Tascam

Notes: The DR-70D is a compact audio recorder that allows the aspiring DSLR user to create audio recordings in very high quality in parallel to their film or video shots. The recorder can be mounted directly between a tripod and the camera or on top of the camera, resulting in a compact package.

With its two built-in microphones, the DR-70D is instantly ready for use in standard situations. In addition, it provides four XLR/TRS combo jacks which can be used to record four channels of audio with excellent sound quality using professional microphones. Thanks to a camera output the recorder's stereo signal can be recorded also on the camera to ease subsequent editing of the material in combination with the slate tone function of the recorder. On the other hand you can use the camera input to monitor the audio of the camera using the recorder.

Features of the DR-70D include overload-resistant, great-sounding preamps with switchable low-cut filter and limiter, handling of microphone signals in mid/side format, 24- or 48-volts phantom power for condenser mics, as well as many common and not so common functions that facilitate capturing, monitoring and subsequent processing of the audio tracks.

The two omnidirectional microphones allow you to easily record natural stereo sound with just this unit. Used together with small shotgun mics, you can even record audio from people speaking in an interview and the ambient sound at the same time (on different tracks), for example, with a compact set up.

The four-channel design enables use of two shotgun mics and the stereo mic to record ambiance and each speaker individually. Since channels 1 and 2 can be set to the stereo input and channels 3 and 4 can be set to the built-in mic, a large variety of microphone setups is possible.

MONO/DUAL MONO mode: This is best for recording the audio of a single performer.
STEREO/DUAL STEREO mode: This is best for recording with the built-in microphone or a stereo mic.
2MIX/DUAL 2MIX mode: This creates stereo files of the signals of multiple inputs that have been mixed.

The mixer can take a total of 4 channels from among the four XLR inputs that support phantom power, the stereo mini-jack input and the built-in stereo mic. In addition to adjust pan and input level, this unit also offers a limiter, a five-setting low-cut filter and a delay that can compensate for distances between mics. Moreover, a mid-side decoding function allows the use of two microphones in mid-side configuration.

Mic preamps, which receive and amplify microphone input signals, have a large impact on the quality of the recorded audio material. The DR-70D uses Tascam original HDDA (High Definition Discrete Architecture) microphone preamps that we created through careful selection of parts. For example, we chose the NE5532 for the operational amplifier, which has a strong effect on audio quality. With a mic amp circuit that uses discrete architecture comprised of meticulously-chosen parts, we have achieved an equivalent input noise of -120 dBu.

The A/D converter that converts analogue signals to digital is made by Cirrus Logic and is equivalent to those used in our successful DR series of linear PCM recorders. Recording at resolutions up to 96 kHz/24 bit is supported.

The designer of the DR-70D focused on making the unit small so that it does not interfere with camera-work when it is attached to a camera support system or stabilizer. The unit has tripod screw threads on the bottom side and a removable camera attachment screw on its top. A hot shoe mount is also included so you can attach the recorder in the way most convenient for you by placing it between a tripod and the camera or on top of the camera with a hot shoe.

Stand adapter (14 inch) on bottom side to attach the unit to a tripod
DSLR bracket for easy camera attachment and removal
Hot shoe mount (accessible when not using the DSLR bracket)
Handles on the front left and right sides protect the screen and can be used to attach a shoulder belt

The DR-70D has a camera input jack that can be used to monitor the audio from the DSLR camera. By using this with the DR-70D monitor selection function, you can efficiently monitor the audio from not only the DR-70D but also from the DSLR camera.

The camera output jack is designed to output the mixed audio to the camera so that the same audio can be recorded by the DR-70D and the camera. Since the input level varies by camera maker and there are usually few adjustments related to volume on DSLR cameras, this unit has an output volume dial that can be used to make adjustments.

The built-in generator can produce slate tones that can be used as references when aligning audio and video. In addition to being able to produce slate tones when recording starts or when it starts and stops, the SLATE button can be used to add slate tones at any desired point.

Automatic insertion: Choose from inserting a slate tone at the beginning of recording or at both the beginning and end of recording
Manual insertion: Press the SLATE button to produce a tone.

Features at a glance
Compact, professional-grade audio recorder designed to be used in combination with a DSLR camera
Uses an SD/SDHC/SDXC card as recording medium (up to 128 GB)
High-quality recording inputs through Tascam original High Definition Discrete Architecture (HDDA) microphone preamps
NE5532 operational amplifiers for even higher audio performance (also used on DA-3000)
In addition to ordinary stereo recording, simultaneous recording of up to four channels is possible
Four channels can be mixed down to a stereo signal
Recording levels can be adjusted independently for inputs 1-4
Dual recording function allows two files to be recorded simultaneously at different levels
Recording at 44.1/48/96 kHz, 16/24-bit, linear PCM (WAV format)
Broadcast Wave Format (BWF) supported as WAV recording format
Two built-in omnidirectional microphones
Four XLR/TRS combo inputs can provide phantom power (+24V/+48V)
+24 dBu maximum input level (20 dB headroom)
Additional unbalanced input for channels 1 and 2 (stereo mini jack) supports mics that require plug-in power, allowing the input of video mics and other high-output mics
Switchable low-cut filter conveniently reduces low-frequency noise (40/80/120/180/220 Hz)
Switchable limiter to prevent clipping
Audio can be output to a DSLR camera for recording
Camera input enables convenient monitoring of audio from a DSLR camera
Selectable mid-side decoding for use with MS microphone setups
Slate tone functions (automatic/manual) to simplify synchronization of video files when editing
A new file can be created during recording
Selectable delay to eliminate time lags caused by differences in the distances of two input sources
QUICK button allows easy access to various functions
Slate tones can also be used for moving to specific locations
Equalizers for playback, and level alignment function to enhance the perceived overall sound pressure
File name format can be set to use a user-defined word or the date
Resume function to memorize the playback position before the unit is turned off
Line output and headphones output with individual level controls (3.5-mm jack)
Dedicated remote control jack for use with RC-10 and RC-3F (sold separately)
Hold switch to prevent accidental operation
Low-noise buttons
128 x 64 pixel LC display with backlight
USB 2.0 port
Stand adapter (14 inch) on bottom side to attach the unit to a tripod
DSLR bracket for easy camera attachment and removal
Hot shoe mount (accessible when not using the DSLR bracket)
Handles on the front left and right sides protect the screen and can be used to attach a shoulder belt
Operates on four AA batteries, an optional AC adapter (Tascam PS-P520U), optional external battery pack (Tascam BP-6AA) or USB bus power

Notes: Classic Multitrack Recording

Digital Recording and Mixing with Analogue Gear Made Easy

The Studio Bridge multitrack recorder is quite literally the bridge between analogue mixing and digital recording - regardless of whether you use a DAW or not. Preserve the lush analogue tone from your mixing console while recording tracks with the DAW of your choice or with Studio Bridge itself. Either way, tracks can be returned to your analogue console for mix summing, turning digital recordings into warm analogue productions.

Whether you're recording in a personal studio or in a live environment, the Tascam Studio Bridge serves as a link between your existing equipment, complementing it with the latest recording technology and ease of use in a rack-mountable format.

24-Track Recording Without a Computer:

Connect your analogue mixer to the modular Studio Bridge recorder and easily record up to 24 audio tracks - no computer required. You can even record your stereo mix to the recorder and export stereo WAV files for release-ready productions.

24-In/24-Out Audio/MIDI Interface for DAWs:

Tascam knows you want true analogue flavour on your DAW recordings, and we're here to help. Your analogue mixer can easily connect to your DAW using the Studio Bridge as an audio interface with 24 inputs and outputs. You can record directly to any DAW and even create a summed mix using your console and outboard gear with audio returns.

DAW Transport Controller and Dedicated Meter Bridge Software:

Studio Bridge also works as a DAW transport controller. Rec/Play/Stop and Rec Ready buttons link directly to your DAW for ease of use.
The settings panel, available for Windows and macOS, includes a digital meter bridge so you can keep an eye on the audio levels of each track and the stereo master.

MIDI Synchronisation for Your Sequencers:

With MIDI in/out ports, your favourite drum machines, sequencers, synths and controllers can easily be integrated into any production. Unlock your creativity with your go-to analogue hardware and the Studio Bridge.

Live Recording Applications:

In live environments the Studio Bridge becomes your mobile recording studio when connected to your mixing console.

Just one piece of gear - no complex system, no computer required.