100% Secure Shopping

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Secure Shopping

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

View:
Options
Items 1 to 50 of 142 on page 1 of 3
1  2  3  »
Cat: 427842 Rel: 14 Jun 11 • View all Sequencers
 
MIDI/USB analog sequencer with red LEDs (240V only)
Notes: Dark Time is an 2x8 step analog sequencer with CV/Gate, USB and MIDI interface. It is intended as an add-on for the Dark Energy but may be used in combination with other MIDI, USB or CV/Gate equipment too.
Read more
 3 in stock $480.55
Cat: 671550 Rel: 29 Nov 17 • View all Synth modules
 
VCO module featuring four precision oscillators - 18HP
Notes: A-111-4 contains four precision VCOs and has individual controls, inputs and outputs for each VCO available as well as a common control and output unit. After all the A-111-4 is very similar to four A-111-3 without LFO mode but built in output mixers for the three waveforms, and a master unit for all four VCOs.

Controls, inputs and outputs for each of the four VCOs:

- 1V/Octave CV input
- Octave switch (+1 / 0 / -1 octave)
- Tune control (range internally adjustable by jumpers: ~ 2 semitones / ~ 1 octave / ~ 4 octaves)
- Modulation CV input
- Modulation destination:
- Upper position: exponential frequency modulation (XM)lower position: linear frequency modulation (LM) or pulsewidth modulation of the rectangle (PM), selectable via internal jumper
- Frequency Modulation (FM) or Pulsewidth Modulation of the rectangle (PWM)
- Modulation intensity
- Triangle output
- Sawtooth output
- Rectangle output (about 50% without external PWM)
- Sync input (hard or soft sync internally selectable via jumper, CEM3340 hard sync type)
- Min. 10 octaves range (with appropriate external CV)
- CEM3340 based VCO (triangle core)
- Each VCO has it's own separate internal +/- power supply for each for best stability and the prevention of unwanted synchronisation of the VCOs

Controls, inputs and outputs of the master section:

- 1V/Octave CV input
- Octave switch (+1 / 0 / -1 octave)
- Tune control (range internally adjustable by jumpers: 2 semitones / 1 octave / 4 octaves)
- Frequency Modulation CV input (FM)
- FM intensity
- Triangle sum output
- Sawtooth sum output
- Rectangle sum output
- As soon as the single waveform output of a VCO is patched this waveform of the VCO in question is removed from the sum (this function can be turned off for each single output socket by means of solder bridges on the pc board, i.e. the sum contains then all signals independent of the patching of the single output)
- CV output (outputs the sum CV that is used to control all four VCOs)
- Bus CV (selectable via jumper)

Typical applications:

- Fat sounding monophonic VCO with the possibility to adjust any intervals
- Paraphonic patches in combination with the polyphonic CV interface A-190-5 (all four VCOs processed by one VCF/VCA)
- Full polyphonic patches in combination with the polyphonic CV interface A-190-5 and four complete VCF/VCA sections
- Complex VCO patches with up to four VCOs by means of the frequency modulation features (exponential an linear) and the sync functions
Read more
 1 in stock $397.40
Cat: 671556 Rel: 29 Nov 17 • View all Synth modules
 
Octal VC/manual programmable switch - 12HP
Notes: Module A-150-8 contains eight manually/voltage controlled switches. Each of the eight switches has a manual control button (Man.), a control voltage input (CV), a common Out / Input (O/I), and two In / Outputs (I/O1, I/O2). The switches are bi-directional, i.e. they can work in both directions, so can connect one input to either of two outputs, or either of two inputs to one output. Two LEDs show which in / output is active (i.e. which is connected to the common out / input). In addition, the LEDs are used for the programming of the module:

For each unit the operating mode can be selected: Toggle or Level controlled. In Toggle mode the rising edge of the CV input or operating the manual control button changes the state of the switch. In Level mode the switch state is defined by the voltage applied to the CV input (low voltage = I/O1, high voltage = I/O2) or by the state of the manual control button (not pressed = I/O1, pressed = I/O2). The modes are programmed very easily: Operating the Toggle/Level button of the program section displays the current state of each switch with the LEDs: left LED on = Toggle mode, right LED on = Level mode. Operating the manual control button of the switch in question changes the toggle/level mode while the Toggle/Level button of the program section is operated. During the programming patched CV signals may have to be removed as the CV signals would interfere with the manual operating buttons during the programming process.

In addition, it's possible to define master/slave groups. In such a group the upper unit (= master) controls also the state of the following switches provided that they are defined as slaves. Master/slave programming is also very simple: Operating the Master/Slave button of the program section displays the current state of each switch with the LEDs: left LED on = Master, right LED on = Slave.

When all 8 units are defined as master all switches are independent from each other. If for example the sequence is MSSSMSMS the control unit of the first switch also controls the switches 2, 3 and 4. The control unit of switch 5 also controls the switch 6, and the control unit of switch 7 also controls the switch 8. The current states of the slave switches are overwritten by the state of the master switch.

Technical note: To protect the electronic switches in case of an unsuitable patch (e.g. connection of two outputs) a 1k protection resistor is inserted into the O/I line of each switch. If control voltages used for VCOs are switched this may cause a small voltage drop and lead to undesired audible detuning. For this application we recommend to insert a CV buffer between A-150-8 and the VCO(s), e.g. the Buffered Multiple A-180-3 or the Precision Adder A-185-2. Integrating the buffers into the module A-150-8 was not possible because this would ruin the bidirectionality of the switches.
Read more
 1 in stock $134.98
Cat: 671564 Rel: 29 Nov 17 • View all Synth modules
 
12dB multi-mode filter with unique classic circuitry, based on the filter from the 70s EDP Wasp synth
Notes: Module A-124 is a special 12dB multimode filter using the "strange" filter circuit of the "EDP Wasp" (an analog synthesizer with black/yellow case built end of the seventies, manufactured by the UK company "Electronic Dream Plant" with Chris Huggett und Adrian Wagner). This design "abuses" digital inverters as analog operational amplifiers leading to distortions and other "dirty" effects that generate the specific sound of this filter. The filter is equipped with a band pass output and a combined low/notch/high pass output. For this output a control knob defines the relation between low and high pass signal. If both signals appear at the same level (i.e. middle position of the Mix knob) one obtains a notch filter. Otherwise the low or high pass signal predominates. The module does not feature self-oscillation in contrast to most of the other filters of the A-100 system.

Inputs: Audio In, CV In (2x)
Outputs: Bandpass Out, Low/Highpass Mix-Out
Controls: Audio and CV attenuator, Frequency, Resonance, LP/HP Mix

The function and operation of this module is very similar to the module SEM VCF A-106-5. But the sound of both filters is very different! The only functional difference is the position of the sockets and controls, and the function of the controls CV2 (A-124: normal attenuator, A-106-5: polarizer).

- 3U Eurorack module, 8HP wide, 45mm deep
- Current draw 30mA
Read more
 8 in stock $83.10
Cat: 671576 Rel: 29 Nov 17 • View all Synth modules
 
Enhanced clock divider with multiple dividing factors - 4HP
Notes: Module A-160-2 is an enhanced version of the standard clock divider A-160. The module is a frequency divider for clock/trigger/gate signals, designed to be a source of lower frequencies, particularly for rhythm uses. The Clock input will take any digital signal from, eg. LFO, MIDI sync, or the gate from a MIDI-CV interface. At the outputs, you have access to three sets of seven different sub-divided clock signals, from half the clock frequency down to 1/128. The low/high levels of the output signals are 0V and about +10V.

The A-160-2 also has a reset input. Whenever a reset signal is sensed, all outputs are set to certain levels which depend upon the selected mode.

These are the most important features of the module:

Three different sets of dividing factors, selected by a three-position switch at the front panel:
- Power of two: 2, 4, 8, 16, 32, 64, 128
- Prime numbers: 2, 3, 5, 7, 11, 13, 17
- Integer: 2, 3, 4, 5, 6, 7, 8

Two output modes, selected by a two-position switch at the front panel:
- Gate mode: outputs act like the outputs of typical binary dividers
- Trigger mode: in this mode the outputs are AND-wired with the clock signal (i.e. the clock pulsewidth affects the pulsewidth of the outputs)
- Clock edge type selected by a jumper on the pc board:
- Positive: the rising edge of the clock signal triggers the state change of the outputs
- Negative: the falling edge of the clock signal triggers the state change of the outputs

Reset behaviour by two jumpers on the pc board:
- Level triggered: the level at the Reset input triggers the Reset
- Edge triggered: the edge of the signal at the Reset input triggers the Reset
- Positive: a high level (> 2.5V) or the rising edge at the Reset input triggers the Reset
- Negative: a low level (< 1 V) or the falling edge at the Reset input triggers the Reset

Output polarity selected by a jumper on the pc board:
- Positive: non-inverted outputs
- Negative: all seven outputs are inverted

Width: 4HP / 20mm
Depth: 35mm (Measured from the rear side of the front panel)
Current: +12V: +50mA, -12V: -0mA
Read more
 4 in stock $95.02
Cat: 671585 Rel: 29 Nov 17 • View all Synth modules
 
Module consisting of voltage-controlled low frequency oscillator (LFO) & voltage controlled amplifier (VCA) - 8HP
Notes: Module A-147-2 is the successor of the VCLFO A-147 but offers much more features than the predecessor. The module is made of these sub-units:

- VCLFO: voltage controlled low frequency oscillator
- VCA: voltage controlled amplifier, switchable to voltage controlled polarizer
- VC delay unit: voltage controlled linear attack envelope (only one parameter: attack) for delayed LFO operation in combination with the VCA (e.g. delayed vibrato/tremolo)

LFO: The voltage controlled LFO has the waveforms Triangle, Sine, Sawtooth and Rectangle available and features a Reset/Sync input. Triangle/Sine and Rectangle are displayed by means of dual-colour LEDs (probably red/green), Sawtooth has a unicolor LED available (probably blue). The output levels are about -4V...+4V for Triangle, Sine and Rectangle. The Sawtooth level is about 0...+8V.

The CV control can be switched to attenuator or polarizer ("CV Mode" switch). In polarizer mode the CV inputs affects the frequency in the reverse manner when the CV control is left from the centre position. In the centre position CV has no effect and right from the centre the control works like a normal attenuator. The frequency range (without external CV) is from about 0,005 Hz (i.e. about 3 minutes per period) to 200 Hz (with external CV max. frequency about 1kHz). In addition a ultra-low mode can be activated by means of an internal jumper. When the ultra-low jumper is set a fixed voltage is connected to the switching contact of the "LFO CV" socket. In polarizer mode of the CV control that way extremely low frequencies (up to one hour period and more) are possible. For this a jumper has to be installed on the pin header JP6. In the factory a dummy jumper is installed on the pin header JP7 "Dummy". JP7 has no function and is used only for "parking" of the jumper. Simply remove the jumper from JP7 and plug it on JP6. JP6 is located behind the CV control.

VCA: This is a linear VCA that can be switched to "normal" VCA (i.e. kind of a voltage controlled attenuator) or voltage controlled polarizer ("VCA Mode" switch). In the "normal" VCA mode amplification +1 is achieved with about +5V control voltage. In polarizer mode the amplification ranges from about -0.5 (i.e. inverted signal with about 50% level) with 0V CV to +0.5 (i.e. non-inverted signal with about 50% level) with +5V CV. With about +2.5V CV the signal is suppressed. Details about the functioning of a voltage controlled polarizer can be found in the description of the module A-133. In this mode the VCA can be treated also a DC coupled ring modulator (similar to A-114).

The VCA of the A-147-2 has three sockets available: "In" (signal input), "Out" (signal output) and "CV" (control voltage input).

The Triangle Output of the LFO is normalled to the VCA signal input by means of the switching contact of the "VCA In" socket. If another LFO waveform (or any other signal) should be processed by the VCA the corresponding signal has to be patched to the "VCA In" socket. The VCA can be used also independently from the LFO and the Delay CV. In this case the VCA sockets In, Out and CV have to be patched accordingly. The VCA can be used also as waveshaper for the LFO signals (e.g. by patching VCA In and VCA CV to different LFO signals, if necessary via attenuator A-183-1 or offset generator/attenuator A-183-2).

Attack/Delay: The third sub-unit of the module is a simple, voltage controlled envelope generator that has only the parameter "Delay" (or Attack) available. This unit generates a linear increasing voltage that starts from 0V after each Delay Reset until it reaches about +5V. Then the voltage remains at +5V until the next Delay Reset occurs. The inclination or gradient is controlled by the manual Delay control and the Delay control voltage ("Delay CV" input). The waveform is linear, the control scale is exponential. The output voltage is displayed by a green LED and available at the "Delay Out" socket.

The manual Delay control ranges - without external "Delay CV" - from about 5ms (fully CW) up to 2 minutes (fully CCW). By means of an external voltage applied to the "Delay CV" socket this range can be extended. A rising CV shortens the delay time (behaviour like a VCO)!

The Delay output voltage ranges from about 0V to +5V. The rising edge of the gate, clock or trigger signal applied to the "Delay Reset" sockets resets the Delay output voltage to 0 V.

"Delay Out" is normalled to the VCA CV input by means of the switching contact of the "VCA CV" socket and consequently controls the Triangle level provided that no other patch is made. A typical example is the usage of a Gate signal (e.g. from a USB/Midi-to-CV/Gate interface) as Delay Reset. That way a delayed vibrato or tremolo can be realized if the VCA output is patched to the frequency CV input of a VCO (or VCF), or the CV input of a VCA.
Read more
 1 in stock $123.10
Cat: 671589 Rel: 29 Nov 17 • View all Synth modules
 
Four-channel stereo mixer - 8HP
Notes: A-138s is a simple but useful 4-in-2 mixing tool. It has four inputs available. Each input is equipped with an attenuator (Level) and a panning control that is used to distribute the signal to the left and right output. Beyond stereo mixing it is equally suited to create variable parallel routings. For example: Any of the four inputs may be routed in variable intensity to feed two filters.

You may regard the A-138s as a smaller version of the A-138m Matrix Mixer.

Inputs and outputs are DC coupled, i.e. the module can be used for the mixing of control signals too.

- 3U Eurorack module, 8 HP wide, 30 mm in depth
- Power consumption: 10 mA at +12 V and 10 mA at -12 V
Read more
 5 in stock $74.50
Cat: 671591 Rel: 29 Nov 17 • View all Synth modules
 
Analog VCO/LFO module with wide frequency range - 4HP
Notes: The Micro Precision VCO is a space-saving and utterly precise analog VCO/LFO with a extremely wide frequency range, immaculate tracking over at least ten octaves and nearly perfect waveforms.

Basically, it's the same circuitry like the High-End VCO A-111-2 but with reduced functions and controls. It is suitable as a modulator for exact linear FM and much more.

The A-111-3 has two elements for setting the frequency: A switch selecting between LFO and VCO mode as well as a tune control with a jumper-selectable range:

- Jumper position 1: 16Hz to 20 kHz
- Jumper position 2: 16Hz to 70Hz
- Without jumper: 16Hz to 22Hz

The XM potentiometer can be used as a fine tune control as long as nothing is patched to the XM socket.

The oscillator has a frequency range of at least fifteen osctaves (0.0001 - 40 Hz in LFO mode; 0.5 Hz to 20 kHz in VCO mode) and offers perfect 1 V per octave tracking over ten octaves minimum, typically in the range of 20 Hz to 20 kHz. Frequencies below 25 Hz are visualized with a two-colour LED.

The 1V per octave input is accompanied by two FM inputs, one for linear and one for exponential frequency modulation. A jumper determines whether the module obtains pitch CV via the internal bus.

The VCO has a triangle core from which sawtooth, pulse and triangle are derived. The wave forms are almost perfect and sans glitches.

The pulse width can be set with a control from 0 to 100% and of course it can be modulated.

There is one input for oscillator synchronisation and its type, either hard or soft sync, is jumper-selected. Both types differ in sound with the hard sync being more aggressive and richer in harmonics.
Read more
 2 in stock $147.94
Cat: 671592 Rel: 29 Nov 17 • View all Synth modules
 
12dB multi-mode filter based on classic SEM filter circuitry
Notes: Module A-106-5 is a 12dB multimode filter that is based on the filter circuit of the Oberheim SEM module. The filter is equipped with a band pass output and a combined low/notch/high pass output. For this output a control knob defines the relation between low and high pass signal. If both signals appear at the same level (i.e. middle position of the Mix knob) one obtains a notch filter. Otherwise the low or high pass signal predominates. The module does not feature self oscillation in contrast to most of the other filters of the A-100 system. The module generates a distorted audio signal if the level control is set to about 50% (i.e. centre position) or more with A-100 standard signals like VCOs.

Inputs: Audio In, CV1 In without attenuator, CV2 In with Polarizer
Outputs: Bandpass Out, Low/Highpass Mix-Out
Controls: Audio Attenuator, CV2 Polarizer, Frequency, Resonance, LP/HP Mix

The function and operation of this module is very similar to the Wasp filter module A-124. But the sound of both filters is very different! We will publish no separate user's manual for the A-106-5 but a combined manual for both A-106-5 and A-124. The only functional difference is the position of the sockets and controls, and the function of the controls CV2 (A-124: normal attenuator, A-106-5: polarizer)

Width: 8HP / 40.3mm
Depth: 55mm (Measured from the rear side of the front panel)
Current: +12V: +30mA, -12V: -20mA
Read more
 3 in stock $89.62
Cat: 671593 Rel: 29 Nov 17 • View all Synth modules
 
Performance Mixer system input module featuring four identical input channels - 16HP
Notes: Modules A-138p/o are used to built a simple performance mixer (instead of an external stand-alone mixer). Module A-138p is the 4-fold input module, A-138o is the output module that can be combined with one or more A-138p.

A-138p features:

- 4 channels
- Controls and inputs for each channel
- Input (3.5 mm mono socket)
- Signal LED (as a coarse monitor of the incoming level, the level is measured after the gain control)
- Mute switch
- Gain (control to adapt different audio levels)
- Level (the main volume control)
- Aux
- Pan
- Internal jumper for each channel to choose between Aux pre/post main Level control
- Internal connection to the output module and to other A-138p modules

Doepfer A-138p requires A-138o (no stand-alone use).
Read more
 1 in stock $106.90
Cat: 577776 Rel: 29 Nov 17 • View all Synth modules
 
Four channel mixer module - 8HP
Notes: Module A-138 is a four channel mixer, which can be used with either control voltages or audio signals. Each of the four inputs has an attenuator, and there's a master attenuator, so that the mixer can be used at the end of the audio chain, i.e. it can be used to interface directly with an external mixer, amplifier, etc.

The A-138b has potentiometers with logarithmic response, so is especially suitable for audio signal mixing.
Read more
 3 in stock $57.22
Cat: 577754 Rel: 29 Nov 17 • View all Synth modules
 
Envelope generator with CV outputs for modulation - 8HP
Notes: Module A-140 is an envelope generator, and, since it puts out control voltages, counts as one of the modulation devices in a modular system. As soon as the gate input receives sufficient voltage, the ADSR generates a variable voltage, changing in time, called an envelope. This varying voltage is output in normal (positive) and inverted form, and can be used, eg. for voltage controlled modulation of a VCO, VCF, or VCA, or for processing other modules' inputs and outputs.

The shape of the envelope is governed by four parameters: Attack, Decay, Sustain and Release.

The envelope is started (triggered) by a gate signal either from the INT.GATE voltage on the system bus, or, if a signal is put into it, from the gate input socket.

The envelope can also be re-triggered, i.e. start from scratch again, each time a trigger signal is sensed at the Retrig. input socket, when the gate is still open.

Module A-140 has available a three-position toggle switch to select one of three time ranges. The envelope duration ranges from about 50us (microseconds) up to several minutes.

In combination with the Comparator module A-167 a free-running "ADSR-LFO" can be realized.
Read more
 1 in stock $82.06
Cat: 577745 Rel: 29 Nov 17 • View all Synth modules
 
Two sample & hold units in one module for generating stepped random voltages or slicing signals
Notes: Module A-148 (Dual S&H) has two identical sample & hold modules, designed to produce 'staircase' voltages. The signal present at the sample input is sampled at a rate set by the signal at the trigger input, and held at that voltage at the S&H output.

The exact shape of the staircase depends on the sort of waveform at the sample input: NOISE or RANDOM signals produce random patterns; an LFO produces rising or falling staircase patterns.

Two LEDs for each S&H indicate the voltage (positive or negative) of the sampled signal.
Read more
 5 in stock $64.78
Cat: 577771 Rel: 29 Nov 17 • View all Synth modules
 
Envelope follower & pre-amplifier for microphone/line-signals - 8HP
Notes: Module A-119 (External Input / Envelope Follower) is designed to allow external audio signals to be integrated into the System A-100. It comprises a pre-amp, envelope follower, and comparator.

The pre-amp has two inputs: an unbalanced input for line level signals, with a gain factor of from 0 to 20, and a balanced input with a gain factor of from 0 to 500, for insertion of low level signals, for instance from a microphone or electric guitar.

The Envelope Follower reads the signal level of the input, and puts out a proportional voltage as an envelope at its own output.

The comparator generates a gate signal whenever the input goes above an adjustable trigger threshold.

Three LED's help you keep track of overload, the envelope, and the gate signal.
Read more
 3 in stock $70.18
Cat: 577769 Rel: 29 Nov 17 • View all Synth modules
 
Standard VCO providing two CV inputs for pitch, an octave switch, four waveforms with separate outputs, pulse width modulation & hard sync - 10HP
Notes: Module A-110-1 is a voltage-controlled oscillator. This VCO's frequency range is about eight octaves (ca. 15Hz ... 8kHz). It can produce four waveforms simultaneously: rectangle, sawtooth, triangle, and sine wave (triangle and sine shapes are not perfect, see remark below). The output levels are typically 8Vpp for saw and rectangle, and 10Vpp for triangle and sine. The frequency or pitch of the VCO is determined by the position of the octave (Range) switch and tuning (Tune) knob, and by the voltage present at the CV inputs. Frequency modulation (FM) of the VCO is therefore a possibility. Footage (the octave of the fundamental) is set by the Range control in five steps, and Fine tuning controlled by the Tune knob by about +/-1 one semitone (can be modified for a wider range).

You can control the pulse width of the square wave either by hand, or by voltage control - Pulse Width Modulation or PWM.

For more detailed information please look at the user's manual A110_man.pdf. In addition, the A-110 service manual is available as an example for the A-100 service manual that is available at extra charges. This document describes also how to modify the sensitivity of the tune control, how to re-adjust the 1V/octave scale and the frequency offset (i.e. the absolute pitch). Such modifications should be carried out by experienced users only!

The core of the A-110-1 is a sawtooth oscillator (in contrast to the A-111-1, which is based on a triangle oscillator). The other waveforms are derived from the sawtooth by internal waveform converters. As the sawtooth reset (i.e. the back-to-zero slope) is not infinite fast but takes a little bit of time the derived waveforms triangle and sine are not perfect! At the top of the waveform they have a small glitch or notch that is caused by the sawtooth reset and cannot be eliminated by the waveform converters. The sine is derived from the triangle by a simple diode-based converter and the sine shape is not perfect (only a rounded triangle).

If a perfect triangle is required, the A-111-1 is recommended. For a perfect sine wave the quadrature LFO/VCO A-143-9 is recommended.
Read more
 2 in stock $147.94
Cat: 671598 Rel: 29 Nov 17 • View all Synth modules
 
Monophonic MIDI/USB interface Eurorack module with outputs for gate, clock, reset & two outputs for CV's
Notes: A-190-4 is the replacement for module A-190-1 which is no longer available. The functions of A-190-1 and A-190-4 are nearly the same (Midi In, Midi Out, CV1, CV2, Gate, Clock, Reset). But the operation of the A-190-4 has been improved because a 3-digit LED display is available. The current values of all parameters (like Midi channel, reference note, clock divider) can be read back and modified by means of up/down buttons. In addition, A-190-4 is equipped with an USB interface and the external +5V supply is no longer available. Consequently, the additional charges for the 5V adapter fall away.

The module width is the same for A-190-1 and A-190-4. In the A-100 basic systems the A-190-1 will be replaced by the A-190-4 from about May 2014.

Important notes:

- The Scale (SCA) and Tune (TUn) parameters remain unchanged when the module is initialized! Otherwise the initialization would overwrite the adjusted values. Because of the tolerances of electrical parts there are no fixed values for SCA and TUn which are valid for all modules. The values for SCA and TUn differ a bit from module to module because of the tolerances of electrical parts. In case that the module has been adjusted totally wrong: typical values are 100 for SCA (coarse) and 55 for TUn (coarse).

- The module comes with installed bus jumpers for CV and Gate. One has to remove the jumpers if e.g. an A-164, A-190-1, A-190-2, A-190-3, A-185-1 or A-185-2 is already connected to the CV and/or gate lines of the same bus board! If the A-190-3 should be used as CV and gate source for the A-100 bus the CV and gate connections of other CV/gate sources to the A-100 bus have to be removed. Otherwise short circuits are made between the outputs of the CV or gate transmitters!

- The gate level of the A-190-3 can be changed from +5V to +12V. For this the jumper on JP10A (behind the CV Note socket, labelled "GATE 5V JP10A") has to be removed and installed to JP10B (behind the 16 pin bus connector, labelled "GATE 12V JP10B").

- The module is a USB device or slave in USB mode. It has no USB host function (like computers or laptops with type A USB connectors).
Read more
 1 in stock $183.58
Cat: 671561 Rel: 18 Dec 17 • View all Synth modules
 
Pair of multicore signal connectors
Notes: A-180-9 is another simple but useful tool. It can be used to connect up to 14 signals between different cases by means of standard network cables (RJ45). These cables are available all over world smoothly in different lengths and colours. From the factory two black network cables with 0.5 m length are enclosed.

The upper network connector is wired to the eight sockets 1-8, the lower to the six sockets A-F. That way it's possible to pre-patch different cases and connect signals, that are required in all cases (e.g. clock, start/stop, master CV) by means of one or two cables only instead of 14 individual patch cables. When only eight signals are required only the upper network connector is required and the sockets 1-8 are used. When more than eight signals have to be patched both network connectors have to be used. It's also possible to wire the upper and lower network to different cases (i.e. signals 1-8 to external case #1 and signals A-F to external case#2).

The module is fully passive (no power supply required) and simply wires the 14 sockets to 14 pins of the network connectors.

The A-180-9 comes in pairs for combining two modular systems.
Read more
 9 in stock $107.98
Cat: 676696 Rel: 01 Feb 18 • View all Synth modules
 
Four-fold envelope follower with adjustable attack & release time for each channel
Notes: The A-135-4C is composed of four envelope followers with adjustable attack and release. The circuit was designed to be used as an addition for the A-135-4A/B Performance Mixer, adding ducking, compressor and expander functions to the mixing system. However, thanks to a full set of inputs and outputs, it is also possible to employ the A-135-4C for other tasks.

The A-135-4C offers four identical envelope followers. Each modulator comes equipped with an audio input, attack and release potentiometers as well as a CV output. LED's visualize control voltages generated by the module. The A-135-4C can be connected to the A-135-4A/B Performance Mixer via a Ribbon cable. Users are able to determine whether audio material gets tapped off directly after the input connectors, behind the gain stages or after the level control of the A-135-4A. By plugging in patch cables into the envelope follower's inputs, the internal routing can be suspended.
Read more
 1 in stock $107.98
Cat: 682313 Rel: 26 Mar 18 • View all Synth modules
 
Vactrol-based multimode filter based on a schematic by Nyle Steiner, featuring separate inputs for lowpass, bandpass & highpass
Notes: This filter's unique feature is that different filter types are realized by injecting the audio signal at different points of the circuit. For this reason, the A-101-1 has three inputs with level control: one lowpass input which is normalized to the bandpass input, which itself is normalized to the highpass input. The level controls make it possible to mix the filters and to generate new filter types. e.g. with all three filter levels turned to maximum level you get a notch filter.

Furthermore, the cutoff frequency influences which filter type is "monitored". This way you can blend from LP over BP to HP with increasing cutoff, known as "frequency scanning". Interesting effects happen when three different audio signals are used because they are both morphed and filtered at the same time.

Vintage edition with black faceplate and custom knobs.
Read more
 1 in stock $128.51
Cat: 676098 Rel: 04 Apr 18 • View all Synthesisers
 
Fully analogue, monophonic stand-alone synthesiser with USB & MIDI interface
Notes: The Dark Energy III is a monophonic stand-alone synthesizer with USB and MIDI interface. The sound generation and all modulation sources are 100% analog, only the USB/MIDI interface contains digital components. It is built into a rugged black metal case with wooden side plates. High quality potentiometers with metal shafts are used and each potentiometer is fixed to the case (no wobbly shafts and knobs). The distance between the controls is wider compared to A-100 modules, and knobs with vintage look are used.

Doepfer say that the main differences between II and III are an improved VCO (no warm-up period, additional triangle waveform, wider frequency range), resettable LFOs, improved ADSR and a lot of internal access points for DIYers.
Read more
 1 in stock $429.80
Cat: 684460 Rel: 23 Apr 18 • View all Synth modules
 
Two independent voltage controlled switches in one module - 4HP
Notes: Module A-150 (Dual VCS) contains two separate voltage-controlled switches.

Each switch has a control voltage input, a common Out / Input, and two In / Outputs. The switches are bi-directional: they can work in both directions, so can connect one input to either of two outputs, or either of two inputs to one output. Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Two LEDs show which in / output is active (i.e. which is connected to the common out / input).
Read more
 1 in stock $60.46
Cat: 682321 Rel: 30 Apr 18 • View all Synth modules
 
Complex 12-stage phase shifter with separate in- and outputs for all phaser stages
Notes: Module A-101-3 is a 12-stage phase shifter with vactrols as phase shifting elements. Vactrols are known for their smooth sound behaviour. In contrast to other phaser designs, the A-101-3 is much more flexible and offering a lot of new features not available from other phasers on the market. The main difference is that the Doepfer design offers access to each of the 12 input and output stages leading to a lot of new filters that cannot be obtained in other ways. Especially the free patchable feedback loops (yes, not only one feedback loop is possible) between each of the 12 stages, the separate phase shift control for the stages 1-6 and 7-12, and the 2 polarizers intended to control the feedback loops lead to completely new filter types (a polarizer is a circuit that is able to generate positive and negative amplifications in the range -1...0...+1 with -1 = inversion, 0 = full attenuation, +1 = unchanged signal, for details concerning the polarizer function please look at the A-133 VC Polarizer or A-138c Polarizing Mixer module).

Internally, the module is made of 2 independent 6 stage phase shifters (1-6 reps. 7-12) with separate audio inputs (with attenuators), audio outputs (with mix control), and phase shift control units. The phase shift control units feature both manual and voltage-controlled phase shifting (e.g. from a LFO, ADSR, Random Voltage, Theremin CV, Foot Controller CV ...). For each sub-module a phase shift display (LED) is available. The LED shows the illumination state of the 6 vactrols of the sub-module in question as it is connected in series with the internal vactrol LEDs.

Each of the 12 phase shift states is equipped with an audio output socket and feedback input socket to obtain full flexibility to create a multitude of different filters. The audio input signal and the output signals of stage 6 resp. stage 12 are mixed with 2 manual controls to obtain effects at two audio outputs (for normal phase shifting effect this is 50% input signal and 50% phase shifted signal). The two submodules are internally connected via normalized sockets so that two 6 stage phase shifters can be obtained without external patches. Audio output of stage 6 is normalized to audio input of stage 7 and CV input 1-6 is normalized to CV input 7-12. But due to the open structure of the module even other stages than stage 6 and stage 12 can be used as outputs to generate different sounds (simply patch the desired stage output to the normalized mix input socket).
Read more
 2 in stock $267.81
Cat: 684443 Rel: 30 Apr 18 • View all Synth modules
 
Four-channel stereo mixer - 8HP
Notes: A-138s is a simple but useful 4-in-2 mixing tool. It has four inputs available. Each input is equipped with an attenuator (Level) and a panning control that is used to distribute the signal to the left and right output. Beyond stereo mixing it is equally suited to create variable parallel routings. For example: Any of the four inputs may be routed in variable intensity to feed two filters.

You may regard the A-138s as a smaller version of the A-138m Matrix Mixer.

Inputs and outputs are DC coupled, i.e. the module can be used for the mixing of control signals too.

- 3U Eurorack module, 8 HP wide, 30 mm in depth
- Power consumption: 10 mA at +12 V and 10 mA at -12 V
Read more
 4 in stock $84.22
Cat: 684462 Rel: 22 May 18 • View all Synth modules
 
Electronic switch with up to four steps - 4HP
Notes: Module A-151 (Quad Sequential Switch) is like an electronic four-position rotary switch.

It includes trigger and reset inputs, four in/outputs, and a common out/input. Each time a pulse is received at the trigger input socket, the common out/input is connected to the next in/output. After the fourth in/output, the next trigger makes it step back to the first again, and so on. A positive pulse at the reset input switches the out/input immediately back to the first in/output. Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Four LED's indicate the active in/output (ie. the one that is connected to the out/input at any particular time).
Read more
 4 in stock $60.46
Cat: 692512 Rel: 18 Jun 18 • View all Synth modules
 
Basic voltage-controlled oscillator for the A-100 modular system
Notes: Module A-110-2 is a low-cost voltage-controlled oscillator. It's a slightly reduced version of the standard VCO A-110-1. Compared to the A-110-1, the A-110-2 has no sine output and the (expensive) octave rotary switch is replaced by a 3-position toggle switch. In return, the A-110-2 is equipped with an additional linear FM input and a soft sync input. A jumper is used to select the range of the tune control between about 1/2 octave and about 4 octaves. The width of the module is only 8 HP compared to the 10 HP of the A-110-1.

All other features are essentially the same as for the A-110-1.

Explanation of the jumpers and trimming potentiometers:

- JP2: CV connection to A-100 bus
- JP3: range of Tune control (installed = about 4 octaves, not installed = about 1/2 octave)
- JP4: AC/DC coupling of the linear FM input (installed = DC coupling, not installed = AC coupling)
- P5: 1V/Oct scale
- P6: frequency offset
- P7: high-end trim
- P8: adjustment +1 Oct. range switch
- P9: adjustment -1 Oct. range switch
- P10: temperature VCO heater

The core of the A-110-2 is - like the A-110-1 - a sawtooth oscillator (in contrast to the A-111-1, which is based on a triangle oscillator). The other waveforms are derived from the sawtooth by waveform converters. As the sawtooth reset (i.e. the back-to-zero slope) is not infinitely fast but takes a little bit of time the triangle is not perfect! At the bottom of the waveform it has a small glitch or notch that is caused by the sawtooth reset and cannot be eliminated by the waveform converter. If a perfect triangle is required, the A-111-1 is recommended.

The sawtooth output of the A-110-21 has a falling (or negative) slope. The front panel shows erroneously a rising (or positive) slope. This has no influence on the sound but becomes important when the module is used as an LFO or is mixed with the sawtooth output of another VCO.

The control voltage applied to the socket 1V/Oct is added to the control voltage coming from the bus (interruptible by removing the jumper JP2). Connecting a cable to the socket 1V/Oct does not interrupt the bus CV connection!
Read more
 2 in stock $123.10
Cat: 692516 Rel: 18 Jun 18 • View all Synth modules
 
Thru-zero quadrature VCO with Sine/Cosine core - special edition
Notes: This analogue VCO is well versed in the art of deep and beautiful thru-zero frequency modulation, allowing the frequency to stop when CVs with 0V are applied, and even to go backwards when modulated with negative CVs.

The term "quadrature" refers to simultaneously available sine and cosine waves at individual outputs. The VCO is sine based i.e. no waveshaping is used to derive the sine; for that reason, the sound is really clear and shows a minimum of distortion and overtones.

The module has two control sections:

The exponential section consists of the XTune control, the 1V/Oct input and the XFM input with the corresponding attenuator XFM.

The exponential control voltage is the sum of these three voltages. The linear section consists of the LTune control and the LFM input with the corresponding attenuator LFM. The linear control voltage is the sum of these two voltages.

The main advantage of the A-110-4 compared to other Thru Zero VCOs is that the design uses a sine/cosine core. The sine/cosine waves are not derived from other waveforms (e.g. sawtooth or triangle) by means of waveshaping. Rather the sine and cosine waves are the core of the VCO which results in very pure waves with a minimum of distortion and overtones.

With it's both control possibilities, linear and exponential, as well as it's thru-zero ability, the VCO is perfectly suited for all types of FM applications.
Read more
 2 in stock $140.38
Cat: 692504 Rel: 18 Jun 18 • View all Synth modules
 
18dB low pass filter based on a modified Moog cascade - 8HP
Notes: Module A-103 is a voltage controlled low pass filter with 18dB/octave slope. The circuit is based on a modified transistor ladder (Moog ladder) and is a reproduction of the legendary TB303 filter.

As for the rest the A-103 is identical to the A-120 Moog low pass filter (same controls, inputs/outputs) only the filter sound is different.
Read more
 2 in stock $80.98
Cat: 692503 Rel: 18 Jun 18 • View all Synth modules
 
Reproduction of the legendary British diode lowpass filter - 8HP
Notes: Module A-102 is a reproduction of the legendary low pass filter design that uses diodes in the filter stage as frequency controlling elements - resulting in "strange" resonance behaviour and frequency response, as resonance and frequency are not independent from another.

As for the rest, the A-102 is identical to the A-120 Moog low pass filter, the A-103 (18dB TB303 Filter) i.e. the same controls, inputs and outputs. Only the filter sound is different:

- Manual control of filter frequency
- 3 CV inputs (CV1, CV2, CV3), 2 of them with attenuator (CV2, CV3)
- Input level control
- Resonance control up to self-oscillation (depends upon the frequency setting for the A-102)
Read more
 1 in stock $79.90
Cat: 753440 Rel: 19 Jun 18 • View all Synth modules
 
B-STOCK: Item refurbished, repaired and in perfect working order.
Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


Module A-106-6 is a multimode filter that is based on the filter circuit of the Oberheim Xpander. The module features 15 different filter types (those filters of the A-107 that were available in the Xpander) with 8 filters available simultaneously. The toggle switch Filter Group is used to switch between 2 filter groups.

These filter types are available:

- 1L (6 dB low pass)
- 2L (12 dB low pass)
- 3L (18 dB low pass)
- 4L (24 dB low pass)
- 1H (6 dB high pass)
- 2H (12 dB high pass)
- 3H (18 dB high pass)
- 2B (6 dB band pass)
- 4B (12 dB bandpass)
- 2N (notch)
- 3A (allpass)
- 2H1L (asymmetrical band pass made of a 12 dB high pass and a 6 dB low pass)
- 3H1L (asymmetrical band pass made of a 18 dB high pass and a 6 dB low pass)
- 2N1L (combination of notch and 6 dB low pass)
- 3A1L (combination of allpass and 6 dB low pass)

The module features voltage-controlled resonance. For filter group 2 (2L, 4L, 2B ...) even self-oscillation is possible.

All standard VCF controls are available: manual filter frequency control Frq, one control voltage input with attenuator (FCV2) and one without attenuator (FCV1, ~ 1 V/octave). In addition, voltage-controlled resonance with manual control (Q) and a CV input with attenuator (QCV) are available.

The circuit is based on a 24dB lowpass filter. The outputs of the four internal filter stages (i.e. the 6, 12, 18 and 24dB outputs) are mixed together with different levels and polarities to obtain 15 different filters. Because of this special circuit the outputs have slightly different levels and noise floor. This is caused by the different internal amplifications and numbers of stages that are required to generate the filter in question. If e.g. a filter is derived by one stage only (e.g. the 6 dB, 12dB, 18dB and 24dB low pass) the noise floor is smaller compared to a filter that is derived by a combination of all four filter stages.
Read more
 1 in stock $132.66
Cat: 692508 Rel: 19 Jun 18 • View all Synth modules
 
Multimode filter based on the filter circuit of the Oberheim Xpander - 12HP
Notes: Module A-106-6 is a multimode filter that is based on the filter circuit of the Oberheim Xpander. The module features 15 different filter types (those filters of the A-107 that were available in the Xpander) with 8 filters available simultaneously. The toggle switch Filter Group is used to switch between 2 filter groups.

These filter types are available:

- 1L (6 dB low pass)
- 2L (12 dB low pass)
- 3L (18 dB low pass)
- 4L (24 dB low pass)
- 1H (6 dB high pass)
- 2H (12 dB high pass)
- 3H (18 dB high pass)
- 2B (6 dB band pass)
- 4B (12 dB bandpass)
- 2N (notch)
- 3A (allpass)
- 2H1L (asymmetrical band pass made of a 12 dB high pass and a 6 dB low pass)
- 3H1L (asymmetrical band pass made of a 18 dB high pass and a 6 dB low pass)
- 2N1L (combination of notch and 6 dB low pass)
- 3A1L (combination of allpass and 6 dB low pass)

The module features voltage-controlled resonance. For filter group 2 (2L, 4L, 2B ...) even self-oscillation is possible.

All standard VCF controls are available: manual filter frequency control Frq, one control voltage input with attenuator (FCV2) and one without attenuator (FCV1, ~ 1 V/octave). In addition, voltage-controlled resonance with manual control (Q) and a CV input with attenuator (QCV) are available.

The circuit is based on a 24dB lowpass filter. The outputs of the four internal filter stages (i.e. the 6, 12, 18 and 24dB outputs) are mixed together with different levels and polarities to obtain 15 different filters. Because of this special circuit the outputs have slightly different levels and noise floor. This is caused by the different internal amplifications and numbers of stages that are required to generate the filter in question. If e.g. a filter is derived by one stage only (e.g. the 6 dB, 12dB, 18dB and 24dB low pass) the noise floor is smaller compared to a filter that is derived by a combination of all four filter stages.
Read more
 2 in stock $139.30
Cat: 692510 Rel: 19 Jun 18 • View all Synth modules
 
Classic Moog voltage-controlled lowpass filter - 12HP
Notes: Module A-108 is a completely new voltage-controlled low pass filter based on the well-known transistor ladder (Moog ladder). The module has internally an 8-stage low pass filter with different slopes available: 6, 12, 18, 24, 30, 36, 42 and 48 dB per octave. In addition, it features a band pass output (i.e. band pass with transistor ladder). In the factory, the 4 low pass outputs of the A-108 are internally connected to the filter stages 6, 12, 24 and 48dB.

Resonance (Emphasis or Q) can be adjusted manually right up to self-oscillation, in which case the filter will behave like a sine wave oscillator. The A-108 features an external feedback input that enables the insertion of additional modules into the feedback path (e.g. VCA for voltage-controlled resonance or phaser/frequency shifter for phase/frequency shifting effects). The socket is normalized and internally connected to the 48dB low pass output if no cable is inserted into the feedback socket.

The frequency can be adjusted manually, or by voltage control. Three CV inputs (CV1, CV2, CV3) are available. CV2 and CV3 are equipped with attenuators.

The filter audio input is very sensitive so that distortion - if desired - is possible even with normal A-100 levels (e.g. VCO output). Self-oscillation will break off at high distortion levels as the internal feedback signal is drown out by the distorted audio signal. This feature may intentionally be used to create new sounds.

In combination with the Voltage Controlled Mixer A-135 and the Morphing Controller A-144 a filter with voltage-controlled slope can be realized (i.e. controlling the slope from 6dB to 48dB via CV).
Read more
 1 in stock $141.46
Cat: 692518 Rel: 18 Jun 18 • View all Synth modules
 
Analog VCO/LFO module with wide frequency range - 4HP
Notes: The Micro Precision VCO is a space-saving and utterly precise analog VCO/LFO with a extremely wide frequency range, immaculate tracking over at least ten octaves and nearly perfect waveforms.

Basically, it's the same circuitry like the High-End VCO A-111-2 but with reduced functions and controls. It is suitable as a modulator for exact linear FM and much more.

The A-111-3 has two elements for setting the frequency: A switch selecting between LFO and VCO mode as well as a tune control with a jumper-selectable range:

- Jumper position 1: 16Hz to 20 kHz
- Jumper position 2: 16Hz to 70Hz
- Without jumper: 16Hz to 22Hz

The XM potentiometer can be used as a fine tune control as long as nothing is patched to the XM socket.

The oscillator has a frequency range of at least fifteen osctaves (0.0001 - 40 Hz in LFO mode; 0.5 Hz to 20 kHz in VCO mode) and offers perfect 1 V per octave tracking over ten octaves minimum, typically in the range of 20 Hz to 20 kHz. Frequencies below 25 Hz are visualized with a two-colour LED.

The 1V per octave input is accompanied by two FM inputs, one for linear and one for exponential frequency modulation. A jumper determines whether the module obtains pitch CV via the internal bus.

The VCO has a triangle core from which sawtooth, pulse and triangle are derived. The wave forms are almost perfect and sans glitches.

The pulse width can be set with a control from 0 to 100% and of course it can be modulated.

There is one input for oscillator synchronisation and its type, either hard or soft sync, is jumper-selected. Both types differ in sound with the hard sync being more aggressive and richer in harmonics.
Read more
 1 in stock $147.94
Cat: 676693 Rel: 18 Jul 18 • View all Synth modules
 
Quad voltage controlled envelope generator - 8HP
Notes: A-141-4 is a quad voltage controlled Envelope generator and is primarily planned for polyphonic applications. The module contains four ADSR type voltage controlled envelope generators with common manual controls and CV inputs with polarizers for the all parameters Attack (A), Decay (D), Sustain (S) and Release (R). Each of the four envelope generators has available a gate input, a control LED and an envelope output.

The module has these controls and in/outputs are available:

- Attack (manual control)
- Decay (manual control)
- Sustain (manual control)
- Release (manual control)
- CVA control (polarizer for Attack CV input)
- CVD control (polarizer for Decay CV input)
- CVS control (polarizer for Sustain CV input)
- CVR control (polarizer for Release CV input)
- CVA socket (Attack CV input)
- CVD socket (Decay CV input)
- CVS socket (Sustain CV input)
- CVR socket (Release CV input)
- Gate inputs 1 - 4
- Envelope outputs 1 - 4
- LED displays 1- 4 (envelope display)

The output voltage range for each envelope is 0 - 10V.
Read more
 3 in stock $149.02
Cat: 684450 Rel: 18 Jul 18 • View all Synth modules
 
Dual ADSR envelope generator - 8HP
Notes: Module A-140-2 contains two ADSR type envelope generators behind a front panel with 8 HP only.

Each ADSR provides these controls and in/outputs:

- LED (displays the envelope output)
- A: manual Attack control
- D: manual Decay control
- S: manual Sustain control
- R: manual Release control
- Gate Input
- Retrigger Input
- CVT Input with attenuator (CVT = CV Time)
- Envelope Output 1
- Envelope Output 2

The output voltage range for each envelope is 0 - 10V. The time range of Attack/Decay/Release is about 1ms to 30s.

By means of internal jumpers one can select which time parameters are controlled by the CVT input (e.g. D only or D+R or A+D+R) and in which direction (i.e. if an increasing CVT shortens or stretches the time parameter in question).

Socket CVT can be normalled to an internal fixed voltage (i.e. the switching contact is connected to an internal fixed voltage). That way it's possible to change all time parameters simultaneously by means of the CVT control.

Another jumper is used to set output 2 to normal or inverted envelope.

And another jumper is used for the normalling of Gate 2 to Gate 1 (i.e. ADSR#2 is also triggered by Gate 1).

Two more jumpers are used for the optional bus access to the gate signal of the bus for each ADSR. Changing the positions of the mentioned jumpers allows to modify the factory settings.
Read more
 1 in stock $129.58
Cat: 676692 Rel: 18 Jul 18 • View all Synth modules
 
Octal VCA module containing four VCA pairs - 8HP
Notes: A-132-8 is an octal VCA and primarily planned for polyphonic applications. The module contains four VCA pairs. Each pair includes two daisy-chained VCAs. One VCA has a linear control scale, for the second VCA linear or exponential control scale can be chosen by means of jumpers. We decided to provide two VCAs for each voice because usually one VCA is required for loudness envelope and a second one for velocity (or other functions like individual voltage-controlled loudness of each voice, amplitude modulation and so on).

These controls and in/outputs are available:

- Default Gain 1 (GL)
- Default Gain 2 (GX)
- CV Input VCA 1
- CV Input VCA 2
- Audio Input
- Audio Output

In addition, an Audio Sum Output is also available.

The module features two Default Gain controls (GL, GX), that enable the opening of the first VCAs (L) and/or second VCAs (X). For this the controls GL and GX generate two internal control voltages 0...+10V which are connected to the switching contacts of the sockets 1L...4L (control GL) and 1X...4X (control GX). As long as no patch cable is inserted into the socket in question the internal default control voltage (GL or GX) is used to control the corresponding VCA. This is necessary when the VCA in question is not in use (i.e. no external CV available). Otherwise the VCA would close and there would be no output signal even if the other VCA in the chain is open. The controls GL and GX are also useful for testing polyphonic patches (e.g. for tuning the VCOs).

In the factory the CV inputs are adjusted for a CV range 0...+10V - matching to the polyphonic ADSR module A-141-4. But the sensitivity of each CV input can be adjusted by means of a trimming potentiometer to adapt the CVs even to other control voltage ranges.
Read more
 2 in stock $151.18
Cat: 577766 Rel: 15 Aug 18 • View all Synth modules
 
Analogue noise & random module - 8HP
Notes: Module A-118 is a noise and random voltage generator. It produces three types of signal: white noise, coloured noise, and random voltage.

White and coloured noise can be used as audio sources, and also, in conjunction with a sample & hold module, as control voltages, and the random voltage is a useful source of voltage control, especially for its low frequency content.

The A-118 gives you the ability to mix the relative amounts of Red (low frequency component) and Blue noise (high frequency component) in the coloured noise output.

There are knobs to control the rate of change and amplitude of the random voltage, and two LEDs indicate the state of the voltage at any one time.
Read more
 2 in stock $63.70
Cat: 577748 Rel: 15 Aug 18 • View all Synth modules
 
Reverb effects module with spring reverb tank - 8HP
Notes: Module A-199 is a spring reverb module. The reverb effect is electronically simulated by means of 3 spiral springs. Spring reverb systems have a very characteristic sound that is based on the (insufficient) mechanical properties of the springs like signal delays, audio resonances, limited frequency range, acoustic feedback behaviour, sensitivity to mechanical shocks and others.

The 3-spring system used in the A-199 ensures a "dense" reverb because of the different properties of the three springs.

The A-199 implies some special features that are not self-evident for spring reverb units:

The reverb signal can be fed back to the input using the Feedback control. Even self-oscillation of the springs similar to the self-oscillation of filters is available. The feedback loop can lead even via external modules like VCA, VCF, phaser, frequency shifter, vocoder, distortion/waveshaper, ring modulator and others. In this case the reverb output of the A-199 is connected to the input of the external module(s) and the output of the external module(s) is fed back to the Ext. Feedback In socket of the A-199. This socket contains a switch that interrupts the internal feedback loop as soon as a plug is inserted.

Another feature is the Emphasis control. This enables the adjustment of the accentuation of middle frequencies (around ~ 2kHz).

With the Mix control the relation between original and reverb signal appearing at the mix output is adjusted.

Using all these features very extreme and unusual effects can be generated with the A-199.
Read more
 2 in stock $118.17
Cat: 698542 Rel: 14 Aug 18 • View all Synth modules
 
Sound source deriving four subharmonics from an incoming square wave signal - 26HP
Notes: Module A-113 is a new sound source that derives four so-called subharmonics (German: Subharmonische) from an incoming pulse signal. The term subharmonics was introduced by Oskar Sala in connection with his so-called Mixtur-Trautonium. A subharmonic means in this context a sawtooth wave (German: Kippschwinger) whose frequency is derived from a master frequency and the master frequency is an integer multiple in the range of 1...24 of the subharmonic - in other words: the master frequency is divided by an integer 1...24 to obtain the subharmonic.

The output waveform of a subharmonic is sawtooth (as also used in the original Trautonium) and not sine. The term subharmonics is somewhat misleading. The master frequency comes e.g. from an A-110 or A-111 to the frequency input of the A-113. The frequency dividers of the 4 subharmonics is adjusted with up/down buttons as displayed with two character LED displays. The subharmonics are available as single outputs and as mix output with adjustable levels for the subharmonics.

Two gate type control inputs enable to select between 4 different mixtures, i.e. 4 different settings of the frequency dividers. In the original Trautonium these are controlled by foot switches to switch between 3 mixtures while playing (the original Trautonium has only 3 mixtures available but with the 2 gate inputs of the A-113 four different settings can be addressed).

Additionally, the A-113 features a mixture memory with 50 presets. Each preset consists of 4 mixtures that can be selected with the gate inputs, each mixture contains the values of the 4 frequency dividers.
Read more
 1 in stock $237.57
Cat: 698547 Rel: 15 Aug 18 • View all Synth modules
 
Voltage controlled waveform processor - 8HP
Notes: Module A-116 provides voltage-controlled dynamic waveform modification of audio signals. It can produce new waveforms from the standard VCO shapes, and modulate these changes in real time. The signal first of all goes through an input amplifier, which can attenuate the signal as well as amplify it by up to a factor of 2.

After the input amplifier, the signal goes through two parallel processors: a clipping circuit, and an asymmetrical amplifier. The processed signals are added together and sent to the output.

Clipping-Level and Symmetry amounts are not just manually controllable, but can also be modulated by control voltages, to produce complex, constantly changing waveforms.
Read more
 1 in stock $71.26
Cat: 698465 Rel: 15 Aug 18 • View all Synth modules
 
Reverb effects module with spring reverb tank - 8HP
Notes: Module A-199 is a spring reverb module. The reverb effect is electronically simulated by means of 3 spiral springs. Spring reverb systems have a very characteristic sound that is based on the (insufficient) mechanical properties of the springs like signal delays, audio resonances, limited frequency range, acoustic feedback behaviour, sensitivity to mechanical shocks and others.

The 3-spring system used in the A-199 ensures a "dense" reverb because of the different properties of the three springs.

The A-199 implies some special features that are not self-evident for spring reverb units:

The reverb signal can be fed back to the input using the Feedback control. Even self-oscillation of the springs similar to the self-oscillation of filters is available. The feedback loop can lead even via external modules like VCA, VCF, phaser, frequency shifter, vocoder, distortion/waveshaper, ring modulator and others. In this case the reverb output of the A-199 is connected to the input of the external module(s) and the output of the external module(s) is fed back to the Ext. Feedback In socket of the A-199. This socket contains a switch that interrupts the internal feedback loop as soon as a plug is inserted.

Another feature is the Emphasis control. This enables the adjustment of the accentuation of middle frequencies (around ~ 2kHz).

With the Mix control the relation between original and reverb signal appearing at the mix output is adjusted.

Using all these features very extreme and unusual effects can be generated with the A-199.
Read more
 1 in stock $131.74
Cat: 684451 Rel: 28 Aug 18 • View all Synth modules
 
Dual envelope controlled VCA - 8HP
Notes: Module A-142-2 contains two envelope-controlled VCAs behind a front panel with 8 HP only. Each of the two sub-units is the combination of a simple AD/ADSR/AR envelope generator and a VCA. The type of envelope can be selected by means of a toggle switch:

- AD: Attack-Decay
- AR: Attack-Release
- ADSR: Attack-Decay-Sustain-Release with the limitation that Decay Time = Release Time and fixed Sustain level (factory setting 50%)

Each sub-unit provides these controls and in/outputs:

- LED control (envelope display)
- Attack (A), manual control
- Decay/Release (D/R), manual control
- Mode switch (AD, AR, ADSR)
- Audio level control (small control without knob)
- CVT Input (CVT = CV Time)
- CV Ducking input
- Attenuator for CVT (small control without knob)
- Gate Input
- Manual Gate (momentary switch)
- Audio Input
- Audio Output

The Envelope Output of version 1 has been cancelled for the benefit of the new CV Duck input. But there is an internal pin header available that has available the envelope signal (0...+10V) and the CV input of the VCA (0...+10V). Ex works the pins are shortened by a jumper but can be used for modifications (envelope output, VCA CV input).

By means of two internal jumpers for each sub-unit one can select which parameter(s) are controlled by the CVT input (e.g. D+R only or A only or A+D+R) and in which direction (i.e. if an increasing CVT shortens or stretches the time parameter in question). Two more jumpers are used for the optional bus access to the gate signal of the bus for each envelope.

CV Duck is an additional control input for the VCA that can be used to mute the VCA by means of an external control voltage. Beyond about +5V CV Duck the VCA is fully muted, in the range 0...+5V there is only a partial muting. Circuitry-wise the CV Duck signal is amplified by two, inverted and added to the internal envelope signal (0...+10V). The sum of both signals is used to control the VCA.

The time range of Attack/Decay/Release is about 1ms to 30s (can be modified by changing the value of a capacitor).

Applications:

Virtually in each patch one or more envelope/VCA combos together with a sound source are very useful, mainly for percussive sounds. Voltage control of the times and the ducking animates each performance.
Read more
 1 in stock $140.38
Cat: 676691 Rel: 21 Sep 18 • View all Synth modules
 
Polyphonic filter with four identical 24dB Lowpass filters 8HP
Notes: A-105-4 is our first polyphonic filter and contains four
identical 24dB Lowpass filters (SSM2044 type). It has
available common manual controls and CV inputs with
attenuators for these parameters:

Frequency (F)

Frequency Modulation Intensity (FM)

Resonance (Q)

Audio Input Level (L)
Each filter has available a separate FM input as well as an Audio Input and Output. The FM input is typically connected to the output of the associated envelope generator (e.g. A-141-4).
The envelope amount for all four filters is controlled by the FM knob and the CVFM input by means of four built-in VCAs, which are controlled by the FM control and CVFM input. This allows also voltage control of the envelope amounts.

In addition common frequency modulation for all filters is possible (e.g. by an LFO). For this the CVF input with attenuator can be used. The range of the audio input level control (L) allows also clipping/distortion with typical A-100 audio levels
(e.g. from A-111-4) at the filter inputs. Even this parameter is voltage controllable as well as the resonance (Q).
Application: polyphonic patches (four VCFs with same parameters).
Read more
 1 in stock $184.66
Cat: 703570 Rel: 05 Oct 18 • View all Synth modules
 
24dB low pass filter based on a Curtis filter circuit - 8HP
Notes: Module A-122 is a voltage-controlled low-pass filter, which filters out the higher parts of the sound spectrum, and lets lower frequencies pass through.

The cut-off frequency determines the point at which filtering takes effect. You can control this manually, or by voltage control (filter modulation, for instance by an LFO). Two CV inputs are available.

The cut-off slope is -24 dB/octave. The circuitry uses a Curtis chip, and is very similar to the classic Oberheim filter sound. Because of its different circuitry and controls, the A-122 has a considerably different sound to the A-120 'Moog-like' filter, especially in the way the resonance behaves.

Voltage controlled resonance: on the A-122, resonance can be controlled not just manually, but by voltages as well, right up to self-oscillation. In this case, the filter behaves like a sine wave oscillator.
Read more
 2 in stock $96.10
Cat: 744271 Rel: 05 Oct 18 • View all Synth modules
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


Module A-122 is a voltage-controlled low-pass filter, which filters out the higher parts of the sound spectrum, and lets lower frequencies pass through.

The cut-off frequency determines the point at which filtering takes effect. You can control this manually, or by voltage control (filter modulation, for instance by an LFO). Two CV inputs are available.

The cut-off slope is -24 dB/octave. The circuitry uses a Curtis chip, and is very similar to the classic Oberheim filter sound. Because of its different circuitry and controls, the A-122 has a considerably different sound to the A-120 'Moog-like' filter, especially in the way the resonance behaves.

Voltage controlled resonance: on the A-122, resonance can be controlled not just manually, but by voltages as well, right up to self-oscillation. In this case, the filter behaves like a sine wave oscillator.
Read more
 1 in stock $92.48
Cat: 703564 Rel: 08 Oct 18 • View all Synth modules
 
Analogue noise/random with black faceplate & custom knobs - 8HP
Notes: Module A-118 is (as you might have guessed) a noise and random voltage generator. It produces three types of signal: white noise, coloured noise, and random voltage. The noise signal is generated 100% analogue by amplification of the noise of a transistor. White and coloured noise can be used as audio sources, and also, in conjunction with a sample & hold module, as control voltages, and the random voltage is a useful source of voltage control, especially for its low frequency content.

The A-118 gives you the ability to mix the relative amounts of Red (low frequency component) and Blue noise (high frequency component) in the coloured noise output.

There are knobs to control the rate of change and amplitude of the random voltage, and two LEDs indicate the state of the voltage at any one time.
Read more
 1 in stock $66.94
Cat: 703567 Rel: 08 Oct 18 • View all Synth modules
 
Voltage-controlled multi-mode filter - 8HP
Notes: Module A-121 is a voltage-controlled multi-mode filter with a cut-off slope of -12 dB / octave. Four simultaneous outputs are available, each with different characteristics: low-pass, band-pass, high-pass and notch (or band reject). The cut-off frequency determines the point at which the respective filter effects appear. The frequency can be adjusted manually, or by voltage control (Filter modulation, for instance by an LFO or ADSR). Two CV inputs are available, whose control voltages are summed. Resonance (Emphasis or Q) can be adjusted manually, or by voltage control, right up to self-oscillation, in which case it will behave like a sine wave oscillator.

Technical notes: Module A-121-2 is the successor of the obsolete module A-121. But the circuitry is totally different from the A-121 which used the obsolete CEM3320 filter circuit. The sound of the new module A-121-2 is identical to filter of the Dark Energy II but has been expanded by the voltage-controlled resonance feature.
Read more
 1 in stock $107.98
Cat: 707080 Rel: 23 Oct 18 • View all Synth modules
 
Breakout module for the A-127 Triple Resonance Filter - 8HP
Notes: This expansion module offers the following additional functions:

- Notch filter for each sub-unit
- Separate outputs for lowpass, high-pass, bandpass and notch for each sub-unit
- Separate audio input with attenuator for each sub-unit

The breakout module allows the separate use of each of the three A-127 filters. In addition, the filters can be patched parallel or serial. Especially the serial connection of three notches generates very complex phasing-like structures. For parallel filter connection the existing mixer of the main module may be used or an external mixer. For serial connection the filters are patched in the desired sequence at the breakout module. A jumper is used to define the filter type for each sub-unit for the mix unit of the main module.

The breakout module can be used without modification only in combination with the new version of the A-127 (PCB printing "Version 4"). Only the new version has the expansion connector available, that is required to connect the breakout module without soldering. It's also possible to combine the breakout module with older versions of the A-127 (versions 1, 2 and 3) but in this case soldering is required to connect the breakout module to the main module (soldering 4 wires to each filter unit).
Read more
 1 in stock $75.59
Cat: 707078 Rel: 23 Oct 18 • View all Synth modules
 
Classic voltage controlled phase shifter - 8HP
Notes: Module A-125 (VC Phaser) is a voltage controlled phase shifter. Phase shifting can be controlled either manually or by voltage control. Other parameters which can be controlled are resonance (governing the depth of the comb filtering, and tonal colour) and mix (the amount of the original signal which is added to the phase-shifted signal). The A-125 is used to generate the typical phaser sound ("jet sound"). Due to the voltage control feature not only the usual LFO-controlled phasings but even ADSR-, random-, sequencer- or S&H-controlled phasings are possible. In combination with the Shepard generator A-191 and several A-125 never ending barberpole phasing effects come true.
Read more
 1 in stock $85.30
Cat: 684442 Rel: 30 Oct 18 • View all Synth modules
 
Voltage controlled highpass filter - 8HP
Notes: A-123-2 is a voltage controlled high-pass filter with four filter outputs (6, 12, 18 and 24dB slope). It also features voltage control of the resonance.

These controls and in/outputs are available:

- Audio In with attenuator (Lev)
- Manual Frequency control (Frq)
- FCV1: Frequency control input (~ 1V/oct)
- FCV2: Frequency control input with polarizer
- QCV: Resonance control input with attenuator
- Manual Resonance control (Q)
- 6dB Output
- 12dB Output
- 18dB Output
- 24dB Output
Read more
 1 in stock $96.11
Cat: 710942 Rel: 29 Nov 18 • View all Synth modules
 
Dual VCA with linear response - 4HP
Notes: Module A-132-1 (Dual Low Cost VCA) contains two voltage controlled amplifiers, with a linear response most suited to regulating the level of control voltages (ADSR amount, level of vibrato effect, etc).

In non-critical situations, though, its VCAs can be used to control audio signals.

Amplification is governed by the sum of the voltages patched into the two CV inputs.
Read more
 1 in stock $66.94
Items 1 to 50 of 142 on page 1 of 3
1  2  3  »

Filter

Saved Searches
Save current search
Release Date
Close