Search dance music

Notes: The NVO-1 is an analogue noise synthesizer that's capable of producing a wide variety of sounds. Adjust the Main Frequency and Sub Frequency knob to create deep textures and flip the noise switch to bring out even more tones.

Notes: JMT have designed a very complex interplay between the two oscillators, using two different oscillator circuits with different circuit configurations, and two different waveform conversion circuits attached to each. The output is then routed through a circuit that was developed from the SNB-2b, which emphasizes and distorts the bass, mids, and treble, and which have been tuned to work well with this oscillator.

Fine-tuning of circuit part values was performed to obtain a sound with depth as well as intense distortion by fine-tuning the knobs.

This runs on DC 9V negative center or a 9v battery.

Noisy analogue synthesizer oscillator with distortion function that can emphasize HI, MID, and LO.

The oscillator can be input to a VCO with a wide range and a SUB VCO adjustable by LEVEL.

The VCO and SUB VCO are designed to affect each other in complex ways, so a wide range of sounds can be created by subtle combinations of knob positions.

The MODE switch makes the connection between the SUB VCO and VCO more complex, and the LEVEL knob can be used to adjust the level of the SUB input to create different waveform changes.

By fine-tuning the LEVEL, SUB, VCO knob, you can create a variety of sounds by emphasizing high, mid, and low frequencies.

The CV IN jack is a 3.5mm jack. OUT PUT 6.5mm

Notes: The JMT RVO-3 is an analog noise synthesiser featuring 2 oscillators. 1 main oscillators with 1 sub oscillators paired to it. Each of the oscillators features their own frequency controls, and sync switches for each of the oscillators pairings allowing a wide range of textures. It has a main VCO with a frequency control knob and a push button allowing a short envelope to control the frequency. Additionally, controls for the waveshapes and stability of the VCO and sub frequency VCO allow for further manipulation of timbre.

Notes: The JMT Synth NOISY MIC-2 is a unique vocal instrument and processor designed for extreme textures stemming from the human voice. The multiplexer circuit combines the microphone output with a switchable internal VCO, this mixed signal is then passed through a high-gain distortion equipped with an equalizer for final tone-shaping. The VCO can be modulated by an LFO or an external CV source for complex FM-like timbres. This combination of simple circuits forms a unique vocal processor with a wide range of timbres and effects. The microphone is outfitted with a mute switch, making it suitable for live performance.

*Do not connect any other equipment except the included microphone. It is different from normal Midi terminals in that it has special wiring, so connecting other objects to it will damage the circuitry.*

Notes: The NOSC-12, from JMT Synth, is a 12 oscillator drone synthesiser, six main oscillators with six sub oscillators. There are frequency controls for each of the oscillators, including the sub oscillators, which also include sync switches for each of the oscillator pairs. Each of the oscillators are mixed together to a 1/4" output jack.

NOSC-12 Features

12 Oscillator Drone Synth
12 Suboscillators, one per Osc
Volume Controls for each OSC
Sync switches for each OSC.

Notes: The TVCO-2 is an analogue synth that is powered by a single DC9V~DC12V or 9V battery.

By touching the five sensors directly connected to the circuit of the analogue synth oscillator with your fingertips, the tone of the oscillator peculiar to thick analog synths changes in various ways.

Since it responds delicately, the tone changes depending on whether you touch it strongly or touch the sensor with or without touching it, and whether you touch two, three, or a combination.

The top two sensors are connected to the MAIN VCO and the SUB VCO for input to the VCF, so you can use this sensor to change the VCF (filter) with touch sense to create more complex tones.

The bottom three sensors are connected to the circuit of the MAIN VCO. This sensor can make a noisy change directly to the main sound output oscillator, and the way it changes changes with a combination of touches, such as touching it at the same time in combination with the touch of the SUB VCO.

With a simple structure of 2 VCOs and 1 VCF (band-pass and low-pass switchable), you can intuitively operate this equipment to create your own sounds.

The MAIN VCO and VCF have CV IN. By attaching a 3.5mm conversion jack, you can connect from sequencers, analog synths, and modular synths CV OUT for a wider variety of expressions.

Compared to cable patches and switches, subtle changes can be made instantly at the fingertips, so it is a model that can be controlled more sensitively.

This analogue synth runs on DC9V negative center or a 9V battery.

The main VCO can be controlled with FREQ. knob and 3 touch sennsors.

Sub VCO has two touch sensors and effects to main VCO and VCF as CV.

CV INs can recieve CV OUT of other instruments,sequencer, LFO, etc..

Notes: Really nice boutique analogue synth from JMT, based around a main oscillator with three sub signals, a frequency-synced resonant filter, noise source and three-speed random trigger.

Supplier's Notes:
DNVO-1 is a handmade, compact analog synthesizer from JMT Synth Its primary oscillator can be synced with three sub oscillators, each with a different range, as well as a noise source and wave generator. The latter source can be manipulated with the 3-speed random trigger for effective fluctuations within a single performance. The primary VCO is routed through a self-oscillating filter, which can sync with the VCO's frequency.

Notes: Two VCOs (oscillators) are input to the VCF (filter) and output through DELAY (can be turned off).

The VCO can be a 4LFO module, which is a mix of 4 LFOs, a noisegenerator, an LFO, and a SUB OSCILLATOR, and the VCF can be an LFO.

With a variety of tones, you can create various sounds even with a subtle knob position.

It can be used with a single 9V battery or a 9V DC center negative adapter.

CV IN can be used with CV input to the filter. (VCO1.2,VCF)

INPUT is capable of audio input. The input sound goes to the filter- delay (can be turned on and off) in parallel with the built-in VCO.

CV IN can be input from +8 volts to -8 volts.

This analogue synth runs on DC9V negativecenter or a 9V battery. 2 VCOs go to VCF and Delay. VCO receives 4 modulations inside. NOISE GENERATOR,4 mixed LFO and SUB OSC. VCF receives CV of LFO.It becomes the wave filter with it. ? Delay section has the on/bypass switch. INPUT goes to VCF and DELAY with internal VCOs.

Notes: The JMT VDR-1 is a synthesis-based percussion box made for pulsing noise that morphs from jarring bursts to highly tuned drum sounds. The VDR-1 gives the user a flexible drum voice in a small package with CV control of both the filter and the oscillator. Coupled with a capable LFO the VDR-1 is a great drum voice solution, with a no-frills aesthetic perfect for any synthesist from Monolake to Merzbow.

VDR-1 Features

VCO can morph between triangle and swatooth waveform
LFO for modulation of the VCO and VCF
Internal MIC for triggering of VCF and VCO
CV in for modulation of both VCO and VCF

This is a synth drum with a built-in self-oscillating VCF.

It is equipped with a wideband oscillator and has a strong SWEEP effect.

You can create various tones by tapping on the body or with an external trigger (sequencer or piezo).

The oscillator has a thicker sound from highs to lows, and the waveform can be selected as TRIANGLE or SAWTOOTH.

SWEEP is set to be applied very strongly, so adjust it in conjunction with CUT OFF COARSE.

SUSUTAIN Setting of the decay time from the onset of sound

SENSITIVITY TRIGGER (When the plug is inserted into the trigger, the internal trigger of the unit is turned off) is to adjust the input sensitivity of the SENSITIVITY TRIGGER.

LFO.F controls the amount of LFO applied to the filter and LFO.

LFO.O controls the amount of LFO applied to the oscillator.

FINE is a finer pitch control for the oscillator than COARSE.

The RESONANCE oscillates at maximum and the pitch can be changed with the CUT OFF knob.

It can be powered by either a center minus 9V DC or 9V battery.

SYNTH DRUM

self-oscillate VCF with CUT OFF and RESONANCE

VCO triangle - sawtooth waveform

LFO.F LFO level for VCF

LFO.O LFO level for VCO

CV IN.F cvin for VCF

CV IN.O cvin for VCO

SENS. sensitivity for trigger to synth-drum

SWEEP

SUSTAIN

FORM waveform of LFO

RATE rate of LFO

NOISE level to VCO

Runs on DC9V negative center or a 9V battery.

Notes: The JMT Synth NOISY MIC-1 is a unique vocal instrument that specialises in intense, noisy textures. The simple design consists of an original circuit designed by JMT Synth, that mangles incoming audio into unique timbres unlike that from any other vocal processor. A single volume control and button based on/off switch ensures the NOISY-MIC 1 is ideal for live performance.

Notes: The NDE-1 is JMT Synth's flagship synthesiser, capable of a wide range of sounds. Consisting of two VCOs, a sample & hold function, a noise generator, a low-pass filter, a LFO, VCA, and an envelope generator. This combination can create a powerful and variable sound. The 4-pole filter works very smoothly, and an external audio input. It can be paired with a sequencer for live performance and a wider range of sounds.

Notes: Nice experimental stuff from JMT. Dual oscillators and noise circuits interact to create unique drones, soundscapes and synth tones. Knobby front panel gives plenty of hands-on control.

Supplier's Notes:
Two VCOs with different circuit configurations are used, each with two types of waveform conversion circuits, one of which is a noise synthesis circuit created by the VCO input, to design complex interactions.

The output is input to a sustain circuit, a delay, via a distortion circuit that emphasizes bass, mid, and treble.

4 mixed CV/GATE sends the gate to the sustain circuit at the timing when it is mixed with the four rate knobs, and pronounces it at the timing of the gate like a drum synth. . The sustain length can be set with a knob. At the same time, the CV is also sent to the two VCOs (adjusted with the LV knob). The delay can be turned on and off with a switch.

Fine-tuning the numerical values of the circuit components and fine-tuning the knobs can obtain not only intense distortion but also delicately varied sounds.

CV IN is input to the VCO.

It is driven by a center minus DC 9V adaptor. A 12 V DC adapter can also be used for the power supply.

Increasing the voltage changes the range and setting range. Up to 12V

Two VCOs with different circuit configurations, each with two different waveform conversion circuits, one with a noise synthesis circuit created by the VCO input, a very complex interaction is designed.

The output is routed to the sustain circuit and delay via a distortion circuit that emphasizes lows, mids, and highs. 4 MIXED CV/GATE sends GATE to the SUSUTAIN circuit at the timing mixed by the 4 RATE knobs to produce a GATE timing like a drum synthesizer. Sustain can be set with the knob. At the same time, CV is sent to the two VCOs (adjustable with the LV knob) by this circuit.

Delay can be turned on and off with a switch.

Fine tuning of the values of the circuit components and fine adjustment of the knobs allows you to obtain not only intense distortion but also subtle variations. cv in is input to the VCO.

It is powered by a center-minus DC 9V - DC12V adapter.

A 12 VDC adapter can also be used for power supply.

Increasing the voltage (up to 12 V ) changes the sound range and setting range.

Features:

2 VCOs
Noise Generator
Gate Generator
Distortion for highs, mids, and lows
VCA with sustain envelope
Delay
9V power supply (center negative) is included

Notes: The UNVO-1b powered by a centre negative DC 9V adapter or a single 9V battery.

It also contains two VCOs (oscillators) with a wide range.

The frequency and waveform of the SUB oscillator are changed, and they are input to the main, respectively. Each of them has a range switch, so it works like an LFO under the switch. The colour of the range switch (white, black) corresponds to the colour of the SUB.1 and SUB.2 on-off switches next to the FREQ knob of the main oscillator.

When the WAVE switch is turned on, the WAVE knob is activated, and the SUB OSCILLATOR.1 and 2 are shaken.

The main VCO×2 is mixed and fed into the strain + filter circuit. This special filter has a FREQ knob and a TUNE knob. The TUNE knob powerfully amplifies the input signal while also tracking specific pronunciations.

The filter is a circuit that has been fine-tuned so that it can very effectively enhance the bass and treble of this input signal.

Unlike other switches, the noise-on switch moves sideways, left (VCO.1), middle (OFF), and right (VCO.2). They are populated in VCO.1 and 2, respectively.

The UNVO-1b is a noise machine that can output a very strong signal that generates a variety of noise sounds.

The black painted aluminium die-cast case is painted with a black matte paint with a laser and scraped to make letters.

This analogue synth runs on DC9V negative centre or a 9V battery.

The main 2 VCOs can receive 2 oscillators and noise generator inside and go to 2 different filters.

2 oscillators can be tuned with each two FREQ. knobs and controlled with the wave knob.

RED switch is for wave knob working.
Black and White for tone of oscillators

Notes: No-nonsense analogue business here from JMT. Square wave VCO and sub-oscillators can be morphed and wave folded to create unique timbres.

Supplier's Notes:
The JMT Synth EWG is a desktop analog synthesiser with a wide-ranging VCO and two reconfigurable sub-oscillators that emit square waves, ideal for thick bass tones. Two adjacent knobs can control the pulse of the square waves, allowing for a wide range of tones and timbres. Two reduce knobs govern the leve of each sub-oscillator, allowing the user to blend the tones to their taste. The EWG-1 is powered by a DC9V center negative adapter or a single 9V battery.

Notes: Part of JMT's no-frills synth range, the SNB-2b offers a single voltage-controlled oscillator with three sub-oscillators, allowing you to blend and distort harmonics to create thick, juicy tones.

Supplier's Notes:
The SNB-2b is powered by a centre negative DC 9V adapter or a single 9V battery.

The SNB-2b is a noisy analogue synth oscillator with a distortion function that can emphasize HI, MID, and LO.

The oscillator can be input to the MAIN VCO with a wide range, and the three complex input SUB oscillators can be adjusted at LEVEL and input to the MAIN VCO.

Each of the three SUB oscillators is designed to affect each other, so a wide range of settings are possible with subtle knob position combinations.

The three oscillators are directly input to the waveform of the MAIN VCO, and different waveform changes can be added by adjusting the input level with the LEVEL knob.

It is a model that expands the variety of sounds by fine-tuning the knob and emphasizing the high, mid, and low frequencies of various tones such as noisy dense sounds and intermittent sounds.

From CV IN, you can input CV OUT (sequencer, analogue synth, modular synth) of other equipment and change the MAIN VCO. Since it is a 6.5mm jack, please use a conversion plug when using a 3.5mm cable.

Runs on DC9V negative centre or a 9V battery.

3 sub oscillator effect each other go to main VCO with LEVEL knob.

The main VCO goes to DISTORTION circuit with HI,MID,LO knobs.

The SNB-2b makes a variety of sounds.

CV IN is for VCO pitch. It accepts+-9V voltages.

Notes: Quirky synth fun from JMT, the NDE-1 is based around two oscillators, sample and hold, noise generator and a four-pole low-pass filter. Generate random tones, control via a sequencer or process external audio.

Supplier's Notes:
This model consists of two VCOs (oscillators), SAMPLE & HOLD, noise generator, low-pass filter, LFO, VCA, and envelope generator to create a powerful sound.

By itself, a wide range of sounds can be created, including random and regular intermittent sounds, mute timing, and fine-tuning of levels.

If you input sounds from other equipment through the A IN, you can apply a variety of filters, LFOs that oscillate the filters, and mutes to the input sounds in parallel with the built-in oscillator.

The variable range is wide enough to produce a variety of sounds. The filter is a 4-pole filter that works very smoothly, and external audio can be input via A IN.

You can also use it with a sequencer to create even more sounds.

CV INPUTs can accept - + 9V. Do not exceed this voltage.

The adapter is not included.

Please use centre negative 9V POWER SUPPLY or A 9V battery.

Notes: Excellent basic analogue synth with its own distinctive character. The UNVO-1 is a two-oscillator design with a 'strain' and filter circuit to sculpt your sound. Control via the knobby front panel for experimental tones and powerful bass sounds.

Supplier's Notes:
It is powered by a center negative DC 9V adapter or a single 9V battery.

It contains two VCOs (oscillators) with a wide range.

The SUB oscillator has a different frequency and waveform, and is input to the main, respectively. Each of them has a range switch, so it works like an LFO under the switch. The color of the range switch (white, black) corresponds to the color of the SUB.1 and SUB.2 on-off switches next to the FREQ knob of the main oscillator.

When the WAVE switch is turned on, the WAVE knob is activated, and the SUB OSCILLATOR.1 and 2 are shaken.

The main VCO×2 is mixed and fed into the strain + filter circuit. This special filter has a FREQ knob and a TUNE knob. The TUNE knob powerfully amplifies the input signal while also tracking specific pronunciations.

The filter is a circuit that has been fine-tuned so that it can very effectively enhance the bass and treble of this input signal.

Unlike other switches, the noise-on switch moves sideways, left (VCO.1), middle (OFF), and right (VCO.2). They are populated in VCO.1 and 2, respectively.

It is a noise machine that can output a very strong signal that generates a variety of noise sounds.

This analogue synth runs on DC9V negative center or a 9V battery.

The main 2 VCOs can receive 2 oscillators and noise generator inside and go to 2 different filters.

2 oscillators can be tuned with each two FREQ. knobs and controlled with the wave knob.

RED switch is for wave knob working.

Black and White for tone of oscillators

Notes: EGL-1 is a desktop analogue synthesiser that is ideal for a variety of duties. The unit's sub-oscillator can be configured to determine the emitted waveform and decays when the Push switch is pressed. There are four LFOs routed to the primary VCO for bountiful modulation capabilities. The VCO itself is routed through a boost circuit for a some extra flair that's sure to punish listeners in all the right ways.

EGL-1 Features

VCO routed through boost circuit
4 LFOs provide ample modulation possibilities
Integrated sub-oscillator
Push switch causes the sub-oscillator to decay
Two types of modulation can be applied to the MAIN VCO (oscillator).

The bottom stage mixes four LFOs and allows you to adjust the input level to the MAIN VCO with the level.

The middle stage allows you to input a WAVE to the SUB OSC (another oscillator) with adjustable rise and fall of the oscillator, which can then be fed into the MAIN VCO.

The push-button in the top right-hand corner rapidly decays the power of the SUB OSC as long as it is pressed. While it decays, it has an effect on the sound of the MAIN VCO.

The MAIN VCO output also has an output circuit to make the sound more powerful.

The EGL-1 operates from a 9V centre-minus or battery. Neither is included.