Search dance music

Notes: ADSR is a four stage linear envelope with two expressive ranges. Each stage can be modified independently allowing for the creation of complex, multi-segment envelopes. Great for modulating filters, VCAs, and oscillators.

Notes: Arp is a gate-driven arpeggiator with a multitude of chord types and playback modes. Voltage control over both root note and chord type allow for sequencing any combination of chords in any key imaginable.

With the rate of the arpeggio and reset capability in your own hands, you're free to create dynamic rhythmic melodies from your favourite chords. Take your tonality for a ride with Arp.

Notes: Delay is a flexible, full-featured delay audio processor. CV over all parameters provides dynamic access to its nuanced controls. The feedback path ranges from slapback to infinity, allowing for wild permutations of the original signal.

With delay times from milliseconds to nearly two seconds, Delay is sure to find a use in every patching situation. Add subtle echo to a melodic line, or crank up the feedback and hear a bed of layered sounds to bury your listeners in.

Notes: Div is a 2 channel, voltage controlled clock divider and multiplier. Incoming clock signals can be multiplied or divided by a factor of 16 with a multitude of values in between.

CV inputs provide external control of the current clock rate, allowing for the creation of dynamic rhythms from a single clock signal.

Notes: Hat is a hi-hat cymbal with a wild side. Finding something unique is easy with a blend of sounds ranging from robotic to metallic. At its core are three unique sound sources made up of six oscillators, a noise generator, and a number of filters. Sizzle affects each source independently, adjusting oscillator and filter frequencies, allowing for a broad range of sounds. In addition, separate trigger inputs for open and closed allow for a complete hi-hat pattern on a single module. No matter what situation it's in, Hat provides shimmering, metallic timbres for any percussive purpose.

Notes: Loop is a high fidelity looper with four unique recording modes and an intuitive user interface. It can capture up to five minutes of audio with reverse, and half-speed playback accessible. Each recording can use one of four modes: Sound on Sound, Dub, Replace, and Infinite (i.e. Frippertronics). Whether you're looking for minimal part layering, or full blown ambient soundscapes, Loop will take your patch for a ride.

High fidelity audio - 24-bit, 48kHz with five minutes of recording time
Four recording modes: Sound on sound, Dub, Replace, and Frippertronics
Intuitive interface
Half speed and reverse playback

Tech Specs:
Width: 2HP
Depth: 42mm

Notes: Mix is a 4 channel mixer that is great for audio or control voltage signals. Up to four inputs can be combined to a single output each with its own level control.

Notes: MMF is an analogue, multimode filter with a 12dB per octave slope. Its sonic character swings all the way from classic low pass to squelchy acid lines. Simultaneous outputs of low pass, high pass, and band pass filter types are provided allowing for many variations of the input signal. Whether you're looking for smooth and creamy, or resonant and wild, MMF can go there.

Notes: Play is a high-fidelity sample player with a full feature set.

Up to 32 samples can be loaded at a time and dynamically switched between using the file knob and associated CV input. Playback modes include one-shot, looping, or gated playback; all with extremely low latency. Transform your samples by pitching them up two octaves or down three octaves, all with a pitch knob that can be free running or quantized to semitones. The pitch CV input tracks volt per octave across its entire range and allows for musical sequencing of samples. Play ships with a pre-loaded SD card packed with loops, drum hits, and field recordings to get you up and running immediately.

Notes: Pluck is a physical modelling synth voice. It uses the Karplus-Strong algorithm to create plucked string sounds. The dampening control sets the size of the string and allows for dramatic timbral shifts.

The decay control changes note length from percussive transients to infinite harp sounds. In addition, four voice polyphony provides complex layered tones; all from a single sound source.

Strum a new chord with Pluck.

Notes: Pluck is a physical modelling synth voice. It uses the Karplus-Strong algorithm to create plucked string sounds. The dampening control sets the size of the string and allows for dramatic timbral shifts.

The decay control changes note length from percussive transients to infinite harp sounds. In addition, four voice polyphony provides complex layered tones; all from a single sound source.

Strum a new chord with Pluck.

Notes: Sine is a harmonically pure VCO with two distinct outputs.

The primary output contains a perfect sine wave with a wide frequency range and pristine volt per octave tracking. The Sub output features two sine tones that can be blended together to achieve a mix of one octave below, or a fifth above the primary output's frequency.

In addition, both outputs have an internal wavefolder that adds harmonic content to the signal allowing for spectrally complex tones within a single module. Keep your tones pure (or not!) with Sine.

Notes: Get glitchy with it.

The 2hp Slice is a compact beat repeat/glitch engine built to add clickless stutters, digital glitches, and more to your patch. With an onboard Triplet button, seamlessly switch between straight beat repeats to offset triplets, perfect for those trap style fills you can't live without. With massive repeat range, and CV/Gate inputs for complex glitch sequencing, Slice is everything you need to get glitchy with it, all in 2HP.

Tech Specs

Width: 2HP
Depth: 45mm
Power Consumption: +12V=83mA, -12V=8mA, +5V=0mA

The 2hp Slice will be available in both Silver aluminium and Black PCB front panels.

The 2hp Slice ships with a 10-16 power cable and 2 Silver M3 mounting screws.

Notes: Tune is a multi-scale pitch quantizer. It features 11 scales ranging from chromatic to octatonic with everything in between. In addition, the bias control allows the user to transpose the melody to a different octave or starting note.

This functionality opens up every musical mode for each of its 11 scales and provides a performable control for transforming melodies on the fly.

Notes: The 2hp VCA is a dual, linear VCA. It uses the renowned 2164 SSM architecture, giving it extremely low distortion and high quality audio outputs. With a CV input attenuator, and DC-coupled inputs this is your new go-to module for voltage controlled amplification of audio or CV.

Notes: Verb is a lush stereo reverb with a full feature set and superior audio quality. A wide range of reverb times take your sound from small room to never-ending concert hall.

CV over mix allows dynamic movement between the dry and reverberated sound, and the dampening control lets you dial in the perfect timbre for the wet signal. Whether you need a traditional reverb for an FX send or an esoteric sound design tool, Verb can take you there. Get lost in space with Verb.

Review: "The Box" is a collection of the earliest and perhaps most cherished recordings by UK producer Dennis Huddleston, better known as 36. Written between 2005 and 2012, it compiles the albums Hypersona (2009), Hollow (2010) and Lithea (2012) into a 6LP boxset, alongside a bonus LP of exclusive and unreleased tracks titled Orphans. Originally written as a triptych, The Box showcases an incredibly eclectic, deeply emotional range of tracks, bridged together by that optimistic melancholy, which has since become the hallmark of the 36 sound.

Notes: The Listen IO is a simple module which gets signals in and out of a Eurorack system by converting to and from normal modular levels. The top section converts any external signal to modular levels by providing up to 30x gain (+30dB), allowing you to use table-top synthesizers, keyboards, phones/tablets, computers, toys, microphones, etc. in your patches. The bottom section does the opposite: modular signals are converted to normal line level signals. The bottom two jacks can be used as line outs or as headphone jacks, so you and a friend can listen in stereo at the same time.

Each section has two inputs and outputs for use with a stereo signal or two mono signals. An LED bar graph for each output shows the signal level and clipping.

Notes: The Mini PEG is a clock-synced envelope generator and LFO whose envelope times are set by the time between clock pulses or "pings". The Mini PEG is the latest version of the classic 4ms Pingable Envelope Generator.

Specs

Mini PEG
8HP Eurorack format module
0.95" (24mm) maximum depth (includes power cable)
16-pin Eurorack power header

Power consumption
+12V: 55mA
-12V: 30mA

Envelope Outputs
Maximum voltage range (ENV OUT): -9.4V to +9.4V
Maximum amplitude (ENV OUT): 9.5Vpp
Voltage range (5V OUT): 0V to +5V

Frequency range: +/-0.1dB DC to 1kHz, -1.0dB@2.5kHz, -2.0dB@4kHz
12-bit, 40kHz sample rate
Clock Range

Period range: 29.16 hours to 250us (4kHz)
CV Inputs (Div/Mult and Shape)

Voltage range: -5V to +5V
Gate Inputs (Ping, Trigger, Cycle)
Rising edge threshold: 2.5V

Notes: Nice dual-module gate/envelope generator which can run off any audio signal. Feed it drums, synths, samples or a mic input and and generate CV modulation signals.

Supplier's Notes:
The Percussion Interface (PI) and PI Expander are a pair of Eurorack modules that generate gates and envelopes from acoustic drums, samplers, drum machines, and virtually any audio source.

Converting microphone, instrument, line and modular signals into CV and clock/gate signals, the PI and PI Expander are suited for synchronizing sequencers or other modules to the rhythm of an audio track or live percussion. The modules can simultaneously be used as a pre-amp for microphones or line-level signals, while generating inverted envelopes useful for side-chaining. The PI module contains all the core functionality and can be used without the Expander to conserve space. The Expander requires the main PI modules and adds three gain stage options, a modular-level audio output jack, a 1/4" (6.35mm) input jack, and envelope attenuation capabilities. The two modules are only sold together, they are not available separately.

Electrical and Mechanical Specifications:
Module size (PI):
4 HP Eurorack formal module
0.98" (25mm) maximum depth with power cable
10-pin Eurorack power header

Module size (PI EXP):
4 HP Eurorack formal module
0.98" (25mm) maximum depth with power cable
8-pin cable connects to PI

Power consumption:
with PI Expander
+12V: 104mA
-12V: 65mA
without PI Expander
+12V: 69mA
-12V: 56mA

Audio Inputs:
1/8" [3.5mm] on PI main module, and 1/4" [6.35mm] on PI Expander
100k input impedance, AC-coupled

Audio Outputs:
Voltage range: -10.4V to +10.8V, DC-coupled
1k output impedance
Gain Characteristics
Gain range: < -100dB to +54dB (500x)
Clip light turns blue when signal (post-gain) exceeds 2.5Vpp
Gate is triggered when signal (post-gain) exceeds 6.3Vpp
Clip light flashes red when signal clips on Audio Out jack (exceeds +10.8V)
Gate Out Jack
1k output impedance
+8V gate/trigger signal
6ms - 0.5s pulse width
+ Env Out jack (jack on PI main module)
1k output impedance
+9V peak (sustain), -60mV resting (off)
15ms attack time
70ms - 6s exponential decay time (1% of peak voltage)
- Env Out Jack (jack on PI main module)
1k output impedance
+9V resting (off), -150mV peak (sustain)
15ms attack time
70ms - 6s exponential decay time (1% of peak voltage)
Env. Out jack (attenuated jack on PI Expander)
1k to 26k variable output impedance
+9V maximum
-60mV minimum
Inv. Out jack (attenuated jack on PI Expander)
1k to 26k variable output impedance
+9V maximum
-150mV minimum
Included with the PI+EXP:
8-to-16 pin power cable
8-to-8 pin cable for connecting to the Expander
M3 Knurlie screws (4)

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod20 is 20HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod20 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod26 is 26HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod26 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod32 is 32HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod32 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: The Pod40X is 40HP with 2.00" (51mm) of available module depth. The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod40 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: The ADE-50 provides 3 all-analogue voltage controlled amplifiers based on a modern operational transconductance amplifier design.

The VCA's are designed to provide a good balance between the performance and specification of modern 'on-chip' VCA's and the character and musicality of classic analogue designs.

The OTA core of each VCA is fully discrete - it is built from only resistors, capacitors and transistors - however, the CV conditioning, audio input and output stages are built using high-quality op-amps giving the best balance between musicality, character and performance.

The ADE-50 provides a good signal-to-noise ratio, linearity, attenuation, an output level at unity gain at 5V CV input, minimal CV 'bleed' and minimal output offset/bias.

Notes: Junction requires a +12V / -12v power supply with a 2x5 pin ribbon cable (included). The red line of the ribbon cable must be aligned with the -12V marking next to the module's power header and on your case's power distribution board. Junction draws 23mA from the +12 rail and 20mA from the -12 rail. Please ensure you have
enough power available before installing.

About Junction

Junction is a compact, 4 channel attenuverter, cascading mixer and multiple designed to fine tune the control voltages in your rack to the perfect range for their destinations. Junction can be used as a source of fixed voltage, offset another voltage, or mix multiple voltages together to create complex and dynamic modulation.

Features

Each channel on Junction has a knob (1) that acts as a manual control for the attenuverter. Center position (12 o clock) is 0V. The first channel input (2) is normalized to +5V when no cable is plugged into it.

A buffered copy of the input signal of the first channel is present on all of the other inputs from from the first (2) to the last (8). This duplication is "cascading" as shown by the arrow graphics on the panel - if a cable is patched into any input, it "breaks" the cascading multiple - all unpatched inputs carry the signal present at the uppermost patched input (or +5V if no inputs are patched). For example, if a signal is patched into the second channel's input (4) the third (6) and fourth (8) channel inputs would carry a copy of the second channel's input instead of the first channel input.

Junction's channels are mixed on the outputs. The output mixer is also "cascading" - when a cable is patched into an output, it carries a mix of it's own output and all unpatched channel outputs above it. For example, if only the last channel output (9) is patched, this output will carry a mix of all of the outputs. Patching the first channel output (3) would remove it from this mix.

Even though Junction's inputs cascade and outputs mix, Junction's output will clip at the Eurorack power rail voltages of +12 and -12V. It is not possible to output a voltage outside of this range, regardless of the signals patched into Junction.

23mA +12 / 20mA -12 4 HP / 25mm
Deep Reverse Power Protection

Notes: This small utility is the pedal's lover best friend, it allows 2 diferent chains of pedals to be independently connected to your synth.

The Send channels attenuate the synth level to instrument level.

The Return channels amplify the signal from instrument to synth level.

Specs:
- Width: 4 HP
- Depth: 3 cm
- Max current: 10mA

Notes: This new module should not be judged by it's size, at 6hp it's packed with features.

At its core it features a noise source and two precision Sample & Holds with 0.01% of maximum deviation from the Input which allows for quantized signals to be sent through without any noticeable detuning or the typical voltage drops over time.

The Sample & Hold sections can also be used as a Track & Hold meaning it holds the incoming input while the Trigger input is ON and lets the input flow to the output when the Trigger input is OFF.
Each section also features it's own slew processor with a single control over attack and decay and an ON/OFF switch.

The noise signal is normalled to both sections inputs, meaning that without a jack plugged into the Input the sample and hold function will act upon the incoming noise signal generating random CV values.

The [Trigger A Alternate] switch allows to Link both sections so that any trigger input in Trigger A will alternate between triggering the A and B section.

Besides each section outputs there's also 4 extra outputs: Noise, Difference, Average and Sum. The Noise output is coming from the noise source, the Difference output is the subtraction of section A minus section B, the Average output is the sum of both A plus B and then divided by 2 and finally the Sum output is the sum of both A plus B sections.

MECHANICAL:
Format: Eurorack
Width: 6 HP
Depth: 4 cm

ELECTRICAL:
Max current: +50mA/-50mA
Bus Board Cable: 8 × 2 IDC (Doepfer style) connector

Notes: Inspired and officially licensed from Teia's Stochastic Function Generator which was introduced in 2013 but is no longer available. This earlier version served as an inspiration, but with a completely rebuilt and reprogrammed mcu to a fully featured 4 voice 2 stage envelope and slew generator.

ADDAC System ADDAC506B VC Stochastic Function Generator Expansion Module (black faceplateADDAC System ADDAC506B VC Stochastic Function Generator Expansion Module (black faceplate
This expansion allows extra I/O to the ADDAC506, namelly:

Four trigger inputs for the random engine.

Four CV random outputs from the random engine.

Notes: ADDAC710 is a dual channel Isolated DI box and is all about keeping the sound coming from your Modular free from any undesired noisy interferences, making sure that what you're getting from your outputs is what your Modular is actually producing. It provides galvanic electrical isolation between the Modular system and external sources preventing impedance mismatch and ground loop induced hum. ADDAC's 710 circuit is designed around a unity 1:1 type Low-cost Audio Transformer operating in the 20 Hz to 20 KHz range, this impedance matching transformer provides two fully balanced outputs (via XLR connectors). ADDAC710 is a low-cost alternative to the ADDAC800X High-End Outputs module, we redesigned the original circuit using a smaller low-cost transformer that also reduced its depth allowing it to fit shallow Eurorack cases.

There are two independent channels on the module with:

Audio Input

LIFT/FLOAT/GND toggle switch
Signal overload warning led
XLR Output

The LIFT/FLOAT/GND 3-way switch lets you choose between lift, ground or floating ground.
In the LIFT position (left) the module circuit will be "lifted" to ground through a 100R resistor and a 10nF capacitor.
In the FLOAT position (middle) Ground will not be shared leaving ins and outs grounds completely apart from each other fully isolating both signals. in the GND position (right) Ground will be shared between inputs and outputs, here no isolation is used.
Any of these three positions may be the best form of avoiding ground loops or any other undesired interference occurring between your modular and the sound system you're plugging it into. Try out which one of these options will work best in any given situation.

Tech Specs:

6HP
4 cm deep
40mA +12V
40mA -12V

The importance of using Audio Transformers
Applying a transformer balanced output isolation has lots of advantages over other less expensive ways for dealing with ground loop issues. This method provides the chance to set a very simple and clean circuit in which the signal transfer process develops smoothly and humming free. The transformer is a device that performs both signal balancing and high-to-low (or vice-versa) impedance conversion, while rejecting straggled DC voltage and Radio Frequency Interference from signal passing through a magnetic bridge. In a transformer, two (or more) coils (called windings) of insulated wire wound around a magnetic metal core allow for its input(s) and output(s) not to be physically connected together. When an AC signal passes through the input winding (the primary), a perfectly related AC signal appears on the output winding (the secondary). This way, by the fact that signal flows via inductive coupling between the two windings of the transformer, this module presents a most accurate electrical isolation between its input and output. A same number of windings on each coil guarantees that there's no gain loss when audio signal passes from the primary to the secondary windings. Furthermore, since these two windings are insulated from each other, the transformer will electrically isolate ADDAC710 from any other device, preventing hum problems coming from an outsider ground. Being a low-cost transformer the frequency response curve is not as linear as our 800X, still the -0.2dB attenuation at 50Hz feels negligible.

Phantom Power

+48V Phantom Power is NOT needed for the module to operate.
In any case having Phantom Power ON won't influence the module operation.

Notes: ADDAC809 is a dynamic CV operated I/O router that allows one source (Audio or CV) to be routed through 2 different chains (of one or more modules) before being sent to an output.
Six routing patterns are allowed:

1. IN > OUT
2. IN > CHAIN A > OUT
3. IN > CHAIN B > OUT
4. IN > CHAIN A > CHAIN B > OUT
5. IN > CHAIN B > CHAIN A > OUT
6. IN > > OUT
A practical example is to have an audio source, a delay and a looper.
And the question: should the delay be placed before or after the looper? Sometimes you may need the delay to be before the looper as you may want to sample the audio with the delay or sample the pure audio source and apply the delay afterwards.
This small utility module solves this issue on the fly without having to repatch anything.

INPUTS & OUTPUTS

TO CHAIN B: Connect to your Chain B input
FROM CHAIN B: Connect to your Chain B output
TO CHAIN A: Connect to your Chain A input
FROM CHAIN A: Connect to your Chain A output
INPUT: Connect to your Input Source
OUTPUT: Connect to your Output Source

ROUTING PATTERNS

There are 2 ways to address the six routing patterns:

Buttons: using the frontpanel push buttons and/or dedicated trigger inputs to latch between 2 states.
BYPASS: Chooses between Pattern 1 and any other pattern
PARALLEL: Chooses between Pattern 6 and any other pattern
ORDER: Chooses the order A before B or B before A
DUAL/SINGLE: Chooses to use a Dual (A>B or B>A) or Single chain (A or B)
CV: The dedicated CV input expects a 0 to +5v input and allows to jump to the precise routing pattern using a specific voltage interval in increments of approx. 0.83V:

Pattern 1: 0v to 0.83v
Pattern 2: 0.83v to 1.66v
Pattern 3: 1.66v to 2.5v
Pattern 4: 2.5v to 3.33V
Pattern 5: 3.33v to 4.16V
Pattern 6: 4.16v to 5V

Tech Specs:

Width: 12 HP
Depth: 55mm
Current: 80mA +12V / 30mA -12V

Review: ***B-STOCK: Sleeve damaged but otherwise in excellent condition***


Made and released way back in 1958, Somethin' Else is a classic jazz album by the American alto saxophonist Cannonball Adderley, notably his only ever album for the esteemed Blue Note label. It famously hears Adderley enlist the help of trumpeter Miles Davis as one of its sidemen, and this was an ongoing relationship that later paved the way for popular jazz as a whole; without Somethin' Else, we wouldn't have Kind Of Blue, for which Adderley would contribute his sax playing just a year later. Though it is a testament to the unity of two great core musicians, we also hear the piano stylings of Hank Jones, bassist Sam Jones and drummer Art Blakey.

Notes: DVCA

DVCA is a dual VCA based on the Mutable Instruments Veils. It features two separate voltage-controlled amplifiers, both with a gain and a response curve potentiometer, that is variable from linear to exponential. The outputs are normalized, so when no patch cable is present on output 1, output 2 will contain both signals, allowing the module to be used as a mixer. Several DVCAs can be daisy-chained for voltage-controlled mixer operation. It comes with jack lights that can be disabled via a jumper on the back.

These modules use tall bushing potentiometers to offer a more stable feel.

The module is fully assembled and tested. Eurorack power cable included.

Notes: SHTH - Sample and Hold - Track and Hold

Create stepped outputs using two different classic synthesis techniques, sample & hold and/or track & hold.

Sample & Hold

The top four jacks make up the sample and hold section. There is a noise output that is normalled to the input so you can pass a gate/trig signal into the SAMP input to get a stepped output at the OUT jack.

IN - Signal that will be sampled, normalled to NSE output
SAMP - When high updates the voltage being sent to the output
NSE - White noise output
OUT - The sampled output (freezes the value from the IN jack when the SAMP jack receives a high signal)
Track & Hold

The bottom four jacks make up the track and hold section. There is a walk signal (a randomish meandering voltage) that is normalled to the input. Track and hold is the opposite of sample and hold in that it will pass the IN value to the OUT jack until the TRACK input receives a high gate. While the TRACK input is high it will hold the value. After the TRACK input goes low, it will begin tracking the IN signal again.

IN - Signal that will be tracked
TRACK - When high the value will be held at the output
WALK - A meandering voltage
OUT - The track output (follows IN while TRACK is low, held voltage while TRACK is high)
CC-BY-SA Emelie Gillett

Notes: Headband with three connection modes: W+ Link for wireless ultra-low latency and lossless audio, Bluetoothr 5.0, and cabled. Built-in microphone, includes USB-C charging cable.

Notes: More affordable XE version of AIAIAI's modular TMA-2 headphones. Bluetooth enabled for wireless use, with lightweight headband design and the brand's signature bio-diaphragm drivers.

Supplier's Notes:

Signature AIAIAI bio-diaphragm speaker tuned for clarity and detail.

Critically acclaimed sound stage specifically designed for music creation with a clear and highly detailed sound representation.

Lightweight design and REPREVEr cushions.

Ultra soft on-ear cushions made from recycled materials (including plastic bottles) and lightweight design to prevent excessive warmth and ensure optimal comfort for longer listening sessions.

Bluetooth 5.0 connectivity with +40h playback time.

High quality wireless audio, +40h playback time on any Bluetooth enabled device.

Intuitive multi-functional joystick controls.

Complete control of music and calls with multi-directional joystick, and dual mics for improved voice quality and clarity.

Modular product design.

This TMA-2 modular headphone system offers a customizable solution that adapts to your creative process. With interchangeable components such as earpads, cables, and drivers, you can upgrade or change parts of your headphones to improve sound quality, comfort, or style.

Headphones for life.

AIAIAI offer lifetime trade-in for your headphones or modular parts. With this program, users can leverage the modular product design to get maximum value from their purchase by swapping out used or non-functional headphones or parts for future credit. This means only investing in one pair of headphones, for life.

Signature AIAIAI bio-diaphragm speaker tuned for clarity and detail.
Lightweight design and REPREVEr cushions.
Bluetooth 5.0 connectivity with +40h playback time.
Intuitive multi-functional joystick controls.
Responsible modular headphones - Headphones for life.


SPECIFICATIONS AND PARTS

S10 . Bluetooth 5.0 - Detailed sound - Bio-diaphragm
Bluetoothr speaker units with a diaphragm made from stiff bio-cellulose for more defined high-frequency details, more pronounced mid-range, better dynamics, and more natural tonality. Delivered as a pair, including USB-C charging cable

H01 . Slim - PU foam
Slim and light-weight polycarbonate headband with soft, durable PU foam padding.

E10 . On ear - REPREVE
On-ear cushions made from memory foam and covered with REPREVEr, an ultra soft hi-tech fiber preventing excessive warmth and ensuring optimal comfort for longer listening sessions. Partly made from recycled plastic bottles. Delivered as a pair.

C05 . Straight - 1.2m
Straight 1.2m thermo plastic cable. Soft touch surface and perfect for small workstations.

A01 . Protective pouch
Designed to protect your headphones from dust and scratches, the A01 protective pouch is made from soft nylon and features a mesh inside. Fits any TMA-2 and Tracks headphone.

Notes: AIAIAI's affordable XE range might just offer the best value studio headphones around. Balance S01 drivers and comfortable E04 ear pads are paired with a slim headband for great sound at a reasonable price.

Supplier's Notes:
Modular studio headphones.

Balanced and detailed sound
Enhanced comfort over-ear cushions
High sound isolation
Weighing only 190g
Modular headphone design

Modular studio headphones with highly detailed sound and full bass extension, balanced for music production. Comfortable PU leather over-ear earpads provide high isolation, reducing surrounding noise when creating on the go. Weighing only 190g for enhanced comfort over extended periods of time.

Balanced detailed sound

Critically acclaimed sound stage specifically designed for studio use with a clear and highly detailed sound representation.

The speaker unit contains a bio-cellulose diaphragm made from bacterial cellulose, an organic compound grown using certain types of bacteria. The precision-grown diaphragm from bio-cellulose is stiffer, lighter, and stronger than regular PET speaker units, allowing the sound-producing diaphragm to vibrate without the levels of distortion found in other speakers.

Each of these qualities results in more accurate and detailed sound from the speaker with the ability to retain clarity of sound at high volumes.

With a minimal and lightweight construction of only 190g, the TMA-2 Studio XE is ideal for the flexible, versatile and dynamic workflow of modern music makers.

Lightweight & comfortable

High grade over-ear memory foam cushions covered in resilient and soft PU leather, for enhanced comfort during long creation sessions or live performances. The over-ear cushion design provides high sound isolation when creating in noisy environments.

Headband made from high grade nylon combined with durable PU leather earpads, results in a total headphone weight of only 190g.

In the box

S01 . Balanced sound - Bio-diaphragm

Engineered with a 40mm speaker diaphragm made from stiff bio-cellulose to reduce distortion and increase transparency. Tuned for a balanced, accurate sound. Balanced sound - Bio-diaphragm.

H01 . Slim - PU foam

Slim and lightweight polycarbonate headband with soft, durable PU foam padding.

E04 . Over ear - PU leather

Soft over-ear memory foam cushions covered with PU leather. The thickness and materials provide better comfort and excellent isolation. Adding a low end boost for a warmer sound with powerful dynamics.

C05 . Straight - 1.5m - Adapter

Straight black 1.5m thermo plastic cable with soft touch surface. Comes with 1/4 to 1/8 screw-on adapter.

Headphones for life

As a music creator, you need headphones that can keep up with your evolving needs and styles. These TMA-2 modular headphone system offers a customizable solution that adapts to your creative process. With interchangeable components such as earpads, cables, and drivers, you can upgrade or change parts of your headphones to improve sound quality, comfort, or style.

By investing in this modular headphone system, you're not just buying headphones - you're investing in a long-term solution that evolves with your music. This reduces electronic waste while ensuring that you always have the optimal headphones just for you.

Diaphragm: Bio-cellulose
Driver diameter: 40 mm
Impedance: 32 Ohm
Magnet: High-grade Neodymium
Max power: 100 mW
Rated power: 40 mW
Resonance freq: 80 Hz

Notes: Wireless music creation with ultra-low latency and uncompressed audio with W+ Link technology.

Uncompressed and robust 16ms latency connection for high quality wireless audio designed for enhanced freedom and creativity.

Signature AIAIAI bio-diaphragm speaker tuned for clarity and detail.

Critically acclaimed sound stage specifically designed for music creation with a clear and highly detailed sound representation.

Enhanced comfort with Alcantarar over-ear memory foam cushions.

Soft over-ear memory foam cushions covered with resilient, CO2 neutral, and highly comfortable Alcantarar, ideal for longer sessions.

Modular product design.

This TMA-2 modular headphone system offers a customizable solution that adapts to your creative process. With interchangeable components such as earpads, cables, and drivers, you can upgrade or change parts of your headphones to improve sound quality, comfort, or style.

Extended versatility with added Bluetooth for +80h playback and hi-fi coiled cable.

Seamlessly switch to Bluetooth 5.0 with +80h playback for everyday listening and inspiration, and a coiled hi-fi cable included for a traditional connection.

Headphones for life.

AIAIAI offer lifetime trade-in for your headphones or modular parts. With this program, users can leverage the modular product design to get maximum value from their purchase by swapping out used or non-functional headphones or parts for future credit. This means only investing in one pair of headphones, for life.

Wireless music creation with ultra-low latency and uncompressed audio with W+ Link technology.
Signature AIAIAI bio-diaphragm speaker tuned for clarity and detail.
Enhanced comfort with Alcantarar over-ear memory foam cushions.
Modular product design - Headphones for life.
Extended versatility with added Bluetooth for +80h playback and hi-fi coiled cable.

Technical specifications

W+ Link Headband

Audio quality: Lossless
Latency: 16 ms
Operating range: 12 m
Playback time: 16 hrs
Bluetooth version: 5.0
Bluetooth range: 10 m
Charging time: 2 hrs
Battery: 970 mAh
Omnidirectional mic: 100 Hz - 10 kHz
Bluetooth codecs: AAC, SBC

W+ Link Transmitter

Audio quality: Lossless
Latency: 16 ms
Operating range: 12 m
Playback time: 30 hrs
Charging time: 3 hrs
Battery 2700 mAh

Notes: The Low Fat is a new 2hp Eurorack module by AJH Synth, it's a High Pass filter, with frequency control by either manual pot, and/or external CV with attenuator. It's intended to compliment other filters, particularly low pass VCF modules, in practical tasks such as removing excessive low frequencies, for example when the bass is swamping a mix. It can be switched between 6dB (1 pole) response and 12dB (2 pole) response.

By patching a CV signal to the FCV input it can be voltage-controlled and used musically as with any other VCF. When used in conjunction with a LP filter it forms a fully customisable band pass filter, allowing the range of passbands to be cherry-picked. Feeding in a 1V/Oct pitch CV and setting the FCV pot to a suitable level allows it to track an incoming pitch CV, so the amount of High Pass filtering remains constant as the pitch of the incoming VCOs traverse up and down the frequency range. This can be particularly useful in creating percussive sounds, such as snares and hats, but also on sequenced bass lines. Since it is only 2HP it's a great way to occupy one of those frustrating gaps in your eurorack modular case with something that is deceptively useful, and adds another dimension to the classic bass monster that is the Transistor Ladder Filter.

Dimensions:
2 HP
26 mm deep

Current Draw:
9 mA +12V
12 mA -12V
0 mA 5V

Notes: This is a precision active buffer and multiple. This module has outstanding performance: it features very high input impedance, very low output impedance and an offset voltage of <1mV.

Not all active multi's are born equal, some designs do not fully solve impedance mismatch and tracking problems, or they apply offset voltages to the output and in rare cases can cause more problems than they solve!

AJH Synth have added a very useful (and unique) feature to cure tracking problems: four of the five outputs can be adjusted up or down by +/-5% from the front panel, so that VCO's and VCF's that don't track 1V/Oct exactly can be easily compensated to track correctly without having to re-calibrate the VCO or VCF themselves.

Notes: Great value for FL Studio users with this dedicated controller which channels Akai's expertise in order to offer a hands-on experience for your DAW. Quicker workflow and easier access to settings.

Supplier's Notes:
The new Akai Professional Fire represents the first of its kind, a dedicated hardware controller for the FL Studio Digital Audio Workstation (DAW) platform. Created in close partnership with Image-Line, Fire is a high-performance tool designed to enhance the workflow and music-creating experience for all FL Studio producers.

Fire features a dedicated browser function to navigate, audition and load your audio samples, recall project files and open plugins. Simply select browser and use the Select rotary encoder to preview and load content and devices within FL Studio - The graphical OLED display makes for easy browsing and controlling the various files, menus and parameters within your session a breeze.

Featuring plug-and-play integration, within seconds you'll be creating patterns and building tracks using Fire's 4 x 16 velocity-sensitive RGB pad matrix, designed for immediate interaction with FL Studio's celebrated step sequencer.

Get hands-on with your production with everything you need to control FL Studio's channels and patterns. With direct hardware control over your session, you can easily mute and solo channels, expand the grid matrix, select new channels, navigate through patterns and much more without touching a mouse.

From searing synth leads to lush pads, Fire's Note mode provides the ultimate platform to add melody and harmony to your production. Simply push the Note button and Fire's RGB pads switch-up to a MIDI keyboard giving you three octaves of note data, perfect for playing all of your instruments hosted in FL Studio.

Fire's pad matrix features an MPC-style 16-pad layout for seamless integration with FPC and SliceX. This is great for FL Studio producers who want a traditional beat-making experience or want to use their finger-drumming chops on the track.

Whether you're a studio producer refining an arrangement or live performer looking to take your sessions to the stage, Fire's Performance mode provides the ideal platform to remix and reimagine your tracks. Simply select Performance mode and launch MIDI clips and audio directly from Fire's RGB pad matrix for a truly inspiring live production experience.

Fire also provides immediate access to transport controls straight from the hardware. Record, Stop, Play, as well as a button to instantly switch between Pattern and Song mode are intuitively placed for mouse-free control of FL Studio. Plus, these all double up with secondary controls providing access to Loop Record, Countdown, Wait and Metronome.

Bringing a tactile, mouse-free mixing solution to the FL Studio environment, Fire includes 4 banks of 4 touch-capacitive knobs that enable the user to instantly see and adjust parameter values. Providing control over channel, mixer and user-assignable parameters, this enables a more intuitive and enjoyable workflow. From tweaking volume and pan within FL Studio's mixer to adjusting filter controls within the selected channel and recording automation, you'll spend less time clicking and more time executing.

Speed is power. Up to four Fire devices can be connected at once, enabling unprecedented hardware control over the FL Studio mixing and production workflow. Expand channels or make more in the sequencer accessible by selecting Multi-Device Mode from the OLED display. Instantly expand the 4 x16 matrix of one Fire unit to an 8 x 32 workflow.

Enter the ground-breaking, high-powered workflow heard all over the charts with the FL Studio Fruity Fire Edition software, included with Fire. FL Studio is a complete software music production environment, the culmination of more than 20 years of innovative development. The software features everything you need in one package to compose, arrange, edit, mix and master professional quality music. With access to FL Studio's piano roll editor, step sequencer, playlist, VST instrument support, full automation functionality, plus 18+ virtual instruments and over a dozen built-in effects and processors, FL Studio Fruity Fire Edition provides the ultimate platform to spark that initial idea, ignite your creativity and complete your masterpiece - all in an ultra-intuitive, inspiring environment engineered to keep you tuned in to what's important, your music.

Pads: (64) Velocity-Sensitive RGB Backlit Pads

Knobs:
4 x 360 degree Assignable Touch-Capacitive Knobs
1 x 360 Encoder for Display Navigation

Buttons: 20 x Dedicated function buttons; Red, Amber or Green backlit
Display: OLED Display
Connections: 1 USB Type-B Port

SYSTEM REQUIREMENTS
Windows 7, 8, 10 or later
4GB of RAM or higher recommended
4GB free disk space
FL Studio 20.0.5 or later

Mac OS:
10.11 or later
4GB of RAM or higher recommended
4GB free disk space
FL Studio 20.0.5 or later

Notes: The new Akai Professional Fire represents the first of its kind, a dedicated hardware controller for the FL Studio Digital Audio Workstation (DAW) platform. Created in close partnership with Image-Line, Fire is a high-performance tool designed to enhance the workflow and music-creating experience for all FL Studio producers.

Fire features a dedicated browser function to navigate, audition and load your audio samples, recall project files and open plugins. Simply select browser and use the Select rotary encoder to preview and load content and devices within FL Studio - The graphical OLED display makes for easy browsing and controlling the various files, menus and parameters within your session a breeze.

Featuring plug-and-play integration, within seconds you'll be creating patterns and building tracks using Fire's 4 x 16 velocity-sensitive RGB pad matrix, designed for immediate interaction with FL Studio's celebrated step sequencer. Get hands-on with your production with everything you need to control FL Studio's channels and patterns. With direct hardware control over your session, you can easily mute and solo channels, expand the grid matrix, select new channels, navigate through patterns and much more without touching a mouse.

Get hands-on with your production with everything you need to control FL Studio's channels and patterns. With direct hardware control over your session, you can easily mute and solo channels, expand the grid matrix, select new channels, navigate through patterns and much more without touching a mouse.

From searing synth leads to lush pads, Fire's Note mode provides the ultimate platform to add melody and harmony to your production. Simply push the Note button and Fire's RGB pads switch-up to a MIDI keyboard giving you three octaves of note data, perfect for playing all of your instruments hosted in FL Studio.

Fire's pad matrix features an MPC-style 16-pad layout for seamless integration with FPC and SliceX. This is great for FL Studio producers who want a traditional beat-making experience or want to use their finger-drumming chops on the track.

Whether you're a studio producer refining an arrangement or live performer looking to take your sessions to the stage, Fire's Performance mode provides the ideal platform to remix and reimagine your tracks. Simply select Performance mode and launch MIDI clips and audio directly from Fire's RGB pad matrix for a truly inspiring live production experience.

Fire also provides immediate access to transport controls straight from the hardware. Record, Stop, Play, as well as a button to instantly switch between Pattern and Song mode are intuitively placed for mouse-free control of FL Studio. Plus, these all double up with secondary controls providing access to Loop Record, Countdown, Wait and Metronome.

Bringing a tactile, mouse-free mixing solution to the FL Studio environment, Fire includes 4 banks of 4 touch-capacitive knobs that enable the user to instantly see and adjust parameter values. Providing control over channel, mixer and user-assignable parameters, this enables a more intuitive and enjoyable workflow. From tweaking volume and pan within FL Studio's mixer to adjusting filter controls within the selected channel and recording automation, you'll spend less time clicking and more time executing.

Speed is power. Up to four Fire devices can be connected at once, enabling unprecedented hardware control over the FL Studio mixing and production workflow. Expand channels or make more in the sequencer accessible by selecting Multi-Device Mode from the OLED display. Instantly expand the 4 x16 matrix of one Fire unit to an 8 x 32 workflow.

Pads: (64) Velocity-Sensitive RGB Backlit Pads

Knobs:
4 x 360 degree Assignable Touch-Capacitive Knobs
1 x 360 Encoder for Display Navigation

Buttons: 20 x Dedicated function buttons; Red, Amber or Green backlit
Display: OLED Display
Connections: 1 USB Type-B Port

SYSTEM REQUIREMENTS
Windows:
Windows 7, 8, 10 or later
4GB of RAM or higher recommended
4GB free disk space
FL Studio 20.0.5 or later

Mac OS:
10.11 or later
4GB of RAM or higher recommended
4GB free disk space
FL Studio 20.0.5 or later

Notes: The ultra-portable MPK Mini Play is based on the world's most popular midi controller - Akai Professional's MPK Mini-but now it comes packed with 128 sounds and its own built-in speaker. With 8 backlit MPC drum pads and a 4-way joystick for simple control, players have all they need to play their music anytime, anywhere. Four knobs (two banks capable of controlling eight different parameters) can be used to tweak sounds and edit multiple parameters in real-time, giving musicians even more performance possibilities. Powered by 3 "AA" batteries, the MPK Mini Play is built for hours of wireless fun.

Not just a mini keyboard, the MPK Mini Play can also connect to a computer via USB port for the same plug-and-play MIDI functionality as the classic MPK Mini controllers. If not disturbing others is a priority, players can use the mini-audio output jack to connect headphones to the MPK Mini Play. When you want a bigger sound, simply connect to external speakers using the same output jack. All-in-one, easy-to-use fun with "pro" features - that's the MPK Mini Play!

"We are extremely excited to introduce the MPK Mini Play," said Dan Gill, Product Manager for Akai Professional. "The MPK Mini was a huge hit with musicians and now having all those sounds on-board with a built-in speaker, along with its go-anywhere portability, Play opens up new musical possibilities that people are going to love."

KEY SPECS

Keys
25 velocity-sensitive

Pads
8 pressure and velocity sensitive
MPC-style Light-up Pads x 2 Banks

Knobs
4 assignable controller pots
1 x 360 Encoder for Display Navigation
1 Volume control

Computer Interface
USB-MIDI communications to Mac/PC

Octaves
10 with Octave Up and Down

Arpeggiator
Yes

Additional Controls
Pitchbend/Mod Joystick
Note Repeat Button
Full Level Button
Tap Tempo Button

Additional Inputs
1 14" (6.35mm) TS input for sustain pedal

Output
1 1/8" (3.5mm) headphone output
Built-in speaker

Power
USB bus powered
3 x AA batteries

Dimensions:
12.29" x 6.80" x 1.83" / 31.2 x 17.2 x 4.6 cm (WxDxH)
1.6 lbs

Notes: Third-generation version of Akai's compact keyboard is a portable instrument in its own right. Battery operation and built-in sounds and speaker let you make music anywhere. Keys and MPC pads offer full control.

Supplier's Notes:
Play Music Anywhere

Musical inspiration can happen anywhere and MPK mini Play mk3 is the perfect portable companion to capture those melodies and harmonies, anytime and anywhere. With battery-operated performance at 14+ hours, MPK mini Play mk3 users don't have to worry about power adapters, chargers, or cables when it's time to play music. The upgraded built-in speaker delivers increased output and added low-end response, making for more enjoyable playing and jamming. With an improved listening experience, users can dive into the 128+ onboard instruments and drum kits including acoustic and electric pianos, synth leads and pads, and more. MPK mini Play mk3 also houses a 1/8-inch headphone output jack for quiet practicing or songwriting without disturbing others.

Professional Performance

At the heart of the MPK mini Play mk3 is the new Gen 2 keybed. This new keybed delivers dynamic performances and accurate velocity response with a feel that players will certainly appreciate. While it maintains its sleek, compact footprint, MPK mini Play mk3 is more playable and comfortable than ever and ready for hours of playing. The 8 pads have been upgraded to real, velocity-sensitive MPC drum pads, offering optimal feel and response for even the most percussive drum parts. With Class Compliant, plug-and-play capability, MPK mini Play mk3 doubles as a powerful MIDI controller and instantly connects to your favourite DAW for immediate music production duties. 4 assignable rotary encoder knobs offer versatile control of MIDI parameters like pan or automation for super-precise editing. With its sturdy construction and build, MPK mini Play mk3 is ready to travel securely alongside any favourite music production items in backpacks or bags.

Limitless Creativity with MPC Beats Software DAW - Effects and Instruments Included

The MPK mini Play mk3 comes bundled with MPC Beats, the powerful music-making and recording desktop software DAW for Mac and PC, based on the iconic MPC hardware. This DAW features a full array of musical instrument plugins, effect plugins, and audio and drum samples ready for your next hit production. In addition to MPC Beats, MPK mini Play mk3 also includes multiple world-class plugin instruments from award-winning sound design company AIR Music Technology. Available in both AU and VST are Hybrid 3 - a powerful polyphonic analogue synth, Mini Grand - an acoustic piano instrument, and Velvet - a vintage electric piano instrument.

Educational Software Included

MPK mini Play mk3 comes with a Melodics educational package. Available as both a desktop and iPad app, Melodics features instruction for MIDI keyboards, pad controllers, and e-drums, offering tailored cross-genre lessons and realtime feedback designed to help refine necessary music creation skills. The free Melodics download includes 60 lessons to get started and with plug and play support, no extensive set-up is required. Sign-up for Melodics with your new MPK mini Play mk3 and discover fun, engaging music performance training and education.

Technical Specifications

Power: Via USB or 4 AA alkaline batteries
Dimensions (diameter x length):12.5" x 7.0" x 2.3" / 317 x 178 x 58 mm
Weight 1.9 lbs./0.86 kg