Flame

Notes: Automix is a compact three-channel mixer for audio signals and control voltages. The highlight of this module is the recording function, which makes it possible to automate level changes.

The "AUTOMIX" module is a compact three-channel mixer for audio or CV sources in the voltage range of +-5v (audio modular level).
The mix level of each track can be adjusted and recorded using the track's control. The recording time per track is over a minute. The playback speed is also adjustable.
The recorded track is played once with a short press of the play button (one shot) or with a slightly longer press in the loop.
In addition, the 3 inputs can be switched separately to +6db audio via a slide switch on the back (for external line level sources).
All three tracks have a common reset input. The track data is stored permanently (battery-backed memory).

Overview:

Signal/audio mixer with 3 channels on a sum output

- 3 tracks with 1 mix control each
- Record time (per track) max. 102 sec
- 3 signal/audio inputs (audio or CV) (-5v.. +5v)
- Inputs switchable to audio with line level (separately for each input)
- Resolution 12bit
- Sampling rate approx. 250Hz
- Modes:
- Play back one shot
- play back loop
- Switch between play back and potentiomix manually
- Adjustable playback speed
- Track data permanently stored (battery buffered)
- Common reset input for all 3 tracks

Dimensions
6 HP
38 mm deep

Current Draw
40 mA +12V
30 mA -12V

Notes: The FLAME "C-3 MK2" is a three-channel module for recording and playing back movements of controllers. These can be recorded with each channel's individual knob. The movements will be output as control voltages. The recording time per track is over one minute. The playback speed is adjustable. All three tracks have a common reset input. The track data remains permanently stored (battery-backed memory). The module can be globally switched to bipolar or unipolar voltage range (switch on the PCB).

Notes: Small compact joystick module with recording function.

The module can record the joystick movement to a length of about one minute. The sequence remains stored in the battery-backed RAM after switching off. When playing back the sequence, the playback speed can be manipulated.

There is a FREEZE function to hold the current joystick position. Also there are an external reset input. In addition, when moving outside the center position, a GATE is set and an additional positive CV voltage (summation of X and Y) is output in dependence. A GATE / START input is used for resetting or recording in sync.

The ranges of the X / Y output voltages are bipolar adjustable from approx. +/- 5v or unipolar from approx. 0 to + 10v. Both channels X and Y have a passive attenuator potentiometer, so that the voltage range can also be set lower.

Connections:

CV-Out-X: CV output X-axis bipolar or unipolar
CV-Out-Y: CV output Y-axis bipolar or unipolar
CV-OUT MOVE: CV output joystick movement 0..+5v
Trigger-In: Trigger input Reset/Start
Trigger-out: Trigger output Reset/Start signal ca. 10ms lenght
Gate-ACTIVITY: Gate output joystick movement

Power consumption: 30mA at +12 V and 5mA at -12 V

Depth: 40mm

8 HP

Notes: The module inverts an applied positive voltage so that the maximum value becomes zero and zero becomes the maximum value.

The input voltage is not inverted into the negative voltage range (mirror axis 0v) but mirrors a positive voltage around an adjustable axis within a fixed positive voltage range starting at 0v.

There are 10 ranges, adjustable in 1V steps.
The mirror axis is always at half of the set range.

If no cable is plugged into the input socket, the output voltages can be regulated manually with the "Manualy" potentiometer.

The module has two similar function groups.

Applications are for example the inversion within positive voltage ranges, GATE inversions (0/+5v to +5v/0v), or opposite melody lines.

Dimensions
6 HP