Search dance music

Notes: Poti II expander notable features:

- per-channel input and output attenuation for the SINE and ASSGN outputs
- per-channel shape modulation with switchable destination (wave folding, shape switching, PWM)
- stores settings during a power cycle
- LED indication of the discrepancy between the stored setting and current pot position
- 4HP
- +10/-0mA from Batumi II

Notes: Part of Xaoc's Leibniz Binary Subsystem, the updated Drezno ADC/DAC module builds on the original with higher resolution converters, allowing you to use it for pitch quantisation.

Supplier's Notes:
Drezno II is an improved version of the original Drezno module. It is an essential member of the 8-bit Xaoc Devices Leibniz Binary Subsystem. The Leibniz subsystem is a family of modules that operate on 8 binary (two-state, on/off) signals. These signals are arranged as 8 bits of digital data and may represent analogue signals and voltages, or they may be whatever you want them to be (clocks, gates, rhythms, etc.).

Drezno features an ADC (analogue-to-digital-converter) and DAC (digital-to-analogue-converter), allowing it to act as an analog front-end of the system. In other words, Drezno allows one to convert analogue signals and CVs into digital numbers, as well as to obtain analogue signals back from some other digital numbers (or 8 binary signals). Between these two conversions there is a whole universe of digital shenanigans waiting to happen resulting in all kinds of signal transformations and modulations.

Both (ADC and DAC) sections of Drezno can work independently, or they can be linked. Input and output range of analogue signals may be adjusted using Gain and Offset sliders. Individual bit outputs (for the ADC) and inputs (DAC) allow for extensive cross-patching and the creation of complex waveforms and rhythms. A very fast clock (up to 2MHz) at which the conversions are performed may be replaced with any external clock (for each section separately).

Compared to its predecessor, Drezno II uses new converters of much higher resolution which results in much lower noise floor and higher accuracy. The lower bits are much more stable than before. It is easy now to use Drezno for quantizing pitch voltages with accurate results with 128 or 256 semitone steps. Potentiometer ranges are factory calibrated for precise chromatic scale. A new switch on the front panel allows the user to select the calibrated range of 10Vpp or 20Vpp, so that the lowest bit or the second bit correspond to 1 semitone.

Technical details

Eurorack synth compatible
12hp, skiff friendly
Current draw: +80mA/-50mA
Reverse power protection

Notes: Another update for WMD's clever dual VCA, this time a little bigger to give more control. Digital control of CV and attenuation gives lots of creative options. Third time's a charm.

Supplier's Notes:
WMD have done several designs of this circuit over the years, the first one had no knobs, the second was too small, the MKIII is finally how this circuit should be packaged. This module does some really cool stuff and is super useful in any system.

The Digital VCA lets signal through like a normal VCA, but the CV and attenuation level is controlled digitally. This lets us do things like wait until there is a zero crossing to change the amplitude, resulting in clickless amplitude changes.

The Trigger mode causes the VCA to only update when a trigger is received. The addition of a noise circuit for each side let us do a very quick and easy sample and hold that never droops. With no input, 5V is normaled to the attenuator, so you get a 0-5V sample and hold. In Bipolar mode, you can get -5 to +5V.

Both sides have bipolar VCA mode (polarizer), which lets them invert the signal when negative CV comes in. Also known as ring modulation. With the zero crossing detector, this can produce some super wild wave shapes.

Features

Dual VCA Design
Unipolar or Bipolar Operation
DC Coupled Analogue Signal Path
Low Distortion / Low Noise
VCA Closes Completely
Zero Crossing Detector Mode
Trigger Mode
Two Independent Noise Sources
8 bit CV resolution
Great for Fast Envelopes and Sine Bass Sounds

Specifications

Power: +65mA, -45mA
Width: 8HP
Depth: 35mm with cables
Height: Eurorack 3U (128.5mm)
Board Height Behind Panel: 112mm
CV/Signal Input Impedance: 100k
Output Impedance: 1k
UPD in 3.3V Threshold Schmitt Trigger
ZCD produces 15us 5V pulse
5V CV to fully open VCA
Linear VCA response
20Vpp signal handling

Notes: The tiny but mighty Eurorack power supply with all the bells and whistles

Micronova is a miniature power supply with a big soul. It can provide up to 18W of power for your modules and multiple units can be easily daisy chained to power larger systems.

This bundle includes:

an assembled Micronova
an assembled Micronova busboard
a Micronova front entry kit

Please note that the front entry requires assembly. It's a delightfully easy kit, but make sure you know what you're getting into!

A suitable AC-DC power adapter is required. We have adapters available for domestic customers. International customers please take a look at the manual for guidance and recommendations.

Check out the manual to get to know Micronova and all of the delightful ways you can integrate it into your case.

100 mm x 30 mm x 13 mm
15-20V, 1.5A
+12V @ 1A
-12V @ 300mA
+5V @ 500mA
Daisy chainable
Busboard included
Front entry kit included

Notes: A Juno-inspired oscillator module? We're flattered, but credit has to go to Roland for this one. Based on the Juno-106's digitally-controlled analogue oscillators, the Castor & Pollux modernises the 80s design with a built-in LFO and hard sync.

Supplier's Notes:
Twins that dance in and out of phase, never completely together but never fully apart, bound to each other in the infinite universe.

Castor & Pollux is a dual oscillator that echoes back to the legendary Roland Juno but shines with its own unique, massive voice. It contains two digitally-controlled analogue oscillators implemented using a faithfully modernized version of the original Juno 106 design. It builds on the classic '80s sounds of its inspiration by using the second oscillator and internal LFO to layer in thick detuned sounds and harmonically complex hard synced waveforms.

Castor & Pollux II brings a redesigned interface and moves individual waveform outputs to an included expansion. Both versions have the same features and use the same firmware.

14 HP
+12 V @ 100 mA, -12 V @ 35 mA
25 mm deep
2 separate oscillators
7 octave range
9 total outputs with waveform outputs and onboard mixers
Pitch CV input jacks (0 V to 6 V) and pitch knobs (-1 to +1 octave, configurable)
Pulse width CV input jacks and knobs
Hard sync
Hardware chorusing
Internal low-frequency oscillator (LFO)

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Designed to integrate sound sources from outside Eurorack, Verbos's Real World Interface offers three channels including built-in microphones, preamps, envelope followers and a frequency detector.

Supplier's Notes:
The Real World Interface is a 3-channel external processing module intended for connecting with sound sources outside the system. The channels are oriented as vertical channel strips. The left and right channels have a built-in condenser microphone, preamp, envelope follower with variable decay and gate extractor. In addition to a preamp, envelope follower and gate extractor, the centre channel also has an Automatic Gain Control (fixed high ratio compressor), fundamental extractor (tracking lowpass filter), frequency detector and locked oscillator. Internal microphones are useful for introducing electro acoustic room sounds into the modular. Envelope followers can be used to have external signal levels effect parameters such as filter cutoff or level for building dynamics processors. Gate extraction allows external sounds such as metronomes, clicks, claps or room sounds to advance sequencers, trigger sounds or initiate other events. The Frequency Detector can extract the pitch of simple monophonic sounds but is also a semi chaotic CV source in the tradition of such modules since their introduction in the 1960's. The Locked Oscillator plays a sine wave at the same pitch as the input signal.

Size: 18HP

Notes: Designed to integrate sound sources from outside Eurorack, Verbos's Real World Interface offers three channels including built-in microphones, preamps, envelope followers and a frequency detector.

Supplier's Notes:
The Real World Interface is a 3-channel external processing module intended for connecting with sound sources outside the system. The channels are oriented as vertical channel strips. The left and right channels have a built-in condenser microphone, preamp, envelope follower with variable decay and gate extractor. In addition to a preamp, envelope follower and gate extractor, the centre channel also has an Automatic Gain Control (fixed high ratio compressor), fundamental extractor (tracking lowpass filter), frequency detector and locked oscillator. Internal microphones are useful for introducing electro acoustic room sounds into the modular. Envelope followers can be used to have external signal levels effect parameters such as filter cutoff or level for building dynamics processors. Gate extraction allows external sounds such as metronomes, clicks, claps or room sounds to advance sequencers, trigger sounds or initiate other events. The Frequency Detector can extract the pitch of simple monophonic sounds but is also a semi chaotic CV source in the tradition of such modules since their introduction in the 1960's. The Locked Oscillator plays a sine wave at the same pitch as the input signal.

Size: 18HP

Notes: An ART wavetable dual oscillator mono voice source that can be used to build polyphonic patches and multi voice patches. It generates its harmonically rich sound using two 80s vintage D/A converters to feed your filters and effect processors. VORTEX comes loaded with dozens of wavetables, plus additional user wavetables can be loaded from the front panel SD card. A detune knob controls the second VCO and adds effects from deep phasing to a sub octave. The position knob and CV input selects waves in the tables and vibrato from LFOs to create FM. Like other ART sound generators a dedicated Gate output manages the voice envelope or any modulation synced to that voice. VORTEX is a great companion to the analog ATX1 and a must for digital synthesist enthusiasts.

Size: 8HP - Depth: 40mm / 1.5"
Power: +12V 80mA / -12V 25mA

Notes: A serious bargain for anyone putting together a modular system, TipTop bundle three VCOs and the Octopus controller with their mixer, filter, dual envelopes and VCA. Great value.

Supplier's Notes:
The S2 is a promotional bundle that TipTop is offering to users, providing a 33% savings to get you started with ART. With these bundles, TipTop have included an incredible voice: the big, beefy 3 VCO stack. The bundles come in two options: Bundle S1, which uses the ART V/OCT Quantizer as a controller, and Bundle S2, which uses Octopus as a controller. In addition to the controllers, there are three ATX1 analogue oscillators, MIX7 for mixing them with plenty of headroom, and followed by TipTop's beloved 4-pole Z2040 filter that has been with them since day one; it just sounds so good. Finally, we end up with Control Path dual envelope plus VCA dynamics modules. This special price is time limited and while supplies last.

OCTOPUS is a powerhouse ART controller that takes MIDI in via the USB or DIN connector and outputs 8 ART channels with 8 velocity CV plus 8 drum triggers. Together with the ART oscillators the OCTOPUS provide unprecedented simplicity connecting the modular to your computer sequencers, hardware midi sequencers and keyboards. Each ART channel can play polyphonic notes, monophonic notes or create multi-channel polyphony using an internal voice manager. All together OCTOPUS can play more voices and notes from a single controller than ever was possible in modular. Using ART high speed control signals OCTOPUS can maintain low jitter for tight timing. OCTOPUS is TipTop's first ART controller with more to follow, please select between Octopus or ART V/Oct Quantizer to get started with ART. Please note, OCTOPUS is not a 1V/Oct midi to CV and should not be confused as one.

Size: 18HP - Depth: 40mm / 1.5"
Power: +12V 140mA / -12V 100mA

ATX1: a classic all analogue saw VCO core with 3 switchable modes, ART, 1V/Oct, LFO and is recommended as the basic building block for ART systems. It is designed for patching analogue polyphonic synths from discrete modules or multi-mono patches in ART mode. When using ART the ATX1 takes care of the tuning including accounting for temperature changes. In 1V/Oct mode the ATX1 runs as a standard old school modular VCO. LFO mode drops the frequency range and is great for patching vibrato to other ATX1s among other things. The ATX1 outputs variable waveshapes with manual or CV control. Classic FM, PWM and hard sync are provided. A dedicated Gate Out in ART mode manages the voice envelopes or any modulation synced to that voice. TipTop consider the ATX1 the best sounding analogue VCO they have ever created.

Size: 8HP - Depth: 40mm / 1.5"
Power: +12V 105mA / -12V 33mA

MIX7 is a seven channel analogue summing mixer module for Eurorack. It is designed for summing any of the different types of signals you'll find in a modular system: Audio, CV, Triggers, or Gate.

MIX7 gives ability to sweeten your mix with more headroom using the power of low noise analogue summing. A compact 3HP Eurorack utility module, MIX7 is an attractive mixing addition to any rig, especially with the ability to also combine rhythms, note patterns or CV automations from different control sources. The main output of one section can be connected to the input of another MIX7 to create larger mixing groups and complex signal routes inside your modular.

The MIX7 summing mixing circuit is built with low-noise operational amplifiers, giving it an excellent sound quality for mixing audio, the beautiful texture of classic analogue mixing with plenty of headroom to handle hot modular signals, and the versatility to sum non-audio signals in your system to open up new creative possibilities.
Each input is labelled with a number of dots, 1-7, yellow for input and green for output. The module matches Tiptop's system look with clean white faceplate styling.

At the back of the module is a user-configurable jumper allowing users to configure the MIX7 for either unity gain (OUT = IN) or give increased headroom (OUT = 0.4IN) for use with hot audio signals, which makes it a great pairing for Tiptop Audio percussive modules. A peak indicator light on the front panel warns the user of even the slightest audio clipping in the mix, helping to keep all the incoming sound sources at their full original quality.

Size: 3HP - Depth: 43mm - Power: +12V 25ma / -12V 20ma

CONTROL PATH is an all in one voice dynamics module that helps build full voices quickly. It contains two analogue envelopes with velocity cv, and one VCA. In a typical voice patch the left envelope will control a filter and the right envelope will be the voice VCA. Velocity control is provided for each envelope and delay front panel trimmers are used to compensate for any miss match between incoming gate signal and velocity CV timings. Envelope cv outs are 0-5V, Velocity cv ins are 0-5V.
Size: 8HP - Depth: 40mm / 1.5"

Power: +12V 50mA / -12V 55mA

The Z2040 is TipTop#s redesign of the most famous analog filter from the polysynths of the 80's and features Tiptop Audio's signature lush, big, and creamy sound. Its frequency sweeps make thick bass lines and leads with great dynamics. When modulated with audio frequencies through its various inputs, the Z2040 gets quite colorful and is capable of creating many new sounds and textures as the forces of the incoming waves and their harmonics blend through the filter's non-linear circuit. When set with Resonance feedback fully up, the Z2040 transforms into a pure sine-core VC-Oscillator, great for making snappy percussive elements and whistling sounds.

A look under the hood will find that the heart of the Z2040 is a discrete design 4-pole low pass filter with a core similar to that of the SSM2040 filter chip, used in the 80's Prophet 5 Rev 2 synthesizer, and its brother the SSM2044, used in the famous early EMU samplers and PPG synthesizers of the 80's. Both filters are considered by many to be, "the best sounding filter ever".

The Z2040's four modulation inputs are built to handle CV and audio signals, enabling deep modulation of the filter core and passing signals. A VC resonance input is provided to modulate and even clip the sine wave produced by the filter feedback loop. A Frequency Modulation input (FM) provides dynamic filter sweeps and the unique VC-FM index allows modulation of the incoming FM signals. On top of that, the Z2040 comes with an audio VCA that can be configured to act upon the input or the output of the filter.

Size: 8HP - Depth: 42mm - Power: +12V 20ma / -12V 20ma

Notes: The S1 is a promotional bundle that Tiptop Audio is offering to users, providing a 33% savings to get you started with ART. With these bundles, this incredible voice is included: the big, beefy 3 VCO stack. The bundles come in two options: Bundle S1, which uses the ART V/OCT Quantizer as a controller, and Bundle S2, which uses Octopus as a controller. In addition to the controllers, there are three ATX1 analogue oscillators, MIX7 for mixing them with plenty of headroom, and followed by the beloved 4-pole Z2040 filter that has been with TipTop since day one; it just sounds so good. Finally, we end up with Control Path dual envelope plus VCA dynamics modules. This special price is time limited and while supplies last.

ART QUAD QUANTIZER is a four channel CV to ART Quantizer to play ART oscillators from CV sequencers, LFOs and anything that outputs CV. This is Tiptop's second ART controller option and is designed for those of us playing ART without a computer or MIDI source. The inputs take in positive, negative, bipolar CV voltages. Scales include Major Minor and the five other modes (Dorian, Lydian, etc). The module is simple to set up with a simple menu and one knob with switch for navigation. The 4th channel can be set to generate Chords and polyphonic note streams for ART Polyphonic oscillators.

Size: 8HP - Depth: 40mm / 1.5"
Power: +12V 38mA / -12V 4mA

ATX1: a classic all analogue saw VCO core with 3 switchable modes, ART, 1V/Oct, LFO and is recommended as the basic building block for ART systems. It is designed for patching analogue polyphonic synths from discrete modules or multi-mono patches in ART mode. When using ART the ATX1 takes care of the tuning including accounting for temperature changes. In 1V/Oct mode the ATX1 runs as a standard old school modular VCO. LFO mode drops the frequency range and is great for patching vibrato to other ATX1s among other things. The ATX1 outputs variable waveshapes with manual or CV control. Classic FM, PWM and hard sync are provided. A dedicated Gate Out in ART mode manages the voice envelopes or any modulation synced to that voice. TipTop consider the ATX1 the best sounding analogue VCO they have ever created.

Size: 8HP - Depth: 40mm / 1.5"
Power: +12V 105mA / -12V 33mA

MIX7 is a seven channel analogue summing mixer module for Eurorack. It is designed for summing any of the different types of signals you'll find in a modular system: Audio, CV, Triggers, or Gate.

MIX7 gives ability to sweeten your mix with more headroom using the power of low noise analogue summing. A compact 3HP Eurorack utility module, MIX7 is an attractive mixing addition to any rig, especially with the ability to also combine rhythms, note patterns or CV automations from different control sources. The main output of one section can be connected to the input of another MIX7 to create larger mixing groups and complex signal routes inside your modular.

The MIX7 summing mixing circuit is built with low-noise operational amplifiers, giving it an excellent sound quality for mixing audio, the beautiful texture of classic analogue mixing with plenty of headroom to handle hot modular signals, and the versatility to sum non-audio signals in your system to open up new creative possibilities.

Each input is labelled with a number of dots, 1-7, yellow for input and green for output. The module matches Tiptop's system look with clean white faceplate styling.

At the back of the module is a user-configurable jumper allowing users to configure the MIX7 for either unity gain (OUT = IN) or give increased headroom (OUT = 0.4IN) for use with hot audio signals, which makes it a great pairing for Tiptop Audio percussive modules. A peak indicator light on the front panel warns the user of even the slightest audio clipping in the mix, helping to keep all the incoming sound sources at their full original quality.

Size: 3HP - Depth: 43mm - Power: +12V 25ma / -12V 20ma

CONTROL PATH is an all in one voice dynamics module that helps build full voices quickly. It contains two analogue envelopes with velocity cv, and one VCA. In a typical voice patch the left envelope will control a filter and the right envelope will be the voice VCA. Velocity control is provided for each envelope and delay front panel trimmers are used to compensate for any miss match between incoming gate signal and velocity CV timings. Envelope cv outs are 0-5V, Velocity cv ins are 0-5V.

Size: 8HP - Depth: 40mm / 1.5"
Power: +12V 50mA / -12V 55mA

The Z2040 is TipTop's redesign of the most famous analogue filter from the polysynths of the 80's and features Tiptop Audio's signature lush, big, and creamy sound. Its frequency sweeps make thick bass lines and leads with great dynamics. When modulated with audio frequencies through its various inputs, the Z2040 gets quite colourful and is capable of creating many new sounds and textures as the forces of the incoming waves and their harmonics blend through the filter's non-linear circuit. When set with Resonance feedback fully up, the Z2040 transforms into a pure sine-core VC-Oscillator, great for making snappy percussive elements and whistling sounds.

A look under the hood will find that the heart of the Z2040 is a discrete design 4-pole low pass filter with a core similar to that of the SSM2040 filter chip, used in the 80's Prophet 5 Rev 2 synthesizer, and its brother the SSM2044, used in the famous early EMU samplers and PPG synthesizers of the 80's. Both filters are considered by many to be, "the best sounding filter ever".

The Z2040's four modulation inputs are built to handle CV and audio signals, enabling deep modulation of the filter core and passing signals. A VC resonance input is provided to modulate and even clip the sine wave produced by the filter feedback loop. A Frequency Modulation input (FM) provides dynamic filter sweeps and the unique VC-FM index allows modulation of the incoming FM signals. On top of that, the Z2040 comes with an audio VCA that can be configured to act upon the input or the output of the filter.

Size: 8HP - Depth: 42mm - Power: +12V 20ma / -12V 20ma

Notes: OCTOPUS is a powerhouse ART controller that takes MIDI in via the USB or DIN connector and outputs 8 ART channels with 8 velocity CV plus 8 drum triggers. Together with the ART oscillators the OCTOPUS provide unprecedented simplicity connecting the modular to your computer sequencers, hardware midi sequencers and keyboards. Each ART channel can play polyphonic notes, monophonic notes or create multi-channel polyphony using an internal voice manager. All together OCTOPUS can play more voices and notes from a single controller than ever was possible in modular. Using ART high speed control signals OCTOPUS can maintain low jitter for tight timing.

Please note, OCTOPUS is not a 1V/Oct midi to CV and should not be confused as one.

Size: 18HP - Depth: 40mm / 1.5"
Power: +12V 140mA / -12V 100mA

Notes: CONTROL PATH is an all in one voice dynamics module that helps build full voices quickly. It contains two analogue envelopes with velocity cv, and one VCA. In a typical voice patch the left envelope will control a filter and the right envelope will be the voice VCA. Velocity control is provided for each envelope and delay front panel trimmers are used to compensate for any miss match between incoming gate signal and velocity CV timings. Envelope cv outs are 0-5V, Velocity cv ins are 0-5V.

Size: 8HP - Depth: 40mm / 1.5"
Power: +12V 50mA / -12V 55mA

Notes: A classic all analogue saw VCO core with 3 switchable modes, ART, 1V/Oct, LFO and is recommended as the basic building block for ART systems. It is designed for patching analog polyphonic synths from discrete modules or multi-mono patches in ART mode. When using ART the ATX1 takes care of the tuning including accounting for temperature changes. In 1V/Oct mode the ATX1 runs as a standard old school modular VCO. LFO mode drops the frequency range and is great for patching vibrato to other ATX1s among other things. The ATX1 outputs variable waveshapes with manual or CV control. Classic FM, PWM and hard sync are provided. A dedicated Gate Out in ART mode manages the voice envelopes or any modulation synced to that voice. TipTop consider the ATX1 the best sounding analogue VCO they have ever created.

Size: 8HP - Depth: 40mm / 1.5"

Power: +12V 105mA / -12V 33mA

Notes: ART QUAD QUANTIZER is a four channel CV to ART Quantizer to play ART oscillators from CV sequencers, LFOs and anything that outputs CV. This is TipTop#s second ART controller option and is designed for those of us playing ART without a computer or MIDI source. The inputs take in positive, negative, bipolar CV voltages. Scales include Major Minor and the five other modes (Dorian, Lydian, etc). The module is simple to set up with a simple menu and one knob with switch for navigation. The 4th channel can be set to generate Chords and polyphonic note streams for ART Polyphonic oscillators.

Size: 8HP
Depth: 40mm / 1.5"
Power: +12V 38mA / -12V 4mA

Notes: ***B-STOCK: Without original box, product in perfect working order***


Gate Expander for Sweet Sixteen mkII.

This is an expander, brings 8 gate inputs for the Sweet Sixteen mkII.

The panel is reversible, so jacks & buttons can be in the left or right side.

The orientation of the 10 pin ribbon cable is marked by the 'do not plug power here!' legend on the PCB, so it could be with the red stripe facing that in both GESS and Sweet Sixteen mkII modules.

Notes: VastWave is a complex analogue Oscillator with advanced waveshaping capabilities that invites new textural and harmonic exploration beyond subtractive synthesis principles.

Crossfading between harmonically rich folded waveforms and waveforms with Odd/Even harmonics, the VastWave waveshaper expands on the Principal Oscillator heritage, bringing an additional set of waveforms with Odd and Even harmonics and a pulse waveform derived from the Waveshaper's Final output stage.

Furthermore the linear FM input has a dedicated VCA for external FM amplitude modulation and an on board linear Glide delivers a more musical approach to this classic feature.

Features:

Voltage controlled complex waveshaping.
Triangle core.
FM input with voltage controlled amplitude for FM amplitude modulation.
On board linear Glide.
Voltage controlled Pulse-width modulation for Pulse and Final Pls waveforms.
Modern temperature and tuning stability.
High Frequency (VCO) or Low Frequency (LFO) operation.
External Timbre input with sine wave normalization if no external source is patched.
Attenuator/inverter knobs on all voltage controlled inputs.
Inverted or double Sawthooth waveform (selectable by jumper).


Specs:

Width: 16HP
Depth: 33mm
Power consumption: ###mA +12 / ###mA -12
Eurorack Format
Doepfer power connection

Notes: SkipLog, a probability processor with sequence capturing and looping features, along a range of other versatile functions waiting to be explored.

SkipLog is a 3-channel rhythmic probability processor designed for inventive rhythmic exploration in modular setups. Introduce unpredictable rhythmic possibilitis to your creative flow.
SkipLog's basic operation is simple: when a trigger or gate is received at one of its three channels' inputs, the same channel’s Probability knob allows you to control the likelihood of these triggers or gates reaching the output. This inputs are internally connected .

SkipLog continuously captures the binary outcomes of its use, storing them for potential sequences. Activate the Loop function to break from pattern creation and loop the recorded sequences. Individual Loop Length knobs for each channel allow adjustment of the loop sizefrom 1 to 16 or 32 steps (as selected on the back), providing evolving rhythmic patterns.

To fine-tune your arrangement, SkipLog introduces functions like Mute for real-time channel silencing, Inv for signal inversion, and Choke for establishing channel priorities. Lastly, the G/T (Gate/Trigger) Mode enables users to specify whether the channel output is a gate or a trigger.

Dimensions
8 HP
33 mm deep

Current Draw
100 mA +12V
22 mA -12V

Notes: The OpticTone is a combination of a 12dB multi-mode Vactrol Filter and a Vactrol Voltage Controlled Amplifier.

It is a completely original circuit inspired by the singular nature of Vactrols and their fluid and natural character.

The Filter section provides the three fundamental filter types: Lowpass, Bandpass and Highpass.

A Resonance knob with voltage control input is available for improved modulation flexibility. The feedback knob interacts with the Resonance path, tempering it from creamy resonance to wacky self-oscillation.

Filter and VCA run in parallel, both are controlled by the Freq/Amp knob and it's associated voltage-control input. The combination of both signals can be crossfaded with a dedicated knob.

The Freq/Amp is also controlled with direct touch control on the panel via the 3 lines below the knob.

The filter frequency control can be inverted by the Inv Freq switch, providing the possibility to change the filter direction. This feature allows the filter to "close" when the VCA is "opening" or the other way around.

The Ping input allows to generate the well known vactrol filter percussive sounds if a gate or trigger signal is provided. The Ping frequency if controlled by the Freq/Amp knob, ranging from low kicks drums to high pitch bongos.

There is also a Drive knob to take care of your saturation needs. The Overdrive range is wide, from soft textural clipping to heavy distortion.

All voltage controlled inputs have an attenuator-inverter knob.

Features:

Vatrol based 12dB multi-mode Voltage Controlled Filter: Lowpass, Bandpass and Highpass.
Vactrol Based Voltage Controlled Amplifier.
Crossfade between VCF and VCA section.
Voltage controlled Resonance.
Ping Input for percussive sounds generation.
Cutoff Frequency polarity inversion switch. Doesn't change VCA polarity
Overdrive and Feedback controls.
Attenuator/inverter knobs on all voltage controlled inputs
Touch control over Frequency and Amplitude.


Specs:

Width: 10HP
Depth: 33mm
Power consumption: 55mA +12 / 55mA -12
Eurorack Format
Doepfer power connection

Notes: Designed with versatility in mind, MapVolt is a dual-channel Universal Voltage Processor built for flexibility in handling audio and CV signals.

With only 6hp, Mapvolt is a multipurpose tool for voltage-controlled scaling, inverting, offsetting, subtracting, and mixing functions.

Each channel of MapVolt can operate in either Polarizer or Attenuator mode, allowing manual control via knobs or CV signals. In Polarizer mode, it functions as a Voltage Controlled Attenuator-Inverter, granting control over signal level and polarity. Additionally, it can be used as a Four-Quadrant Multiplier or Ring Modulator for audio signals, with the processor input serving as the carrier signal and the polarizer's CV input acting as the modulator.

In Attenuator mode, MapVolt operates as a VCA, providing control over signal levels. Its VCA CV input range of +5/-5 makes it well-suited for amplitude modulation (AM) with other +/-5V waveforms.

MapVolt is equipped with dedicated Voltage Offset knobs for each channel, which can be controlled via CV. If no input is patched into the Processor input channel, the Voltage Offset knobs can be used as Offset Generators.

With its dedicated mixing stage, MapVolt enables the combination of both channels into a shared output. Furthermore, if one of the processor channels is inverted, it allows for the subtraction of one signal from the other.

Dimensions
6 HP
33 mm deep

Current Draw
65 mA +12V
65 mA -12V

Notes: The module was named Kuzmin Filter in the past as a tribute to the developer of the Polivoks, Vladimir Kuzmin. For certain reasons, the module will now be called GRUNGE Filter (due to the sound), with the circuitry remaining unchanged.

The Polivoks was a Russian synth that was produced between 1982 and 1990.This module is the AE version of the filter that gave the Polivoks a unique, rough sound.

Beyond the basic design, this filter offers some additional features:

Two different resonance characteristics, hard and soft
An FM function, that adds the input signal to the modulation of the filter
An optional overdrive for the output, making the sound even more rough and untamed.

Notes: XMIX is a swiss knife for signal mixing and attenuating, offering four(!) mixers and two attenuators in a 1U module. It is designed especially with very small AE systems in mind.

You get:

A three channel mixer "A" with knobs
a passive mixer "B" with four channels
two four-channel mixers "C" and "D" with full level / one-third-level inputs
two attenuators with seven different attenuation levels

All mixers can be used / switched for audio and CV signals.

Notes: With the STOMP-IO module, you can integrate guitar effect pedals and similar devices into your AE modular system! For output (send) and input (return) return there is a mono minijack socket; two minijack to 1/4" socket adapters are included as effect pedals usually work with the latter ones. Send and return levels can be controlled with separate knobs.

Notes: Unique, vintage reverb sound.

The SPRINGREVERB module brings the unique sound of this quite old (introduced in the 60's) technique for creating reverbs to the AE modular.

The reverb works by sending the audio signal to a set of 3 springs; at the other end of the springs the sound is picked up by a transducer, converting the mechanical movement of the springs back into an electrical signal. When the audio signal arrives at the end of the springs, the waves are reflected several times; these reflections create the reverb sound.

The spring "tank" (a metal box containing the springs and transducers, size approx. 24 x 9 x 3.5 cm) is connected externally by a cable.

The product contains all components: The module itself, the spring tank and the connection cable.

Note: The sound of a spring reverb is quite unique and has a strong vintage character; if you are looking for a more "clean", natural sounding reverb please take a look at the MULTIFX module.

Notes: DRONX is a special mixer designed especially for the DRONE38 module; if has 6 input channels (so you can connect two DRONE38 modules) and offers some sound processing capabilities: A tone control with bass and treble control, a distortion, and finally a dual delay with different algorithms. Two insert points allow to add up to two more audio effects to the internal signal chain. Together with the DRONE38 module(s) you get a quite nice drone synth for dense, dark soundscapes.

Of course, it can be used with any other sound sources!

Notes: The DIODEFILTER is an adaption of the well-known diode ladder filter that became most popular by Roland's TB-303 bassline. And here it is for the AE modular!

Notes: The CVSHIFTER module is the AE version of the well-known analogue shift register modules that are around in the modular world since a long time. It works like this: The CV input is sampled with each trigger input signal and this CV is sent to the CV 1 output; at the same time, all CV outputs 1-4 are shifted by one.

Compared to the "classic" circuits, this module is digital based and therefore doesn't suffer from drift as some analogue ASRs and S&Hs do. The result is, that you can e.g. control the pitch of up to four oscillators which is a first step into polyphony.

The CVSHIFTER module offers three modes:

Classic: Each trigger shifts the CV outs by one position, the new CV goes to output CV 1
Cycle: Each trigger sends the CV to the next output channel, restarting at out 1; additionally a gate signal at the according output.
Random: The CVs are sent in random order to one of the four outputs, plus a gate at the according output.

Notes: The classic ADSR envelope with CV control for all parameters

The ADSR module offers the classic four-stage envelope (Attack, Decay, Sustain, Release) that is not only loopable (patch the end output into gate input) but also accepts CV control over each of the stages! For the time values (A, D, R) the value set by the knob can be increased to five times the duration by the corresponding CV value. For the Sustain value the knob and CV value are simply added.

Notes: ***B-STOCK: Box opened, product in perfect working order***


A LS1lightstrip but in THREE fat dimensions!

A matrix of awesome and a powerful and unique CV controller for your system.

LP1lightplane is an expanded, tri-dimensional LS1 lightstrip. The same functions are exposed on either axis plus pressure (z) for three times the fun!

Notes: Pont-Neuf is an adapeor module which converts between eurorack jacks (3,5mm / 1/8") jacks and banana plugs, providing a simple link between eurorack and Serge 4U systems. The module provides 8 bidirectional channels, is superslim and passive, i.e. does not require a power connection. It does provide a GND-banana-jack to establish a common ground between the systems.

Dimensions:
10 HP
24 mm deep

Notes: The Serge GTS is a complete redesign of the famous Serge Dual Universal Slope Generator (DUSG) by Serge himself - with a new core, optimized for speed and tracking. Like some of the clones it can be used for CV, but also provides exceptional audio performance: transient rise times as fast as 13us and a maximum cycle speed of 27kHz.

Some functions for which one Slope Generator can be used:

Function generator for linear, logarithmic, exponential, stepped etc. curves
Integrate an incoming signal
Sawtooth / Pulse oscillator
Add, subtract up to 4 signals
Max and Min function
VC Transient Envelope Generator
VC LFO
VC Portamento device, Envelope Follower (Detector), VC Pulse Delay (Monostable), Sub-Harmonic Series Generator (Divider), Audio Oscillator with variable waveform symmetry (saw to triangle), Non-Linear Audio Processor (low-fidelity VCF).
Serge GTS for eurorack:

Designed by Serge Tcherepnin 2021-2023
Increased audio range (up to >28kHz)
Tracks >5 octaves as a Sawtooth / Pulse oscillator
Temperature stabilized
Eurorack format (3U), 26 hp
Power consumption: 90mA @ +12V, 80mA @ -12V
(NEW) Skiff-friendly: < 25mm (1")

Notes: The Serge GTO is a newly designed, complex multi-functional module which can be patch programmed to provide various slew and sample functions both for audio and CV signals, but also act as a (dual) oscillator or filter or bitcrusher or ... It is one of the essential Serge modules. The GTO is an offspring of the famous Serge SSG.

The Smooth section will place a positive and negative slew on input voltage transitions for lag effects, voltage controlled portamento and for low frequency filter applications. In Cycle-mode (cycle jack patched to the input), the Smooth side “will oscillate yielding a voltage controlled triangle wave LFO. A high level into the HOLD input will enable the Smooth Function to be used as a track-and-hold circuit with voltage controlled slew rate.

The Stepped function can be used as a sample-and-hold with voltage controlled slew rate limiting. In Cycle mode, a pulse applied to the Sample input will generate complex staircase waveforms for control voltage applications and for use as audio signals.

Each side has a temperature-compensated 1V/Oct input for use as an oscillator with a frequency range of up to 20kHz (left) and 8kHz (right). Each side tracks over 5 or 6 octaves.

The Coupler is an internal comparator which compares the output levels of the Smooth and the Stepped Generators. This output is useful for generating complex control voltages or random voltages.

Dimensions:
18 HP
25 mm deep

Current draw:
45 mA +12V
40 mA -12V

Notes: Uni is a triple attenuverter utility module designed to give cases gigantic macro control knobs.

Inputs:

CV inputs 1 and 3 - CV input for bidirectional attenuation. When input cables aren't plugged into these jacks, 5v reference signals will be used.
CV input 2 - CV input for either unidirectional or bidirectional attenuation. When an input cable isn't plugged into this jack, a 5v reference signal will be used.
Switch - toggles CV input 2 between unidirectional and bidirectional attenuation.

Outputs:

CV outputs 1, 2 and 3 - attenuated CV output. If no cables are plugged into an output jack, it is summed into the subsequent output jack.

25 mA +12V 20 mA -12V 0 mA 5V
10 HP 27mm deep

Notes: Cleverly designed melodic looping sequencer/sampler, offering four pattern banks each with 16 steps, aiming to bring 'DAW-style' workflows to Eurorack - sample reversing, pitch shifting, and so on.

Suppliers notes:
Torus is an overdub looper for harmonic playback. It offers four, 16-step pattern banks for sequencing as well as other sample manipulation techniques. It was designed to bring daw recording workflows (sample reversing, pitch shifting, sequencing, etc.) to eurorack cases.

Inputs:

A, B, C, D - buttons for choosing the current pattern. When combined with chain, these buttons can be used to sequence a pattern chain. Individual chains can be support 16 steps and are kept in sync with torus's global clock.

Chain - button for chaining behaviours. Chain + A, B, C, D can be used to sequence a pattern chain. Chain + record can be used to record multiple patterns in series and then chain playback. Chain + clear can be used to clear all recorded patterns. Chain + tap can be used to reset the current pattern when it contains recordings.

Mix - knob and CV used to blend between the input signal and the recorded pattern.

Record - button and gate in for turning on and off recording. When a pattern is not recorded, record will turn on and in sync with the clock. When a pattern is recorded, record will immediately turn on and off overdubbing.

Oct - buttons for octave shifting pattern buffer playback. Oct buttons can be used to clock divide/multiply an input clock signal.

Reverse - button and gate in for reversing buffer playback.

Harm - knob and CV for choosing harmonic pattern playback speeds. Playback speeds include both integer clock multipliers and perfect intervals.

Tap - button for tapping in tempos for the internal clock. Tap will repeat the current note when the current pattern contains recordings. Combine with chain to reset the entire pattern when the current pattern contains recordings.

Clear - button and gate in for clearing the current pattern. Combine with chain to clear all recorded patterns.

Clock - gate in for clock syncing

In L and in R - audio input, left will be converted to stereo if there is no right input.

Outputs:

Harm out - gate output mapping to harmonic playback resets. This gate output will range from 1-16x the clock out frequency depending on the harm knob/CV value.

Clock out - gate output for the global clock. The output gate frequency will be 0.25-4x the input clock speed based on the oct button state.

Reset - gate output when the current pattern has reset.

Out L and out R - audio output

100 mA +12V 40 mA -12V 0 mA 5V

16 HP 35mm deep

Notes: Monolith is a pitch-shifter reverb inspired by west coast synthesis techniques. It utilizes a time-domain based FM algorithm that acts as a shimmer.

Inputs:

In L and In R - audio input, left will be converted to stereo if there is no right input
Blend - knob and CV for controlling the fade between the dry and FM audio signals
DJ filter - knob and CV for controlling the reverb delay line filtering
Wet - knob and CV for controlling the reverb decay
Mod - knob and CV for controlling the scale of FM modulation. Low mod values correspond with microtonal pitch regions. High mod values correspond with multiple octave shifts.
On - button and CV gate for toggling on/off FM modulation. When FM modulation is turned on/off, the FM modulator oscillator is reset.
Quant - button and CV gate for toggling on/off FM pitch quantization.
Freq and v/oct - knob and CV for controlling the frequency of the FM modulator oscillator. Also control reverb pre-delay.
Shape - knob and CV for controlling FM modulator oscillator shape. Shape wavetable transitions from sine wave (8 o'clock) to triangle wave (12 o'clock) to square wave (4 o'clock).
Clock - CV gate for tempo syncing modulator oscillator period.

Outputs:

Out L and out R - audio output
Gate - CV gate out that is period synced with the FM modulator oscillator

100 mA +12V 40 mA -12V
14 HP 35 mm deep

Notes: Dizygote is an A-side/B-side digital oscillator with a built-in envelope generator. The A-side builds harmonies with a square waveform and frequency modulation. the b-side distorts a sine waveform with phase modulation.

Inputs:

Trig - button and gate in to trigger oscillator amplitude envelopes
Switch - button and gate in for toggling between the a and b sides
Length - knob and CV in for changing the envelope length
Mod - knob and CV in for changing the phase and fm modulation amounts
Mfreq - knob and CV in for changing the phase and fm modulation frequencies
Freq - knob for setting the oscillator frequency
V/oct - voltage per octave CV for modulating the oscillator frequency

Outputs:

Out L and out R - audio output
Env - CV envelope out

Notes: ***B-STOCK: Box opened, product in perfect working order***


Record. Mangle. Destroy.

Nebulae is a granular sampler and DSP platform. Its phase vocoder audio engine provides elastic audio, which can be time stretched, granularized, and mangled to no end. With independent control over pitch and speed, and granular controls such as overlap, window, and density, finding new sonic territory is only a knob turn away. Nebulae can use live audio input, a recorded buffer, or audio files as the source material for its powerful audio manipulations. The live input buffer can record up to five minutes of stereo audio at 48kHz, 24 bit. In addition, up to 75 MB of stereo audio can be loaded simultaneously through the USB port. No naming convention or special formatting necessary; just plug and play.

Nebulae lives a double life as an open source DSP platform with an extensive library of off the shelf alternate instruments. You can turn the module into a lush reverb, spectral delay, or tape-style looper simply by loading a new file onto the flash drive. Do you want to tweak one aspect of an existing instrument, even the default functionality? No problem. No prior coding knowledge is necessary to tweak and refine existing firmware to your liking or start with one of our templates. Alternate firmware files can be written with Pure Data, Csound, SuperCollider, and even bare-bones C programs.

Notes: Stereo oscillator with wavemorphing, folding, and PM

"We may have just gotten the perfect Noise Engineering oscillator - in the most compact package possible." -- CDM Blog

Sinc Legio is a simple oscillator with some tricks up its proverbial sleeve. If you need some basic waveforms, Sinc has you covered - and it makes it easy to spice up those waveforms with phase modulation, wavefolding, or hard sync. Sinc pairs well with other oscillators in your system, too: hard-sync and stereo PM inputs make complex sounds easy to patch. Combine broad-ranging timbral parameters with a vintage-inspired chorus, and you're well on your way to stereo sound-design heaven in just 6 HP.

Sinc's multiple algorithms give a world of timbral possibility at the flip of a switch. Phase modulation, plucky FM, and bright and heavy modulation await. And on top of that, Noise Engineering have added a wavefolder to it. Shape and fold to your heart's content in Fold mode.

Not only is Sinc an incredible oscillator on its own, it's also part of the Legio platform. Use the included USB cable to connect to the Customer Portal and swap the firmware to any other Legio firmware, completely free, at any time. Let that sinc in!

Notes: Stereo oscillator with wavemorphing, folding, and PM

"We may have just gotten the perfect Noise Engineering oscillator - in the most compact package possible." -- CDM Blog

Sinc Legio is a simple oscillator with some tricks up its proverbial sleeve. If you need some basic waveforms, Sinc has you covered - and it makes it easy to spice up those waveforms with phase modulation, wavefolding, or hard sync. Sinc pairs well with other oscillators in your system, too: hard-sync and stereo PM inputs make complex sounds easy to patch. Combine broad-ranging timbral parameters with a vintage-inspired chorus, and you're well on your way to stereo sound-design heaven in just 6 HP.

Sinc's multiple algorithms give a world of timbral possibility at the flip of a switch. Phase modulation, plucky FM, and bright and heavy modulation await. And on top of that, Noise Engineering have added a wavefolder to it. Shape and fold to your heart's content in Fold mode.

Not only is Sinc an incredible oscillator on its own, it's also part of the Legio platform. Use the included USB cable to connect to the Customer Portal and swap the firmware to any other Legio firmware, completely free, at any time. Let that sinc in!

6HP Eurorack
+12v: 140mA
-12v: 22mA
Sinc - from Latin: "treasure"

Legio - from Latin: "legion, army"

"A lot of treasure"

Notes: Yep, it's an attenuator. With a fancy name! And LEDs!

Sinc Defero's inputs are circularly normalled, too, so you can use it as a mult by leaving inputs unpatched.

Features:

Size and power:

4HP Eurorack
+12v: 45mA
-12v: 40mA
Sinc - from Old English sinc for "treasure" and Greek clastic for "easily removable"

Defero - from Latin for "sloping down"

"Portable treasure reduction"

What's in the box:

Module
Power cable
To reduce excess materials, screws will no longer be included with Noise Engineering's modules beginning in 2023.

Notes: Four-channel arpeggiator with customizable patterns and CV control

Opp Ned is a four-channel arpeggiator designed for creating patterns that can be modified with CV. Opp Ned ships with 12 of Nosie Engineering's favourite arps, including tetrads, major, pentatonic major, minor third, and pentatonic minor, but you can edit and save custom arpeggios to twelve memory slots. Recall your custom arpeggios manually or with CV using the Ptn input. If you ever want to restore the factory arps, just head to the Noise Engineering Customer Portal.

The transpose input makes it easy to combine Opp Ned with external sequencers, too!

Arps have never been easier than with Opp Ned.

Features

Size and Power
8HP Eurorack
+12v: 60mA
-12v: 10mA

Opp from Norwegian Opp for "Up"
Ned from Norwegian Ned "down"
"Ups and downs"

What's in the box

Module
Power cable

*** Noise Engineering no longer include screws with newly packaged modules. Bulk screws are available for purchase. ***

Notes: Really nice take on an arpeggiator module here. Four-channel design features editable arpeggio patterns, CV control and transposition. Real-time performance meets customisable melody generation.

Supplier's Notes:
Four-channel arpeggiator with customizable patterns and CV control

Opp Ned is a four-channel arpeggiator designed for creating patterns that can be modified with CV. Opp Ned ships with 12 of Noise Engineering's favourite arps, including tetrads, major, pentatonic major, minor third, and pentatonic minor, but you can edit and save custom arpeggios to twelve memory slots. Recall your custom arpeggios manually or with CV using the Ptn input. If you ever want to restore the factory arps, just head to the Noise Engineering Customer Portal.

The transpose input makes it easy to combine Opp Ned with external sequencers, too!

Arps have never been easier than with Opp Ned.

Features

Size and Power
8HP Eurorack
+12v: 60mA
-12v: 10mA

Opp from Norwegian Opp for "Up"
Ned from Norwegian Ned "down"
"Ups and downs"

What's in the box

Module
Power cable

*** Noise Engineering no longer include screws with newly packaged modules. Bulk screws are available for purchase. ***

Notes: Nive Grad is a level shifter designed for simplicity. Two Eurorack signals can be attenuated down to pedal and line levels, and two external line or pedal signals can be amplified up to Eurorack level. Integrating a drum machine, external synth, effects processor, or guitar with your Eurorack system has never been easier!

Nive Grad uses 1/8" jacks to save HP. If you want to use 1/4" gear with your system, ask your modular supplier about mono/TS 1/8" to 1/4" adapters or adapter cables.

Nive Grad pairs well with Noise Engineering's Xer Mixa system mixer, but can be used in any Eurorack system.

Type: Universal drum synthesizer
Size: Level Shifter
Depth: .9 inches
Power: 2x5 Eurorack
+12 V: 25 mA
-12 V: 25 mA
5 V: 0mA
Nive - level - from Latin niveum

Grad - step or degree- from Latin Gradus

Notes: Nive Grad is a level shifter designed for simplicity. Two Eurorack signals can be attenuated down to pedal and line levels, and two external line or pedal signals can be amplified up to Eurorack level. Integrating a drum machine, external synth, effects processor, or guitar with your Eurorack system has never been easier!

Nive Grad uses 1/8" jacks to save HP. If you want to use 1/4" gear with your system, ask your modular supplier about mono/TS 1/8" to 1/4" adapters or adapter cables.

Nive Grad pairs well with Noise Engineering's Xer Mixa system mixer, but can be used in any Eurorack system.

Type: Universal drum synthesizer
Size: Level Shifter
Depth: .9 inches
Power: 2x5 Eurorack
+12 V: 25 mA
-12 V: 25 mA
5 V: 0mA
Nive - level - from Latin niveum

Grad - step or degree- from Latin Gradus

Notes: Gross, gritty, and dark industrial-strength voice on a swappable oscillator platform. Pangolin approved.

Manis Iteritas Alia is a voice based on the architecture of Basimilus. It was designed to be grittier and more aggressive by using only sawtooth waves that are manipulated, modulated, and distorted through a rethought interface. Manis Iteritas Alia is fantastic for leads, basslines, drums, darkness, detuned swarminess, or pure mayhem. Plus, MIA's dedicated envelope output is a great modulation source for the rest of your patch.

MIA is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal to check out any other Alia firmware, free of charge, any time.

A portion of the proceeds of every Manis Iteritas Alia sold goes to pangolin conservation.

Width: 10HP
Depth: 22mm

Notes: Gross, gritty, and dark industrial-strength voice on a swappable oscillator platform. Pangolin approved.

Manis Iteritas Alia is a voice based on the architecture of Basimilus. It was designed to be grittier and more aggressive by using only sawtooth waves that are manipulated, modulated, and distorted through a rethought interface. Manis Iteritas Alia is fantastic for leads, basslines, drums, darkness, detuned swarminess, or pure mayhem. Plus, MIA's dedicated envelope output is a great modulation source for the rest of your patch.

MIA is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal to check out any other Alia firmware, free of charge, any time.

A portion of the proceeds of every Manis Iteritas Alia sold goes to pangolin conservation.

Width: 10HP
Depth: 22mm

Notes: Alia is a 10HP oscillator platform much like the Versio and Legio platforms. Launched in 2023 with a reboot of the beloved Basimilus Iteritas and Manis Iteritas, along with a new oscillator, Debel Iteritas, Noise Engineering is back with three more firmwares for the platform.

Separate hardware is available for each module, and a customer with any Alia module can try any firmware for free by going to the Noise Engineering Customer Portal and connecting with the included USB cable.

Incus Iteritas Alia

FM-based wave-mangling additive voice for synthetic percussion and instruments on a swappable oscillator platform

Incus Iteritas Alia is a new member of the Iteritas family, hammering big and bold sounds into your patches. Incus started as a percussion voice, and evolved into so much more: create kicks for any genre, snares, and metallic hits, or go melodic and create FM plucks, analogue-style basslines, and so much more. Incus uses a combination of waveshaping, saturation, wavefolding, FM, and additive synthesis, plus a slew of internal modulation, all behind easy-to-use parameters perfect for jamming.

IIA is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal and check out any other Alia firmware, free of charge, any time.

Width: 10HP
Depth: 22mm

Notes: Originally designed as a percussion voice, the Incus Iteritas Alia also lends itself well to FM synth sounds, combining deep internal modulation with user-friendly front panel controls.

Supplier's Notes:
Alia is a 10HP oscillator platform much like the Versio and Legio platforms. Launched in 2023 with a reboot of the beloved Basimilus Iteritas and Manis Iteritas, along with a new oscillator, Debel Iteritas, Noise Engineering is back with three more firmwares for the platform.

Separate hardware is available for each module, and a customer with any Alia module can try any firmware for free by going to the Noise Engineering Customer Portal and connecting with the included USB cable.

Incus Iteritas Alia

FM-based wave-mangling additive voice for synthetic percussion and instruments on a swappable oscillator platform

Incus Iteritas Alia is a new member of the Iteritas family, hammering big and bold sounds into your patches. Incus started as a percussion voice, and evolved into so much more: create kicks for any genre, snares, and metallic hits, or go melodic and create FM plucks, analogue-style basslines, and so much more. Incus uses a combination of waveshaping, saturation, wavefolding, FM, and additive synthesis, plus a slew of internal modulation, all behind easy-to-use parameters perfect for jamming.

IIA is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal and check out any other Alia firmware, free of charge, any time.

Width: 10HP
Depth: 22mm

Notes: Hybrid additive phase-modulation voice on a swappable oscillator platform

Debel Iteritas Alia is a hybrid additive phase-modulation voice inspired by classic and experimental synth sounds from across the decades. Three synthesis algorithms range from classic FM plucks and basses to all-out additive anarchy. DIA features a two-parameter envelope with a huge range of shapes and timing, making it easy to dial in the exact sound you want. With CV over every parameter, a dedicated envelope output, and an absolutely massive timbral range, Debel Iteritas Alia is a powerhouse synth voice in a compact package.

DIA is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal to check out any other Alia firmware, free of charge, any time.

Width: 10HP
Depth: 22mm

Notes: Alia is a 10HP oscillator platform much like the Versio and Legio platforms. Launched in 2023 with a reboot of the beloved Basimilus Iteritas and Manis Iteritas, along with a new oscillator, Debel Iteritas, Noise Engineering is back with three more firmwares for the platform.

Separate hardware is available for each module, and a customer with any Alia module can try any firmware for free by going to the Noise Engineering Customer Portal and connecting with the included USB cable.

Cursus Iteritas Alia

Dynamically generated wavetable oscillator using orthogonal functions on a swappable oscillator platform

Cursus Iteritas Alia is Noise Engineering's take on a wavetable-inspired additive oscillator. Cursus creates sounds from a dynamically generated wavetable, then gives the user spectral controls to sculpt and modulate. Cursus has three different algorithms, based on different conceptualizations of frequency: Fourier, which uses sine waves; Daubechies, using wavelets; and Walsh mode, using the Walsh transform. All that math is hidden behind a set of friendly controls that produces an extremely wide variety of harmonic sounds, perfect for melodic sound design. Cursus has long been regarded as the gentlest Iteritas, but if you need some beef and extra low end, try mixing the suboscillator output into your patch.

CIA is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal and check out any other Alia firmware, free of charge, any time.

Width: 10HP
Depth: 22mm

Notes: Alia is a 10HP oscillator platform much like the Versio and Legio platforms. Launched in 2023 with a reboot of the beloved Basimilus Iteritas and Manis Iteritas, along with a new oscillator, Debel Iteritas, Noise Engineering is back with three more firmwares for the platform.

Separate hardware is available for each module, and a customer with any Alia module can try any firmware for free by going to the Noise Engineering Customer Portal and connecting with the included USB cable.

Cursus Iteritas Alia

Dynamically generated wavetable oscillator using orthogonal functions on a swappable oscillator platform

Cursus Iteritas Alia is Noise Engineering's take on a wavetable-inspired additive oscillator. Cursus creates sounds from a dynamically generated wavetable, then gives the user spectral controls to sculpt and modulate. Cursus has three different algorithms, based on different conceptualizations of frequency: Fourier, which uses sine waves; Daubechies, using wavelets; and Walsh mode, using the Walsh transform. All that math is hidden behind a set of friendly controls that produces an extremely wide variety of harmonic sounds, perfect for melodic sound design. Cursus has long been regarded as the gentlest Iteritas, but if you need some beef and extra low end, try mixing the suboscillator output into your patch.

CIA is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal and check out any other Alia firmware, free of charge, any time.

Width: 10HP
Depth: 22mm