Studio Equipment charts

Notes: Dual 1x5 Passive Multiple

Two rows of 1 x 5 Passive Multing

Notes: The shorter and wider brother to the popular Triatt module!

The four handy knobs can act as active attenuators (unipolar) or attenuverters (bipolar) depending on the setting of the two-position switches above each one.

Each input is normalled to a precision +5V DC voltage source. With nothing plugged into the jacks, each knob controls a voltage range of 0 to +5 v or -5 to +5 v depending on the position of the mode switch.

- 2 modes for each channel
- 5v normalled to each input
- With external signals it acts as active/buffered attenuator/attenuverter/mixer
- Each output normalled to mix into the adjacent channel on the right making it possible to do sub mixes in groups of 2, 3 or all four channels.

Notes: MX12 as successor of the UC44 is a universal controller for all kinds of MIDI controllable hardware and software.

You can combine NEW MODULE devices to a large system. The connections are on the right side to allow a back to back placing of two or more devices. Connect two NEW MODULES by a special extension port.

Furthermore, there are 4 MIDI-ports and one USB-port with various routing possibilities.

It is packed in a metal case with the same dimensions like the famous ELEKTRON devices so it's a great extension for these devices. But you can use the mix controller also with your DAW like a classical 12-track-mixer.

The device has 24 standard pots, 12 Faders and 24 buttons in a 12-track-layout, various kinds of MIDI commands like control change, note on/off, pitchbend, aftertouch and program change are possible. You can program every MIDI command for every separate control on the device very fast and easily.

Of course you can assign the pots and keys to any of these commands by learning incoming MIDI commands, which is the same procedure you know from your software/DAW. The pots work with standard resolution of 7 bit to have full compatibility to any software and hardware instrument, effect and DAW. Use the internal 30 setups to save your individual settings. Backup and restore of all settings by sysex dumps is possible too.

The factory settings are perfect to control music and video software products out of the box if they are freely assignable. So any additional device programming isn't necessary for many applications.

Some special setups are preconfigured for use with ELEKTRON RYTM and ABLETON LIVE.

Check out this amazing power box and you will get a reliable mate...

Notes: More knobs than you can shake a stick at. Add hands-on control to pretty much any MIDI-equipped hardware or software. Upgraded version of the classic PC44, featuring a whopping 72 rotary pots and 12 buttons.

Supplier's notes:
PC12 as successor of the PC44 is a universal controller for all kinds of MIDI controllable hardware and software.

You can combine two or more NEW MODULE devices to create a large system. The connections are on the right side to allow a back to back placing of two or more devices. Connect two NEW MODULES by a special extension port.

Furthermore, there are 4 MIDI-ports and one USB-port with various routing possibilities.

It is packed in a metal case with the same dimensions like the famous ELEKTRON devices so it's a great extension for these devices. But you can use the pot controller also with your DAW like a classical 12-track-mixer.

The device has 72 standard pots and 12 buttons in a 12-track-layout, various kinds of MIDI commands like control change, note on/off, pitchbend, aftertouch and program change are possible. You can program every MIDI command for every separate control on the device very fast and easily.

Of course you can assign the pots and keys to any of these commands by learning incoming MIDI commands, which is the same procedure you know from your software/DAW. The pots work with standard resolution of 7 bit to have full compatibility to any software and hardware instrument, effect and DAW. Use the internal 30 setups to save your individual settings. Backup and restore of all settings by sysex dumps is possible too.

The factory settings are perfect to control music and video software products out of the box if they are freely assignable. So any additional device programming isn't necessary for many applications.

Some special setups are preconfigured for use with ELEKTRON RYTM and ABLETON LIVE.

Check out this amazing power box and you will get a reliable mate...

Notes: The BF-22 VCF is a dual Hi/Low-pass filter inspired by the Sallen-Key filter from the early MS-20.

DISCLAIMER: This filter brings to your modular system the character of early MS-20 sound: Kick-ass-rocking-dirty screams! It inherited not only it's amazing sound, also MS-20 noise floor. If noise floor is an issue for you, this might not be your filter.

Features:

Dual-channel Sallen-Key Filter. Inspired by the early MS-20
High and Lowpass operation.
Two CV inputs per channel with a dedicated atenuverter for the first one.
CV controlled resonance.
The first channel can be linked to the second one with the "Link" switch.

Specifications:

Current needs: +12V: 40mA, -12V: 20mA
Width: 17 HP
Depth: 30mm (including power connector)
Aluminiun, heat-treated front panel
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: The Sampling Modulator is a multi-function module that lies somewhere between a VCO, a Sample & Hold, and an 8 step trigger sequencer.

Sequencer Clocked Sample & Hold

In this mode it acts like a regular Sample and Hold (S&H) but since it is "sequencer clocked", it is capable of much more interesting patterns than the usual S&H melodies.

The CLOCK input can work in two ways: 1. As a typical clock 2. In "positive going hard sync" mode allowing you to create shuffling and polyrythmic effects.

The HOLD input can be used to keep certain notes playing.

Analog Down-Sampling Effect

In this mode (with the clock running at audio rates) you can go from nasty and harsh sampling rate reduction to an almost clean signal. (The clock run up to 25Khz without external CV and up to 200Khz with CV on the input).

Sampling Modulator/Shaper

Thanks to the V/Oct clock, by feeding a simple waveshape such as a sine wave to IN, and pitch CV to the VCO as well as to the Sampling Modulator CV input, their related frequencies and aliasing caused by the sampling rate reduction are capable of creating clangorous metallic sounds, 8 bit textures and much more.

The game becomes much more interesting when you try to destroy the wave by flipping on and off the switches of the sequencer (which at times can make it sound like three VCOs running in unison).

To understand how the Sampling Modulator works, keep in mind that we are working with a temperature compensated ramp core VCO with more than 4 octaves of tracking. This allows the timbre to stay the same while you move through the scale as the internal and external VCOs are synced in a fashion similar to "frequency related sampling rate modulation"

Unusual V/oct VCO You can use the trigger outputs as a pulse VCO. Flipping the switches on and off the switches can offer a lot of interesting timbral changes.

Notes: A four channel mixer, suitable for audio or control signals. It features regular and inverted outputs as well as an LED level meter.

Specifications:
Current needs: +12V: 21mA, -12V: 10mA
Width: 5 HP
Depth: 20mm (including power connector)
Aluminiun, heat-treated front panel.
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: Each of the two sections of the module is capable of performing the analog multiplication of two signals (A and B) and add an offset (C). It can also act as a dual voltage controlled attenuverter, dual ring modulator, dual VCA or four channel mixer (see block diagram below).

The B inputs are routed to an attenuverter that multiplies the signal between -2 to 2, while the offset inputs (C) route through a unity gain attenuverter (multiplies the signal between -1 and 1).

The output of first section is routed to the output of the second (when the first's output is unused), so the second output can act as master to achieve (A1*B1+C1) + (A2*B2+C2) or (A1 + C1) + (A2 + C2) - a 4 channel mixer.

The through-zero (four-quadrant) multipliers in the A*B+C allow for true Ring Modulation. To achieve this, simply connect two waveforms to the A and B inputs.

Notes: Crush Delay v3 is a special Echo-Delay unit based on the PT2399 IC, which is able to offer 400ms of clean delay and up to 2 seconds of dirty repetitions, having a special talent to generate noisy-glitch textures. The module bases its operation on controlling the PT2399 chip with circuit bending techniques, converting the unit in an advanced VC digital trash generator. This third version comes with some interesting new features like redesigned VCAs circuits, wider range for clean delay and reduced depth to make it skiff friendly.

The module features a few VCAs to provide a flexible signal route to maximize module's possibilities. First two VCAs at the inputs to control the amount of signal sent to the delay. The first is routed to both the dry/wet mix and the delay, and the second directly to the delay. Combining the second VCA and the FX Send output allows external feedback routings.

Compared with v2, this third version offers a bigger range of clean delay time as well as a revision of some of the Crush modifiers. Combining those modifiers you will have a access to a vast palette of noises and textures that can be used in many different ways. From ambient/drone patches to even percussion sounds.

The VC Feedback features an automatic gain control to keep levels stable at any feedback level.

- Current needs: +12V: 135mA, -12V: 35mA
- Width: 11 HP
- Depth: 30 mm (inc power connector)
- Aluminium, heat-treated front panel
- Designed, kits prepared and modules assembled in Barcelona

Notes: A compact attenuverting (attenuator-inverter) joystick controller and Gate Generator. With it, you can generate and process two control voltages using only one hand. Provided controls for CV ranges and offset adjust the boundaries of your control, this way it never gets out of the desired range, ensuring sensibility and playability even with wild performance gestures.

Specifications

Current needs: +12V: 25mA, -12V: 10mA
Width: 12 HP
Depth: 35mm (including power connector)
Aluminium, heat-treated front panel.
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: Pack of high Quality patch cables. Not too stiff, not too loose!

One colour for each size make Befaco patch cables just perfect to keep them organized!

This pack contains 6 high quality purple patch cables.

Notes: Pack of high Quality patch cables. Not too stiff, not too loose!

One colour for each size make Befaco patch cables just perfect to keep them organized!

This pack contains 5 high quality black patch cables.

Notes: Pack of high Quality patch cables. Not too stiff, not too loose!

One colour for each size make Befaco patch cables just perfect to keep them organized!

This pack contains 3 high quality blue patch cables.

Notes: Pack of high Quality patch cables. Not too stiff, not too loose!

One colour for each size make Befaco patch cables just perfect to keep them organized!

This pack contains 3 high quality green patch cables.

Notes: With these power split cables, it is easy to distribute the power from an AD-9 to more than one pedal.

The new design introduces flat contacts (similar to the popular EBS flat patch cables) to further reduce space on your pedalboard.

Notes: One to four configuration.

With these power split cables, it is easy to distribute the power from an AD-9 to more than one pedal.

The new design introduces flat contacts (similar to the popular EBS flat patch cables) to further reduce space on your pedalboard.

Notes: Hopscotch Patch Cables are the perfect solution for modular synthesizers equipped with mono mini jacks. The pigtail mono mini jack gives users the ability to "jump" the signal to another input point while keeping the original patch intact. Features include:

- Easy-access pigtail jack for quick signal splitting
- Slim housings to fit crowded spaces
- Nickel-plated plugs for rugged durability and efficient signal transfer

Connectors: 3.5 mm TS with 3.5 mm TSF Pigtail to 3.5 mm TS
Conductor: 26 AWG OFC
Shield: 85% OFC Spiral
Quantity: 5 pc

Notes: These cables are designed to interconnect pro audio gear with unbalanced mini phone jacks. They are ideal for use with modular synthesizers and sound modules.

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Connectors: 3.5 mm TS to Same
Conductor: 26 AWG OFC
Shield: 85% OFC Spiral
Quantity: 8 pc

Notes: These cables are designed to interconnect pro audio gear with unbalanced mini phone jacks. They are ideal for use with modular synthesizers and sound modules.

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Connectors: 3.5 mm TS to Same
Conductor: 26 AWG OFC
Shield: 85% OFC Spiral
Quantity: 8 pc

Notes: These cables are designed to interconnect pro audio gear with balanced phone jacks. They are ideal for use with balanced phone patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Connectors: 1/4 in TRS to Same
Conductors: 26 AWG x 2 OFC
Shield: 85% OFC Spiral
Quantity: 8 pc

Notes: These cables are designed to interconnect pro audio gear with balanced phone jacks. They are ideal for use with balanced phone patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Connectors: 1/4 in TRS to Same
Conductors: 26 AWG x 2 OFC
Shield: 85% OFC Spiral
Quantity: 8 pc

Notes: These cables are designed to interconnect pro audio gear with balanced phone jacks. They are ideal for use with balanced phone patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Connectors: 1/4 in TRS to Same
Conductors: 26 AWG x 2 OFC
Shield: 85% OFC Spiral
Quantity: 8 pc

Notes: Module A-147-2 is the successor of the VCLFO A-147 but offers much more features than the predecessor. The module is made of these sub-units:

- VCLFO: voltage controlled low frequency oscillator
- VCA: voltage controlled amplifier, switchable to voltage controlled polarizer
- VC delay unit: voltage controlled linear attack envelope (only one parameter: attack) for delayed LFO operation in combination with the VCA (e.g. delayed vibrato/tremolo)

LFO: The voltage controlled LFO has the waveforms Triangle, Sine, Sawtooth and Rectangle available and features a Reset/Sync input. Triangle/Sine and Rectangle are displayed by means of dual-colour LEDs (probably red/green), Sawtooth has a unicolor LED available (probably blue). The output levels are about -4V...+4V for Triangle, Sine and Rectangle. The Sawtooth level is about 0...+8V.

The CV control can be switched to attenuator or polarizer ("CV Mode" switch). In polarizer mode the CV inputs affects the frequency in the reverse manner when the CV control is left from the centre position. In the centre position CV has no effect and right from the centre the control works like a normal attenuator. The frequency range (without external CV) is from about 0,005 Hz (i.e. about 3 minutes per period) to 200 Hz (with external CV max. frequency about 1kHz). In addition a ultra-low mode can be activated by means of an internal jumper. When the ultra-low jumper is set a fixed voltage is connected to the switching contact of the "LFO CV" socket. In polarizer mode of the CV control that way extremely low frequencies (up to one hour period and more) are possible. For this a jumper has to be installed on the pin header JP6. In the factory a dummy jumper is installed on the pin header JP7 "Dummy". JP7 has no function and is used only for "parking" of the jumper. Simply remove the jumper from JP7 and plug it on JP6. JP6 is located behind the CV control.

VCA: This is a linear VCA that can be switched to "normal" VCA (i.e. kind of a voltage controlled attenuator) or voltage controlled polarizer ("VCA Mode" switch). In the "normal" VCA mode amplification +1 is achieved with about +5V control voltage. In polarizer mode the amplification ranges from about -0.5 (i.e. inverted signal with about 50% level) with 0V CV to +0.5 (i.e. non-inverted signal with about 50% level) with +5V CV. With about +2.5V CV the signal is suppressed. Details about the functioning of a voltage controlled polarizer can be found in the description of the module A-133. In this mode the VCA can be treated also a DC coupled ring modulator (similar to A-114).

The VCA of the A-147-2 has three sockets available: "In" (signal input), "Out" (signal output) and "CV" (control voltage input).

The Triangle Output of the LFO is normalled to the VCA signal input by means of the switching contact of the "VCA In" socket. If another LFO waveform (or any other signal) should be processed by the VCA the corresponding signal has to be patched to the "VCA In" socket. The VCA can be used also independently from the LFO and the Delay CV. In this case the VCA sockets In, Out and CV have to be patched accordingly. The VCA can be used also as waveshaper for the LFO signals (e.g. by patching VCA In and VCA CV to different LFO signals, if necessary via attenuator A-183-1 or offset generator/attenuator A-183-2).

Attack/Delay: The third sub-unit of the module is a simple, voltage controlled envelope generator that has only the parameter "Delay" (or Attack) available. This unit generates a linear increasing voltage that starts from 0V after each Delay Reset until it reaches about +5V. Then the voltage remains at +5V until the next Delay Reset occurs. The inclination or gradient is controlled by the manual Delay control and the Delay control voltage ("Delay CV" input). The waveform is linear, the control scale is exponential. The output voltage is displayed by a green LED and available at the "Delay Out" socket.

The manual Delay control ranges - without external "Delay CV" - from about 5ms (fully CW) up to 2 minutes (fully CCW). By means of an external voltage applied to the "Delay CV" socket this range can be extended. A rising CV shortens the delay time (behaviour like a VCO)!

The Delay output voltage ranges from about 0V to +5V. The rising edge of the gate, clock or trigger signal applied to the "Delay Reset" sockets resets the Delay output voltage to 0 V.

"Delay Out" is normalled to the VCA CV input by means of the switching contact of the "VCA CV" socket and consequently controls the Triangle level provided that no other patch is made. A typical example is the usage of a Gate signal (e.g. from a USB/Midi-to-CV/Gate interface) as Delay Reset. That way a delayed vibrato or tremolo can be realized if the VCA output is patched to the frequency CV input of a VCO (or VCF), or the CV input of a VCA.

Notes: A-138s is a simple but useful 4-in-2 mixing tool. It has four inputs available. Each input is equipped with an attenuator (Level) and a panning control that is used to distribute the signal to the left and right output. Beyond stereo mixing it is equally suited to create variable parallel routings. For example: Any of the four inputs may be routed in variable intensity to feed two filters.

You may regard the A-138s as a smaller version of the A-138m Matrix Mixer.

Inputs and outputs are DC coupled, i.e. the module can be used for the mixing of control signals too.

- 3U Eurorack module, 8 HP wide, 30 mm in depth
- Power consumption: 10 mA at +12 V and 10 mA at -12 V

Notes: Module A-112 is the combination of a voltage controlled 8 Bit Sampler and a wavetable oscillator. On top of it the module is able to generate some special effects. A-112 was designed as an additional sound source with the typical sounds of the early 8 bit samplers and is not comparable with the modern polyphonic MIDI samplers available on the market.

Sampling mode: 8 bit audio resolution, 128kB memory in 2 banks 64kB each (equivalent to 2 seconds of sampling time for each bank with 32 kHz sampling rate), audio input with attenuator, overload display in record mode (gate LED), possibility of MIDI Dump to store sounds in a computer via MIDI, non-volatile memory for the 2 samples in the module, manual tune control for adjustment of sampling rate for record and play, CV input (~ 1V/Oct), both manual tune and CV determine the sampling rate respectively the pitch (pitch range is 5 octaves), gate input (not a trigger: the sample starts at the positive edge of the gate signal and is played as long as gate is high or until the end of the sample is reached), manual Gate button, non-filtered audio output (thus quantizing noise can be used as an element of the sound intentionally).

Wavetable mode: special appearance of the sampling mode when playing a sample, the audio input is now used as a second control voltage input for moving through the sample in 256 byte wide loops (wavetables). The control voltage required to move through all wavetables applied to the input "Wave CV In" is in the range -2.5V (wavetable 1) ... 0V (wavetable 127) ... +2.5V (wavetable 256) when control "Atten." is set fully clockwise. To achieve the typical wavetable oscillator sounds the sampling memory must contain corresponding wavetable data (e.g. loaded via MIDI dump). These data contain a set of wavetables with different harmonic content (e.g. a filter sweep) to get the typical wavetable sound while moving through the tables via CV. But you may also use a "normal" sample and go through the sample with CV to obtain partially amazing sounds never heard before. You may use for example sampled speech and go with CV through the syllables or speech shreds to get really very extreme sounds. An ideal addition for this feature is the Offset/Attenuator module A-183-2 which can be used to adjust the position of the wavetable (Offset) and the modulation depth (Att.). The corresponding jumper of the A-183-2 has to be set to bipolar offset (as the A-112 requires -2.5V...+2.5V to pass through all 256 wavetables). As modulation source an LFO (A-145, A-146, A-147, A-143-3), ADSR (A-140, A-141, A-142, A-143-1/2) or a random voltage (A-118, A-149-1) may be used. Even a ribbon controller (A-198 or R2M), the Theremin module A-178, the Joystick A-174 or the Wheels module A-174-2 are useful to drive through the wavetables.

Effects: Additionally, the module offers - in a way free of charge - some effects like delay, reverse delay, pitch shifting or freeze. But it has to be pointed out that due to the 8 bit audio resolution these effects are not comparable to high quality effect units and should be understand as an extra for nothing. The A-112 is not an effects unit!

The sampling time of the A-112 is about 1...30 seconds corresponding to a sampling frequency range of about 60kHz...2kHz (64kB@60kHz ~ 1 s, 64kB@2kHz ~ 30 s).

Technical note: the module uses a battery for the non-volatile storage of the sampling data. Batteries have a limited lifespan and have to be inspected at least every two years. For details please refer to the FAQ page of our website: Lifespan of rechargeable batteries (used for memory backup).

Notes: Tallin is a dual voltage controlled amplifier (VCA) with overdrive, offering some unusual control features and a range of attractive tonal characteristics. Each of the two identical channels offers two simultaneously available inputs for voltage control over signal attenuation or gain, with linear and exponential response to CV. Volume control knobs offer manual gain settings ranging from fully closed (-80dB) up to +18dB. A colour LED indicator displays output signal levels. A soft-clip circuit avoids harsh clipping distortion, while a switchable overdrive circuit offers two carefully crafted distortion responses, simulating the sound of classic tube amplifiers.

Since both CV inputs are simultaneously active, they can be jointly exploited within patches featuring more complex volume control that otherwise would require using two traditional VCAs in series. As the signal path is DC-coupled, Tallin can also be used for handling the control voltages.

Notes: Module A-148 (Dual S&H) has two identical sample & hold modules, designed to produce 'staircase' voltages. The signal present at the sample input is sampled at a rate set by the signal at the trigger input, and held at that voltage at the S&H output.

The exact shape of the staircase depends on the sort of waveform at the sample input: NOISE or RANDOM signals produce random patterns; an LFO produces rising or falling staircase patterns.

Two LEDs for each S&H indicate the voltage (positive or negative) of the sampled signal.

Notes: The SAPEL is a random control voltages source for Eurorack modular systems. It is composed of two main sections, one that generates audio noises, in 4 different versions, and another which includes two specular random clock, random voltages and clock sources.

Noise outputs are colour coded, based on the noise colours, and include:

- Blue (+3dB/oct spectrum)
- White noise (0dB/oct spectrum)
- Pink noise (-3dB/oct spectrum)
- Red noise, a.k.a. Brown or Brownian (-6dB/oct spectrum).

The random voltage and clock section features four uncorrelated random CV generation paths, divided in;

- Fluctuating random voltage;
- Quantized random voltage with 2n stages tuned in semitones referred to 1V/oct scale;
- Quantized random voltage with n+1 stages tuned in octaves referred to 1V/oct scale;
- Non quantized sample & hold.

It is also possible to set a probability distribution with a potentiometer, and apply (or do not apply) the chosen distribution setting to each of the four paths independently.

Furthermore, each of the two random sources section features an independent built-in clock generator, with clock output and random clock output, which can be used in "more than" or "less than" mode. It is possible to use an external clock signal as a clock source, bypassing the built-in one. In addition to that, it is also possible to hand trigger the clock via a manual sample & hold button, which can be also modulated by gate signals.

Notes: The FUMANA is an all analog dual filter bank with various control to access dynamically these bands. Each filter bank is composed of an array of 16 independent 48dB/oct bandpass filters. Having two identical filter arrays, allows you to use one of those for spectral analysis (of a modulator signal) and the other for spectral re-synthesis (of the main signal). Each array is sub-grouped in odd and even bands (numbering these increasingly from 1 to 16 from left to right). It is possible to apply different signal to odd and even bands, both for main and/or modulator arrays. This, together with the 16 envelope followers connected to each band of the modulator filterbank, and the 16 VCA connected to each band of the main filterbank, allows the FUMANA to perform a single 16 bands or a dual 8 bands analog spectral transfer.

While the upper section provide access to each main filter's direct output, the lower section has 4 voltage controllable parameters to manage two independent functions for further spectral editing: tilt and parametric scan.

The tilt, as the name suggest, tilts the spectrum, adding and subtracting amplitude to the 16 bands, emphasizing lower or high bands, and attenuating high or lower bands: this is managed only with the green potentiometer.

The parametric scan, instead, works with three parameters: peak/notch, band selector and width. Like in a parametric equalizer, where is possible to set peak/notch gain, frequency and slope, the FUMANA uses three parameters to set which is the centre band to perform this manipulation, then if that band should be emphasized or attenuated, and how this action is extended to nearby bands.

In addition to the 16 bandpass outputs, there are other 4 outputs provided: the all bands output, the all envelope followers output, the odd bands and the even bands output. These two have the options to be inverted in phase with two switches, in order to obtain even more combination when summed together, maybe/also with the "all bands output", using, for example the 333 module.

Since a spectral transfer tool may be used as a "vocoder-like-effect", the FUMANA provides an input for an external noise which may be used for unvoiced (fricative/sibilants) sounds as words containing or starting with s, f, z, ch and other fricative sounds.

Notes: The 333 is a summing and distribution module for Eurorack modular systems.

It is composed of three identical sections, the red, yellow and green, each of those featuring three inputs summing amplifier with three independently buffered outputs.

Derived directly from the CGM creative mixer series, the sum section is DC coupled, allowing the sum of control voltages as well as audio signals.

With an extremely low tolerance in both sum and output sections, it is suitable also for summing quantized voltages like the ones coming out from the quantized outputs of the SAPEL.

In case CVs or audio signals are particularly hot, the 6dB attenuator might be helpful to reduce exactly by 50% the incoming signals.

Red and yellow output are also normalled to the 1st jack socket of the yellow and green input: in this way this module can also work as a 1 to 9 buffered multiple.

Notes: The 321 includes the most useful functions we always need in every patch, to edit and combine dynamically the signals in use.

It is composed of three identical sections, the red, yellow and green, where each of those is capable of scaling any signal, from 0 up to 2 times (+6dB), flip its phase, and apply a DC offset, allowing to shift your audio or CV up or down.

In case no signals are connected to the section input, the offset may act as a CV source too.

The three sections are then summed together into two independent summing stages: the top right jack outputs the sum of all three sections, while the top left outputs the sum of the unconnected sections only (semi-normalled).

The 321 is entirely DC coupled, allowing the process of control voltages as well as audio signals.

In case CV's or audio signals are particularly hot, the two 6dB attenuators, one per each summing section might be helpful to reduce exactly by 50% the incoming signals.

Notes: High quality audio leads for exceptional sound quality and reliability. High grade cable comprises an insulated pure copper core and global shielding.

The durable PVC sheath has a soft texture and is reinforced with cotton cord to avoid tangling. Terminated at one end with a 6.3mm stereo (TRS) jack plug and at the other end with a male XLR connector.

Notes: This module connects via 3 pin cable to the Intellijel Pedal I/O 1U module.

It provides the 1/4" TS interface for connecting guitar pedals or instruments.

Dimensions: 8 HP
44 mm deep

Module is a 1U tile.

Current Draw: Module does not draw current

Notes: The Pedal I/O JACKS 1U Module allows you to patch standard 1/4? TS cables to and from your guitar/instrument pedals.

This module only works when connected to a Pedal I/O 1U module via ribbon cable.

Notes: This module allows you to connect balanced line level audio (+4 dBu) into your Eurorack modular system. It is a compact and easy way to patch in a rack mount/desktop FX units, external line-level instruments like synths and drum machines, outputs from your DAW, or many other line level sources.

Notes: Not plastic, metal. No muffled, mids-centric sound but tight low mids and present treble. No problem with feedback, spill or handling noise; instead, maximum flexibility for the voice: the e 835 is a solid choice for performers. Moderation and singing remain crystal clear and natural, even at varying distances from the capsule. Its extremely rugged construction and uncomplicated handling make the e 835 the first choice for rehearsal rooms, home recording or the stage. It has also become a top seller in its class everywhere that speech intelligibility is critical: lectures, presentations or conferences in auditoriums large and small alike.

Dynamic cardioid microphone for speech and vocals

Cuts through high on-stage levels

Clear reproduction with a high presence

Consistent sound quality (varying distances, moving off axis)

Handles high sound pressure levels

Optional silent on/off switch

Isolates handling noise, hum compensating coil

Excellent feedback rejection

Rugged metal housing

Specifications

Dimensions: O 48 x 180 mm
Connector: XLR-3
Frequency response (Microphone): 40 - 16000 Hz
Transducer principle (Microphone): dynamic
Weight: 330 g
Pick-up pattern: cardioid
Sensitivity in free field, no load (1kHz): 2,7 mV/Pa
Nominal impedance: 350 O
Min. terminating impedance: 1000 O
Weight w/o cable: 330 g

What's in the Box:
1 e 835
1 microphone clip
1 pouch

Notes: Dynamic super-cardioid vocal mic, which helps to reduce spill and feedback. Ideal for presentations, conferences, choirs, rehearsal rooms, and stage. Easily eliminates ambient noise. Superb high frequency reproduction.

More focus. More presence:

Maximum focus, enhanced presence: the E845 delivers differences you can hear. Its expanded high frequency range creates space for demanding dynamics with a high signal quality. Vocals become more alive and sound wider and more open - even at different speaking proximities. Designed as a super-cardioid, the E845 easily eliminates ambient noise. A reliable, easy-to-use companion for presentations, conferences, spoken word performance, choirs as well as rehearsal rooms and on stage.

In the box:

1 x E845
1 x Microphone Clip
1 x Pouch

Notes: Samson introduces the new UB1 USB boundary microphone. The UB1 is a surface-mount condenser microphone featuring an omni-directional pickup pattern and USB connectivity for easy recording directly to your computer. Since the UB1 is a class compliant USB device, it is compatible with both Mac OS and Windows.

The UB1 can be placed on a conference table, podium, alter or can be mounted using the keyhole mounting points. Because of its low-profile design, the UB1 allows for inconspicuous placement in any setting and will offer professional-grade recordings on either a desktop or laptop computer. The solid zinc body and sturdy steel grill construction make the UB1 a dependable tool for conference rooms, houses of worship, courtrooms, classrooms or anywhere else high quality computer recording is needed.

Notes: The S-Com 4 is a compact and versatile single-rack space device that provides four channels of high-quality dynamic processing with an Expander/Gate and Compressor/Limiter on each channel.

The four channels operate independently or in stereo pairs. Its multi-segment LED metering displays input/output level as well as gain reduction. The Expander/Gate section features a continuously variable Threshold control, as well as a switch for fast or slow release times. The Compressor/Limiter section includes variable Threshold, Ratio and Output levels. S-Com 4's Enhancer switch restores high frequencies that are sometimes diminished by heavy compression.

This wide-ranging combination of features makes the S-Com 4 an efficient and versatile audio tool for a wide variety of applications. Its clean and quiet audio characteristics make it ideal where high sonic integrity is imperative.

Notes: Gorgeous retro-inspired synth. Heavily based on 70s string synthesisers and vocoders, updated in a modern format. Proper lush vibes.

Supplier's notes:
The string section starts with an oscillator bank using octave dividers, followed by a complex mixer, an equalizer and the ensemble effect, just like string machines from the 70's. A single registration knob sweeps through mixer and EQ settings for Violin, Viola, Cello, Brass, Organ, Choir and more for creating rich and creamy sonic textures.

The Solo section is a 16-voice synthesizer that complements the string sounds. A single Tone knob sweeps through many useful settings. Solo is the sidekick to the strings, but it is powerful enough to be the lead character every now and then.

The Vocoder replaces the equalizer in the string section with the filter bank that models the vocal tract from the speech input. This can produce quite intelligible speech or singing using the fully polyphonic oscillator bank. Formants can be modified, which can result in a perceived change of gender. Adjustable jitter of the string oscillators renders the voice hoarse, creaky or a complete whisper. Solo can pass through the Vocoder or play in parallel.

The Freeze button lets you freeze a short speech fragment, which is then repeated by the Vocoder whenever a key is pressed. Change of playback speed, like faster, backwards or a complete stop are possible and fun, as well as formant change.

A novel Tweak function allows for modification or modulation of details, like e.g. the solo cut-off frequency or the Chorus LFO rate. It is similar to a modulation matrix, but it also allows to alter implicit settings with a fixed value or an offset.

Three Effects operate simultaneously - Animate is in fact a modulation of the string or vocoder registration, while a Phaser is a must for any decent string machine. A high-quality Reverb with adjustable size can be mixed to the output.

STVC comes with a high-quality gooseneck microphone that plugs right into the front panel where it belongs.

Notes: The Volca Mix is a four-channel analogue performance mixer that lets you construct a live setup combining multiple Volca units.

Volume faders are easy to control, plus crisp-sounding LO/HI CUT filters, and a master chain that radically transforms the sound. In addition to the sync function found on all Volcas, there are also DC output connectors that can supply power for up to three Volca units. Numerous functions to facilitate your on-stage Volca performances have been packed into a high-quality aluminium-panelled body, reminiscent of a high-end DJ mixer. The Volca Mix will unlock the maximum potential of the Volca series.

An analog mixer for performance:

The Volca Mix is a four-channel analog mixer with an intuitive interface and plenty of connectivity. It provides two mono inputs and one stereo input, perfect for connecting three Volca units. The jacks are mini-jacks, allowing you to make connections with just one stereo mini-cable from the headphone out of each Volca unit. The channel volumes use vertical faders that allow precise control. The gain can be boosted to adjust the mix balance, and mute buttons are also provided. Each channel is also equipped with a LO/HI CUT filter that lets you control the low and high frequency ranges with a single knob. The pristine, natural-sounding filters that you expect from analog gear give you complete control over the character of your sound.

Output and monitor capabilities for use on stage, plus stereo speakers for maximum portability:

The output section provides RCA stereo line outputs to ensure stable connection. There's a master volume with LED VU meter for adjusting the output level, as well as a headphone output that can be used simultaneously with the line output, providing a reliable monitoring environment on stage. Speakers are also built-in for excellent portability. The stereo speakers are placed at both sides of the front, and while compact, deliver SPL levels that are even greater than the built-in speakers on previous Volca units.

Powerful master chain:

The Volca Mix is equipped with master effects powered by all-analog circuitry. In addition to an expander that broadens a mono source into a stereo sound image, there's a dynamic range compressor that compresses the high-frequency range according to level changes of the low-frequency region, as well as a side chain effect that's indispensable for dance music. Use these to dynamically vary the mix, adding a professional feel to live performances with the Volca.

Connect an external effect unit for further variety:

The Volca Mix provides a stereo mini-jack send out and AUX in jack, and send level knobs for each channel. This allows you to use it with an external effect unit in a send/return connection. When used in conjunction with a unit such as the mini Kaoss pad 2S, you can also enhance your live performances using standard effects such as reverb, delay, filter, and break. The AUX in jack can also be used as a stereo input channel for a fourth Volca unit, an iOS app, or any other gadget, instrument, or device.

As the master of your Volca live setup:

The Volca Mix features an analog sync out jack that can easily be connected to many pieces of KORG gear for tempo sync, and also a play button and tempo knob to control that sync signal. By using the Volca Mix as the sync master device of your live setup, you can easily enhance your live performance, such as simultaneously playing sequences from multiple synced units, and combining mute and volume control to create performances that use your Volca units in even more ingenious ways.

Notes: The CA-50 features high-precision tuning functionality and a slim and compact design. The new CA-50's display is now, even easier to read. Long considered the standard in chromatic tuners, the CA-50 offers simple and intuitive operation and a satisfying tuning experience for every instrumentalist.

The LCD screen of the CA-50 shows a needle-type meter to quickly and accurately show the pitch, and provides a note name indication in the middle of the display. The note name indication is now larger and even easier to read. This ensures simple and smooth operation even for beginners.

The CA-50 features a detection range of A0 (27.50 Hz) to C8 (4186.01 Hz). For wind instruments from piccolo to tuba, or string instruments from violin to contrabass, you can tune band or orchestral instruments of any pitch range. A high-sensitivity mic is built in, allowing the note name to be detected accurately even without a contact mic. By using the separately sold CM-200 contact mic, you can tune with confidence that nearby sounds will not affect the result.

The calibration function supports a variety of concert pitches. It can be adjusted in 1 Hz units in the range 410-480 Hz, allowing flexible tuning that matches the song or key.

The meter scale of the CA-50 provides marks that indicate pure major and minor third intervals. By tuning to these marks you can play beautiful harmonies when you're in an ensemble. This is convenient not only in a brass band or orchestra, but also for vocal or a cappella practice.

The "Sound Out" mode lets you listen to a reference tone emitted by the internal speaker, allowing you to tune by ear. A reference tone in the range of C4 (261.63 Hz) to C5 (523.25 Hz) can be output. You can check the pitch using both eye and ear, allowing you to tune more accurately, and also providing an ideal method of training your sense of pitch.

The CA-50 can be used for approximately 135 hours (when using zinc-carbon batteries). When the remaining battery capacity runs low, the display shows an indicator, letting you know that it's time to replace the batteries.

A new mechanism reduces the possibility that the unit will overturn, making it less likely that the tuner will slide off and fall when placed on a music stand. You'll be able to concentrate on your playing without fearing that the tuner might fall during the performance.

The memory backup function remembers the calibration and sound out mode settings even when the power is turned off. (Settings are initialized when you replace the batteries.) The auto power off function automatically turns off the power when 20 minutes have passed without sound being input.

The folding stand allows the tuner unit to be more stable on its own. The sliding battery cover is designed as a single piece with the unit itself, so there's no worry that the cover might be lost when replacing the batteries.

Notes: ***Now featuring Assimil8or Software Version 2.0! Available to download here: http://www.rossum-electro.com/products/assimil8or/

The ASSIMIL8OR is a CV/Gate-controllable sampler with eight independent channels. Each channel is not only its own voice, but also has a separate audio output and a gate/trigger and three CV inputs. Given ever get two sample inputs and main outputs. Thus, Stereo Sampling and playback is possible. Mixed operation of stereo or mono is possible and is limited only by the maximum number of eight channels or parts.

The ASSIMIL8OR works with high-quality 24-bit AD and DA converters. Internally, however, sample and bit rate for lo-fi sound can be lowered, the latter is even CV-controllable. The samples can also be otherwise manipulated in many ways. Thus, the phase of a sample via CV or a different sample can be modulated. Likewise, the loop points can be controlled and the sample can be traversed with CV control (scrubbing), whereby wavetable similar effects could be achieved. The following parameters can be addressed via the gate / trigger and CV inputs:

- Pitch
- Level
- Bit Depth
- Phase Modulation
- Pan
- Scrub
- Sample Start
- Sample Length
- Loop Start
- Loop Length
- Release Decay

Samples and presets are stored on an SD card, which is easily accessible plugged into the module front.

Notes: Sewastopol is a multifunction Eurorack module designed for easy interfacing of external gear to your modular environment. It can export line and professional level audio, import audio from instruments and electroacoustic transducers, and analyse the incoming audio to generate voltages and triggers to control your modular system.

This is a second, vastly improved revision to the original 2014 Sewastopol, featuring a completely redesigned preamplifier circuit, better ergonomics and various other improvements.

Notes: Clep Diaz is a handy and small step CV and LFO generator. In step and random modes, use the encoder to control the number of steps in the sequence; in LFO mode, the encoder controls the amplitude of the wave. Toggle the directionality of the sequence: up, down, or up/down to customize the CVs further. CD also gives CV control over the number of steps in the sequence and an end-of-cycle trigger output. Unipolar and bipolar outputs allow maximal control.

Notes: Hat is a hi-hat cymbal with a wild side. Finding something unique is easy with a blend of sounds ranging from robotic to metallic. At its core are three unique sound sources made up of six oscillators, a noise generator, and a number of filters. Sizzle affects each source independently, adjusting oscillator and filter frequencies, allowing for a broad range of sounds. In addition, separate trigger inputs for open and closed allow for a complete hi-hat pattern on a single module. No matter what situation it's in, Hat provides shimmering, metallic timbres for any percussive purpose.

Notes: The Tapographic Delay is a complex multi-tap delay in the Eurorack format with a unique interface designed for live performance. It excels at transforming the simplest audio (a drone, a percussive sound) into complex rhythmic structures, meshes of organic textures, lush harmonic mille-feuilles, liquid and resonant effects.

Have you ever got tired of the monotonous repetitions that your standard delay pedal/module produced? Have you ever wished for a more complex rhythmic structure than just decaying repetition? If yes, you have come to the right place: the Tapographic Delay is an advanced effect that lets you handle repetition in a completely novel way. It is to a traditional delay what a full rhythmic sequencer (with pattern recall, velocity control, tactile input) is to a simple clock. With the TD, you interactively define the rhythm that the repetitions will follow: a velocity-sensitive sensor allows you to record, edit, modify, and sequence your own arrangements of delays. In a sense, the TD is the converse of the classic Frippertronics sound-on-sound setup popularized by Robert Fripp in the 70's: you don't play the guitar, you play the tape loop!

The Tapographic Delay is an expressive experimental instrument meant to be played in real-time, rather than a set-and-forget end-of-chain effect. Interact with it! Experiment! Push it to its limits!

Notes: Listen Professional circum-aural closed back headphones are the essential work tool for music production. Their tonal balance and precision in terms of audio spectrum make them perfect to evaluate the sound work quality. In addition, their comfort and accessories will make them very attractive for people travelling on business trips. The sound quality and the dynamics of these headphones are very surprising considering that this quality is usually found on more expensive items. The attention to detail of these headphones can be also shown thanks to the various patents and technologies which belong to Focal. Hence, a brand-new driver membrane was developed. The main goal was to propose a solution which would keep all the dynamics from the original track while reproducing accurately every single detail on the whole audio spectrum. Even if Listen Professional headphones are closed, they produce a very lively sound, giving the feeling of semi-open headphones while still providing the isolation of closed headphones.

Focal's core expertise:

The speaker driver has been given a 100% Mylar suspension, whereas the central dome is composed of a Mylar-titanium alloy to provide more rigidity and extended frequency response in the upper end of the spectrum. Thus, the moving part is extremely light, enabling the transducer to exceed 40kHz on a flat baffle. The reproduction of the bass and sub-bass registers also received a great deal of attention. The team of engineers managed to combine two factors which are hardly compatible: a tuning frequency which is as low as possible and extremely low distortion (0.3% at 1kHz - 100dB).

Ear cushions - the ideal acoustics:

The size of the ear cushions (height, width and depth) gives them a volume which makes it possible to achieve a great tonal balance. Microfiber provides a more linear bass response providing a better acoustic output, whereas the acoustic tissue, which is closer to the speaker driver, offers great absorption and linearity in the 3-9kHz register. The bass and lower mid-range sections benefit from remarkable tonal balance and excellent articulation: where compression and frequency response generally suffer on closed-back headphones.

For a frequent and intensive use:

Listen Professional is also equipped with a headband boasting a unique design to ensure comfort and durability. Its curve remains consistent, regardless of the shape or size of the user's head. Combined with the layer of silicone underneath the headband, this ensures that the weight is spread out evenly over the head, preventing the user from feeling any pressure in certain areas, which can be very uncomfortable during long working sessions. The horizontal and vertical rotation of the ear cups operate thanks to one single part: a joint integrated into each one. The ear cups also feature a black structured covering, making them resistant to impacts and scratching.

Provided Accessories:

Rigid carrying case. Thermoformed shell in the shape of the headphones. Can store one cable and an iLok key (not provided), all within its compact dimensions. Two OFC copper 24AWG cables with a very low resistance.

- 5m spiral for domestic use
- 1.2m cable fitted with a 3.5mm stereo jack connector
- 3.5mm and 6.35mm jack adapter

Notes: Perfect for adding that final touch to a modular patch, the AJHSynth Finaliser R-EQ module includes seven Mono / Stereo reverb types, along with a four band equaliser and a Sonic Maximiser / Enhancer.

The Reverb, EQ and Maximiser can be used in Mono IN, Mono OUT mode or Mono IN, Stereo OUT modes. The reverb alone can also be used in Stereo IN / Stereo OUT mode too.

The fully analogue four band Equaliser includes three parametric equalisers for Low, Low Mid and High Mid ranges, and the High EQ has switchable shelving of either 2kHz or 5kHz. The Low EQ also includes a shelving mode.

The Maximiser is a fully analogue circuit too, with low and high treatment bands which change the phase and amplitude relationships of the sound to add punch and harmonics and really bring the sound to life in the mix.

The Reverb engine is based on 20 year old DSP technology, harking back to the reverb units which were used extensively on many synth and EDM tracks a couple of decades ago. We have added full control of reverb wet / dry mix, either manually or under CV control.

Notes: Excellent Eurorack sequencer based on random chance and evolving patterns. Dial in a series of notes and build melodies, generate and tweak patterns in real time. Huge depth for studio production or live performance.

Supplier's Notes:
The Melodicer from Vermona is a CV/Gate sequencer with an innovative concept; the melody sequencer offers twelve faders for setting the note probability and two dice-(or random) buttons for generating melody and rhythmic structure.