction or another, not one that you can program precisely.

You cannot program this sequencer to play specific tunes. You cannot save sequences. You can never go back to a sequence that has changed.

To put it another way: This random looping sequencer is a module that produces clocked randomly changing control voltages. Unlike many random voltage generators, these sequences can be locked into loops that repeat according to the length control.

Specifications:

Width: 10HP
Depth: 38mm
Current draw:
+12V: 40mA
-12V: 0mA

Notes: This is a fully built module, with the latest firmware pre-installed. Comes with Rogan knobs. You can swap our panel for another manufacturer's panel!

Mutable Instruments Plaits is a multi-algorithm macro-oscillator that provides everything from FM to speech synthesis, analogue percussion emulation, wavetables, modal synthesis, granular synthesis...whoa, this module does basically everything. Expanding on Braids's strong points and eliminating its pitfalls, Emilie Gillet's Plaits is a perfect bonding of tremendous flexibility and an intuitive user interface.

Built from the ground up and sharing no code or hardware with Braids, Plaits borrows concepts from its predecessor while operating at considerably higher audio resolution and with a refined means of user interaction. For one, it dispenses with that pesky screen to offer even more tactility and immediacy. Additionally, Plaits features a dedicated CV input for the model parameter, easy access to the module's internal envelopes for modulation of vital parameters, and an integrated lowpass gate with definable filtering intensity and virtual vactrol response time.

Offering a broad survey of synthesis techniques, Plaits promises a vast sonic palette that could find a home in any modular synthesizer setup. Ideal for beginners and modular synth gurus alike, Plaits is an obvious choice for anyone who wants a lot of functionality in a small space and with a modest price tag.

Specifications

Width: 12HP
Depth: 25mm
Current draw
+12V: 50mA
-12V: 5mA