100% Secure Shopping

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Secure Shopping

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

View:
Options
Items 1 to 50 of 71 on page 1 of 2
1  2  »
Cat: 577792 Rel: 06 Jun 19 • View all Synth modules
 
Electronic switch with up to four steps - 4HP
Notes: Module A-151 (Quad Sequential Switch) is like an electronic four-position rotary switch.

It includes trigger and reset inputs, four in / outputs, and a common out / input. Each time a pulse is received at the trigger input socket, the common out / input is connected to the next in / output. After the fourth in / output, the next trigger makes it step back to the first again, and so on. A positive pulse at the reset input switches the out / input immediately back to the first in / output (see Fig. 1). Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Four LEDs indicate the active in / output (i.e. the on that is connected to the out / input at any particular time).
Read more
 3 in stock $60.46
Cat: 671576 Rel: 29 Nov 17 • View all Synth modules
 
Enhanced clock divider with multiple dividing factors - 4HP
Notes: Module A-160-2 is an enhanced version of the standard clock divider A-160. The module is a frequency divider for clock/trigger/gate signals, designed to be a source of lower frequencies, particularly for rhythm uses. The Clock input will take any digital signal from, eg. LFO, MIDI sync, or the gate from a MIDI-CV interface. At the outputs, you have access to three sets of seven different sub-divided clock signals, from half the clock frequency down to 1/128. The low/high levels of the output signals are 0V and about +10V.

The A-160-2 also has a reset input. Whenever a reset signal is sensed, all outputs are set to certain levels which depend upon the selected mode.

These are the most important features of the module:

Three different sets of dividing factors, selected by a three-position switch at the front panel:
- Power of two: 2, 4, 8, 16, 32, 64, 128
- Prime numbers: 2, 3, 5, 7, 11, 13, 17
- Integer: 2, 3, 4, 5, 6, 7, 8

Two output modes, selected by a two-position switch at the front panel:
- Gate mode: outputs act like the outputs of typical binary dividers
- Trigger mode: in this mode the outputs are AND-wired with the clock signal (i.e. the clock pulsewidth affects the pulsewidth of the outputs)
- Clock edge type selected by a jumper on the pc board:
- Positive: the rising edge of the clock signal triggers the state change of the outputs
- Negative: the falling edge of the clock signal triggers the state change of the outputs

Reset behaviour by two jumpers on the pc board:
- Level triggered: the level at the Reset input triggers the Reset
- Edge triggered: the edge of the signal at the Reset input triggers the Reset
- Positive: a high level (> 2.5V) or the rising edge at the Reset input triggers the Reset
- Negative: a low level (< 1 V) or the falling edge at the Reset input triggers the Reset

Output polarity selected by a jumper on the pc board:
- Positive: non-inverted outputs
- Negative: all seven outputs are inverted

Width: 4HP / 20mm
Depth: 35mm (Measured from the rear side of the front panel)
Current: +12V: +50mA, -12V: -0mA
Read more
 4 in stock $95.02
Cat: 731949 Rel: 10 Jun 19 • View all Synth modules
 
Quad low frequency oscillator - 4HP
Notes: Module A-145-4 is a simple quad LFO (Low Frequency Oscillator). Not a very "exciting" module, just a bread-and-butter device and a simple demon for work. Virtually in every modular system several LFOs are required for modulation purposes. The module contains four simple LFOs with the waveforms triangle and rectangle. A dual colour LED (red = positive / yellow = negative output voltage) indicates the triangle output of each LFO. The frequency range can be chosen for each LFO individually by means of a jumper between about 50 Hz ... 0.04 Hz (about 20 seconds, jumper removed) and about 2Hz ... 0.002 (about 8 minutes, jumper installed).

The module can be treated as a slimmed version of the quad LFO A-143-3 as it has similar features available. But the distances between the controls are smaller and rubberized small-sized knobs are used. In return the front panel has 4 HP only which is less than one third of the A-143-3. The module is primarily planned for applications where only limited space is available. The functional difference compared to the A-143-3 are the missing sawtooth outputs and frequency range switches.
Read more
 1 in stock $77.74
Cat: 671589 Rel: 29 Nov 17 • View all Synth modules
 
Four-channel stereo mixer - 8HP
Notes: A-138s is a simple but useful 4-in-2 mixing tool. It has four inputs available. Each input is equipped with an attenuator (Level) and a panning control that is used to distribute the signal to the left and right output. Beyond stereo mixing it is equally suited to create variable parallel routings. For example: Any of the four inputs may be routed in variable intensity to feed two filters.

You may regard the A-138s as a smaller version of the A-138m Matrix Mixer.

Inputs and outputs are DC coupled, i.e. the module can be used for the mixing of control signals too.

- 3U Eurorack module, 8 HP wide, 30 mm in depth
- Power consumption: 10 mA at +12 V and 10 mA at -12 V
Read more
 5 in stock $74.50
Cat: 684460 Rel: 23 Apr 18 • View all Synth modules
 
Two independent voltage controlled switches in one module - 4HP
Notes: Module A-150 (Dual VCS) contains two separate voltage-controlled switches.

Each switch has a control voltage input, a common Out / Input, and two In / Outputs. The switches are bi-directional: they can work in both directions, so can connect one input to either of two outputs, or either of two inputs to one output. Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Two LEDs show which in / output is active (i.e. which is connected to the common out / input).
Read more
 1 in stock $60.46
Cat: 671564 Rel: 29 Nov 17 • View all Synth modules
 
12dB multi-mode filter with unique classic circuitry, based on the filter from the 70s EDP Wasp synth
Notes: Module A-124 is a special 12dB multimode filter using the "strange" filter circuit of the "EDP Wasp" (an analog synthesizer with black/yellow case built end of the seventies, manufactured by the UK company "Electronic Dream Plant" with Chris Huggett und Adrian Wagner). This design "abuses" digital inverters as analog operational amplifiers leading to distortions and other "dirty" effects that generate the specific sound of this filter. The filter is equipped with a band pass output and a combined low/notch/high pass output. For this output a control knob defines the relation between low and high pass signal. If both signals appear at the same level (i.e. middle position of the Mix knob) one obtains a notch filter. Otherwise the low or high pass signal predominates. The module does not feature self-oscillation in contrast to most of the other filters of the A-100 system.

Inputs: Audio In, CV In (2x)
Outputs: Bandpass Out, Low/Highpass Mix-Out
Controls: Audio and CV attenuator, Frequency, Resonance, LP/HP Mix

The function and operation of this module is very similar to the module SEM VCF A-106-5. But the sound of both filters is very different! The only functional difference is the position of the sockets and controls, and the function of the controls CV2 (A-124: normal attenuator, A-106-5: polarizer).

- 3U Eurorack module, 8HP wide, 45mm deep
- Current draw 30mA
Read more
 8 in stock $83.10
Cat: 577762 Rel: 06 Jun 19 • View all Synth modules
 
4 channel mixer - 8HP
Notes: Module A-138 is a four channel mixer, which can be used with either control voltages or audio signals. Each of the four inputs has an attenuator, and there's a master attenuator, so that the mixer can be used at the end of the audio chain - i.e. it can be used to interface directly with an external mixer, amplifier, etc.

The A-138a version features potentiometers with linear response, so especially suitable for control voltage mixing.
Read more
 2 in stock $57.22
Cat: 731938 Rel: 10 Jun 19 • View all Synth modules
 
Noise/random generator - 4HP
Notes: Module A-118-2 is the slim version of module A-118-1 and offers essentially the same features as the A-118-1. But the distances between the controls are smaller and rubberized small-sized knobs are used. In return the front panel has 4 HP only which is half the width of the A-118-1. The module is primarily planned for applications where only limited space is available. The functional difference between A-118-1 and A-118-2 is the additional T&H/S&H unit which is not included in the A-118-1.

The module generates the signals white noise, coloured noise, continuous random voltage and stepped random voltage (derived from the continuous random voltage by means of a S&H/T&H unit).

The noise signal is generated 100% analogue by amplification of the noise of a transistor. White and coloured noise are usually used as audio sources. The random voltages are normally used as control voltages (e.g. for filter frequency or any other voltage controlled parameter).

The A-118-2 gives you the ability to mix the relative amounts of Red (low frequency component) and Blue noise (high frequency component) in the coloured noise output.

For the continuous random voltage the rate of change (Rate) and amplitude (Level) of the random voltage can be adjusted. The continuous random voltage is derived from the coloured noise signal by low pass filtering. Consequently the settings of the controls for the coloured noise (Blue, Red) affect the behaviour of the random voltage! A dual colour LED (red = positive / yellow = negative output voltage) indicates the continuous random voltage.

The continuous random voltage is used as source for the S&H/T&H unit. The type of operation can be set to S&H (sample and hold) or T&H (track and hold). When T&H is chosen the output signal follows the input signal (= continuous random voltage) as long as the Clock input is "high". As soon as the clock signal changes to "low" the last voltage is stored. When S&H is chosen the input signal (= continuous random voltage) is sampled at the rising edge of the Clock signal.

For the Clock signal a "digital" signal (e.g. Clock, Gate, rectangle output of an LFO) is required. It does not work with slowly changing continuous CV signals. Another dual colour LED (red = positive / yellow = negative output voltage) indicates the stepped random voltage.
Read more
 3 in stock $77.74
Cat: 731939 Rel: 11 Jun 19 • View all Synth modules
 
Voltage controlled 12dB/octave filter - 8HP
Notes: Module A-121-3 is functionally nearly identical to module A-121-2. Only the distances between the controls and sockets are smaller and rubberized, small rotary knobs are used. Therefore the front panel width is only 4HP compared to 8HP of the A-121-2. In the first place it is planned for applications where only limited space is available. The only functional difference compared to the A-121-2 is the missing attenuator for the resonance CV input CQ.

These are the most important features of the module:

- Voltage-controlled multi-mode filter with a cut-off slope of -12 dB / octave (identical to the filter of the Dark Energy II/III but has been expanded by the voltage controlled resonance feature)
- Four simultaneous outputs are available, each with different characteristics: low-pass (LP), high-pass (HP), band-pass (BP) and notch (N)
- Manual control Frequ. for the cut-off frequency of the filter (the cut-off frequency determines the point at which the respective filter effect appears)
- Two inputs for frequency control by means of external control voltages (frequency modulation, e.g. by ADSR or LFO):
- Control voltage input CV1 without attenuator, about 1V/octave sensitivity
- Control voltage input CV2 with attenuator FCV2 for the adjustment of the modulation depth of input CV2
- Frequency range about 10Hz ... 20kHz
- Manual control Q for the resonance of the filter
- Control voltage input CQ without attenuator for voltage control of the resonance
- Resonance up to self-oscillation, in which case the module will behave like a sine wave oscillator even without audio input signal
- Audio input In with attenuator Level for the adjustment of the filter input level (beyond about pos. 5 clipping/distortion occurs with typical A-100 audio levels)
Read more
 1 in stock $96.10
Cat: 577791 Rel: 10 Jul 19 • View all Synth modules
 
VCA with exponential response for low level sensitivity - 8HP
Notes: Module A-131 provides voltage-controlled amplification. For audio signals, you would normally use the exponential VCA (A-131), and for control voltages, the linear VCA (A-130). It doesn't always have to be that way, though.

The amount of amplification the VCA's provide is determined by the voltage at the CV input, and the position of the gain control, which sets the overall gain in the system.

The VCA has two audio inputs, each with an attenuator. They are amplified by an amount determined by the combination of the gain and the two CV controls.
Read more
 1 in stock $74.50
Cat: 684443 Rel: 30 Apr 18 • View all Synth modules
 
Four-channel stereo mixer - 8HP
Notes: A-138s is a simple but useful 4-in-2 mixing tool. It has four inputs available. Each input is equipped with an attenuator (Level) and a panning control that is used to distribute the signal to the left and right output. Beyond stereo mixing it is equally suited to create variable parallel routings. For example: Any of the four inputs may be routed in variable intensity to feed two filters.

You may regard the A-138s as a smaller version of the A-138m Matrix Mixer.

Inputs and outputs are DC coupled, i.e. the module can be used for the mixing of control signals too.

- 3U Eurorack module, 8 HP wide, 30 mm in depth
- Power consumption: 10 mA at +12 V and 10 mA at -12 V
Read more
 4 in stock $84.22
Cat: 745791 Rel: 10 Sep 19 • View all Synth modules
 
Simple & effective voltage-controlled frequency divider - 8HP
Notes: Module A-163 is a voltage controlled audio frequency divider. The frequency of the input signal (preferably the rectangle output of a VCO) is divided by an integer factor N (N = 1, 2, 3, 4 ... up to 32). N can be adjusted manually and modulated with an external control voltage (e.g. from LFO, ADSR, Random, MIDI-to-CV, Theremin, Light-to-CV, analogue sequencer) with attenuator. The control input has polarizing function, i.e. the manually adjusted dividing factor can be modulated upwards or downwards. The basic idea of a polarizer is described in the modules A-133 Voltage Controlled Polarizer and A-138c Polarizing Mixer.

The output waveform is rectangle with 50% duty cycle. Unlike the A-115 with fixed dividing factors (2, 4, 8, 16) the dividing factor of the A-163 is voltage controlled and can be any integer value between 1 and about 20 (but only one output). In contrast to A-113 the dividing factor of the A-163 is voltage controlled and the output waveform is rectangle (the A-113 has 4 sawtooth outputs with 4 adjustable but not voltage controlled dividers).
Read more
 1 in stock $77.75
Cat: 671592 Rel: 29 Nov 17 • View all Synth modules
 
12dB multi-mode filter based on classic SEM filter circuitry
Notes: Module A-106-5 is a 12dB multimode filter that is based on the filter circuit of the Oberheim SEM module. The filter is equipped with a band pass output and a combined low/notch/high pass output. For this output a control knob defines the relation between low and high pass signal. If both signals appear at the same level (i.e. middle position of the Mix knob) one obtains a notch filter. Otherwise the low or high pass signal predominates. The module does not feature self oscillation in contrast to most of the other filters of the A-100 system. The module generates a distorted audio signal if the level control is set to about 50% (i.e. centre position) or more with A-100 standard signals like VCOs.

Inputs: Audio In, CV1 In without attenuator, CV2 In with Polarizer
Outputs: Bandpass Out, Low/Highpass Mix-Out
Controls: Audio Attenuator, CV2 Polarizer, Frequency, Resonance, LP/HP Mix

The function and operation of this module is very similar to the Wasp filter module A-124. But the sound of both filters is very different! We will publish no separate user's manual for the A-106-5 but a combined manual for both A-106-5 and A-124. The only functional difference is the position of the sockets and controls, and the function of the controls CV2 (A-124: normal attenuator, A-106-5: polarizer)

Width: 8HP / 40.3mm
Depth: 55mm (Measured from the rear side of the front panel)
Current: +12V: +30mA, -12V: -20mA
Read more
 3 in stock $89.62
Cat: 577771 Rel: 29 Nov 17 • View all Synth modules
 
Envelope follower & pre-amplifier for microphone/line-signals - 8HP
Notes: Module A-119 (External Input / Envelope Follower) is designed to allow external audio signals to be integrated into the System A-100. It comprises a pre-amp, envelope follower, and comparator.

The pre-amp has two inputs: an unbalanced input for line level signals, with a gain factor of from 0 to 20, and a balanced input with a gain factor of from 0 to 500, for insertion of low level signals, for instance from a microphone or electric guitar.

The Envelope Follower reads the signal level of the input, and puts out a proportional voltage as an envelope at its own output.

The comparator generates a gate signal whenever the input goes above an adjustable trigger threshold.

Three LED's help you keep track of overload, the envelope, and the gate signal.
Read more
 3 in stock $70.18
Cat: 716920 Rel: 29 Jan 19 • View all Synth modules
 
Voltage-controlled panning module consisting of 2 linear VCA's - 8HP
Notes: A-134-1 is a voltage controlled universal panning and/or crossfader module. If the module is used a voltage controlled Panning device one audio signal is panned to two different outputs. If the module is used a voltage controlled Crossfader two audio signals are mixed to one common output. The module enables even compositions of both functions.

The module contains two linear high quality VCAs (made with CEM3381/PA381 until April 2013, SSM2164 from May 2013). VCA2 works in the opposite direction of VCA1 i.e. the more VCA1's loudness increases the more VCA2's loudness decreases. The panning or crossfading is adjusted with a control knob (manual control) and by two external control voltages, one equipped with an attenuator. Suitable control voltage sources are e.g. LFOs (A-145, A-146, A-147), envelope signals (A-140, A-141, A-142, A-119), random (A-118), Theremin (A-178) or a voltage coming from a MIDI-to-CV-Interface (A-190, A-191). The panning/crossfading is displayed with 2 LEDs.

A-134-1 has an audio input with attenuator for each VCA. If the audio input of VCA2 is not used the audio input of VCA1 is connected with audio in of VCA 2, i.e. the sockets are "normalled". The module has three audio outputs: Left Output (VCA1), Right Output (VCA2) and Mix. For Panning applications the outputs Left Out and Right Out are used. If the module is used as a Crossfader the Mix Output functions as output.

Module A-134-1 enables voltage controlled stereophonic panning effects (one audio signal distributed to two outputs), crossfading effects (two audio inputs mixed to one audio output with voltage controlled loudness proportion) and combinations of both effects.
Read more
 1 in stock $84.22
Cat: 731940 Rel: 11 Jun 19 • View all Synth modules
 
Compact two-channel VCA - 4HP
Notes: Module A-130-2 is the slim version of module A-132-3 and offers essentially the same features. But the distances between the controls are smaller and rubberized small-sized knobs are used. In return the front panel has 4 HP only which is half the width of the A-132-3. The module is primarily planned for applications where only limited space is available.

The module is composed of two identical voltage controlled amplifiers (VCA). Each VCA has a manual gain control (also named Initial Gain) and a control voltage input with attenuator. The character of the control scale can be switched to linear or exponential. All inputs and outputs are DC coupled. Consequently the VCAs can be used to process both audio and control voltages (e.g. for voltage control of the level of LFO or envelope signals). The signal input has no attenuator available but is capable to process up to 16Vpp signals (i.e. -8V...+8V) without distortion. For the processing of higher levels an external attenuator (e.g. A-183-1) is recommended.

The amplification range is 0...1. Even with a higher external control voltage the amplification remains at 1 (kind of "amplification clipping" at 1).

Controls (for each of both units):

- Gain: manual gain control (Initial Gain) in the range 0...1
- CV: attenuator for the CV input
- Lin/Exp: switches the VCA characteristic to linear or exponential, in center position the VCA is off (mute function)

Inputs and outputs (for each of both units):

- CV: control voltage input, min. +5V required for max. amplification (1) with CV control fully CW and Gain fully CCW
- In: signal input, max. 16Vpp (+8V...-8V) without distortion
- Out: signal output
Read more
 3 in stock $77.74
Cat: 731951 Rel: 11 Jun 19 • View all Synth modules
 
Quad passive switch - 4HP
Notes: A-182-2 is a simple passive module that contains four changeover switches, which are used to connect or disconnect the sockets of the corresponding socket triplet:

- In the upper position of the switch the upper socket of the corresponding socket triplet is connected to the centre socket
- In the lower position of the switch the lower socket of the corresponding socket triplet is connected to the centre socket
- In the centre position of the switch the sockets are not connected

Each unit of the module can be used to switch between two signals or to interrupt/connect a signal. In the last case the third socket of the triplet is not used.

The module is fully passive and both audio or control signals can be switched.
Read more
 2 in stock $59.38
Cat: 714707 Rel: 22 Jan 19 • View all Synth modules
 
4HP Eurorack module consisting of four buffer circuits for control voltages
Notes: Module A-180-4 is a fourfold CV buffer. Buffers are required if the control voltage coming from a CV source shows a voltage drop in case of changing loads or due to other reasons a buffering is required.

For the lower three units the input is normalled to the output of the above unit. That way the module can work as 1-in-4 buffered multiple provided that no signals are applied to the inputs of the three lower units.

Typical applications:

- Buffering the outputs of voltage controlled switches (e.g. A-150-1, A-150-8, A-151, A-152). Comment: in case of bidirectional switches it's not possible to integrate the buffers into the switching module because the direction is not known (i.e. which terminal of the switch is working as input and which as output). All electronic switches suffer from a small residual restistance that may cause a small voltage drop without buffering. This may become a problem especially when VCOs are controlled by the switched voltages.
- Buffering of CV interfaces, quantizers, slew limiter, S&H/T&H, sequencer etc. when VCOs are controlled by the CV (provided that the module in question does not feature a buffered output)
- Buffered multiple (similar to A-180-3)
Read more
 1 in stock $52.65
Cat: 577753 Rel: 06 Jun 19 • View all Synth modules
 
12dB multi-mode filter - 8HP
Notes: Module A-106-5 is a 12dB multimode filter that is based on the filter circuit of the Oberheim SEM module.

The filter is equipped with a band pass output and a combined low/notch/high pass output. For this output a control knob defines the relation between low and high pass signal. If both signals appear at the same level (i.e. middle position of the Mix knob) one obtains a notch filter. Otherwise the low or high pass signal predominates.

The module does not feature self-oscillation in contrast to most of the other filters of the A-100 system.

The module generates a distorted audio signal if the level control is set to about 50% (i.e. centre position) or more with A-100 standard signals like VCOs.
Read more
 4 in stock $79.90
Cat: 745792 Rel: 10 Sep 19 • View all Synth modules
 
Dual trigger modifier, consisting of two trigger inverters for gate, clock or trigger signals - 4HP
Notes: Module A-165 (Dual Trigger Modifier) contains two separate trigger modifiers, to use with logical/digital levels (gate, clock, trigger). Each half of the module enables signals generated by the A-100 to communicate with other instruments (such as an external sequencer) or is simply used where you want to reverse a trigger polarity.

Whatever signal is patched into the input, inverted by the module, and fed out of the Inv. Out (inverted output) socket. At the same time, a trigger signal of roughly 50 ms is generated every time an edge of the trigger pulse is sensed (negative as well as positive). This trigger signal is available at the +/- output.

Two LEDs act as indicators showing the level of signal available at the two outputs.

When both units are daisy-chained the module can be used as level shifter for gate/trigger/clock signals (from min. +2,5V up to +12V)
Read more
 1 in stock $60.48
Cat: 738640 Rel: 09 Jul 19 • View all Synth modules
 
Voltage controlled sine-LFO with four separate, phase shifted outputs - 8HP
Notes: Module A-143-9 is a derivative of our planned thru-zero quadrature VCO. It is a voltage controlled sine LFO with 4 outputs. The phase shift between the outputs is 90 degrees. The sine shifted by 90 degrees is also called cosine, the sine shifted by 180 degrees is nothing but the inverted sine, and the sine by 90 degrees is nothing but the inverted cosine.

The frequency range is from some minutes to frequencies beyond audio with three ranges selected by a toggle switch:

- Switch position H: about 30 Hz ... 3.5 kHz with the manual frequency control ("Frq."), beyond 20 kHz with additional external CV
- Switch position M: about 1 Hz ... 150 Hz with the manual frequency control ("Frq.")
- Switch position L: about 0,1 Hz ... 10 Hz with the manual frequency control ("Frq."), down to several minutes with additional external CV

Two exponential frequency control inputs are available: CV1 without attenuator and CV2 with polarizer. Consequently the module can be used even as an experimental sine VCO but does not feature an exact 1V/oct CV input! The precision CV input will be left to the thru-zero quadrature VCO.

Two LEDs display the positive and negative share of the sine output.

The core of the module is a so-called quadrature circuit that generates a sine a cosine signal with very low distortion. The quality of the sine/cosine signals are much better than those generated by a waveform converter with a sawtooth or triangle signal as starting point.

The output levels are about 5 Vss (+/-2.5V) but can be adjusted internally by a trimming potentiometer (P5 "Shape").

Typical applications:

- External sine/cosine oscillator for the frequency shifter A-126
- Modulations with pure sine/cosine waveforms
- Quadrature/barberpole effects (e.g. with the voltage controlled mixer A-135)
- Experimental sine/cosine VCO (e.g. for FM sounds)

Many users suggested to add a common output level control, i.e. four VCAs with one common control (manual + CV without attenuator + CV with polarizer) for the output levels. This is why we also designed the Quad VCA module A-132-2 with the possibility of an internal default connection to the four outputs of the A-143-9 (no soldering required, short 10 pin flat cable with removable connectors on both ends).

The A-143-9 is also a meaningful addition for the Frequency Shifter module A-126. It enables frequency shifting even below 50 Hz generating e.g. these mellow beat sounds with a few Hz frequency shifting only. The following document describes how to connect the A-126 and the A-143-9: A126_A143_connection.pdf.

The thru zero version of the A-143-9 with temperature compensation is the module A-110-4.
Read more
 1 in stock $78.82
Cat: 577763 Rel: 10 Jul 19 • View all Synth modules
 
8HP Eurorack module featuring two identical VCA's
Notes: Module A-132-3 is composed of two identical voltage controlled amplifiers (VCA). Each VCA has a manual gain control and a control voltage input with attenuator. The character of the control scale can be switched to linear or exponential. All inputs and outputs are DC coupled. Consequently, the VCA's can be used to process both audio and control voltages. The input has no attenuator available but is capable to process up to 16Vss signals (i.e. -8V...+8V) without distortion.
Read more
 1 in stock $98.74
Cat: 703570 Rel: 05 Oct 18 • View all Synth modules
 
24dB low pass filter based on a Curtis filter circuit - 8HP
Notes: Module A-122 is a voltage-controlled low-pass filter, which filters out the higher parts of the sound spectrum, and lets lower frequencies pass through.

The cut-off frequency determines the point at which filtering takes effect. You can control this manually, or by voltage control (filter modulation, for instance by an LFO). Two CV inputs are available.

The cut-off slope is -24 dB/octave. The circuitry uses a Curtis chip, and is very similar to the classic Oberheim filter sound. Because of its different circuitry and controls, the A-122 has a considerably different sound to the A-120 'Moog-like' filter, especially in the way the resonance behaves.

Voltage controlled resonance: on the A-122, resonance can be controlled not just manually, but by voltages as well, right up to self-oscillation. In this case, the filter behaves like a sine wave oscillator.
Read more
 2 in stock $96.10
Cat: 703564 Rel: 08 Oct 18 • View all Synth modules
 
Analogue noise/random with black faceplate & custom knobs - 8HP
Notes: Module A-118 is (as you might have guessed) a noise and random voltage generator. It produces three types of signal: white noise, coloured noise, and random voltage. The noise signal is generated 100% analogue by amplification of the noise of a transistor. White and coloured noise can be used as audio sources, and also, in conjunction with a sample & hold module, as control voltages, and the random voltage is a useful source of voltage control, especially for its low frequency content.

The A-118 gives you the ability to mix the relative amounts of Red (low frequency component) and Blue noise (high frequency component) in the coloured noise output.

There are knobs to control the rate of change and amplitude of the random voltage, and two LEDs indicate the state of the voltage at any one time.
Read more
 1 in stock $66.94
Cat: 745778 Rel: 10 Sep 19 • View all Synth modules
 
Two independent voltage controlled switches in one module - 4HP
Notes: Module A-150-1 (Dual VCS) contains two separate voltage-controlled switches.

Each switch has a control voltage input, a common Out / Input, and two In / Outputs. The switches are bi-directional: they can work in both directions, so can connect one input to either of two outputs, or either of two inputs to one output. Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Two LEDs show which in / output is active (i.e. which is connected to the common out / input).
Read more
 2 in stock $53.99
Cat: 716922 Rel: 29 Jan 19 • View all Synth modules
 
Dual crossfader module for voltage controlled morphing between two audio or CV signals
Notes: Module A-134-2 contains two identical voltage controlled crossfader units.

Each unit has two voltage controlled amplifiers (VCAs) with opposite control behaviour available. The outputs of the two VCAs are mixed together to obtain a common output. The behaviour of the control voltage inputs can be chosen with an internal jumper:

Symmetrical mode: If the corresponding jumper is not set both VCAs of the crossfader have the same 50% amplification with zero CV. If the applied CV becomes positive the amplification of VCA1 decreases and those of VCA2 increases in the same way. A negative CV has the opposite result. The CV voltage range to obtain the maximum/minimum positions of the crossfader is about -2.5....+2.5V. This mode is useful for bidirectional (i.e. positive and negative) control voltages, for example LFO or joy stick (adjusted to 0V CV in centre position).

Asymmetrical mode: If the corresponding jumper is set VCA2 is fully closed and VCA1 has full 100% amplification with zero CV. If the applied CV becomes positive the amplification of VCA1 decreases and those of VCA2 increases in the same way. The CV voltage range to obtain the maximum/minimum positions of the crossfader is about 0...+5V. A negative CV has no function in this mode. This mode is useful for unidirectional (i.e. only positive) control voltages, for example ADSR, ribbon controller or Theremin control voltage.

The CV input of the upper unit (CV1) is normalled to the CV input of the lower unit (CV2). I.e. if no plug is inserted to CV2 the CV input of the upper unit (CV1) also controls the lower unit.

The second signal input of the upper unit (In1B) is normalled to the first signal input of the lower unit (In2A). I.e. if no plug is inserted into In2A the signal In1B is used as the first signal input of the second unit.

As the inputs and outputs are DC coupled the module can be used for both audio and control voltage signal processing.
Read more
 2 in stock $71.26
Cat: 738621 Rel: 10 Jul 19 • View all Synth modules
 
Voltage controlled envelope generator with decay parameter - 8HP
Notes: Module A-142-1 is a voltage controlled envelope generator. The only time parameter is decay (like TB303). Decay may be adjusted manually and via voltage control input (with attenuator). The envelope output is displayed with LED control. Additionally from the envelope signal a Gate signal and an inverse Gate signal with adjustable threshold is derived. LED control for Gate output. Thus one obtains a voltage controlled Gate additionally or alternatively to the envelope signal with voltage controlled duration.

The attack time is fixed to about 0.2 ms, the shortest decay time is about 2 ms. By changing the value of a capacitor the shortest time can be modified (details can be found here: A100_Capacitors.htm).

Typical applications: dynamic control of decay e.g. in combination with the Analog/Trigger Sequencer A-155, voltage controlled trigger delay functions (like A-162, but voltage controlled).
Read more
 1 in stock $79.90
Cat: 738616 Rel: 10 Jul 19 • View all Synth modules
 
Stereo headphone amplifier - 6HP
Notes: The A-139-2 is a headphone amplifier module with two mono inputs and a stereo headphone output. It can be used for driving small loudspeakers, LED strips, small magnets etc.

- Two-channel headphone amplifier
- Two audio inputs with level controls
- Input 1 is normalled to Input 2
- Common loudness/master level control
- Headphone output (stereo 1/4" jack socket)
- Max. output power ~ 2 W per channel (@ 8 Ohm load)
- DC coupled inputs and outputs (i.e. also useful for other applications like small loudspeakers, lamps, LEDs, magnets, motors - provided that the power is sufficient)
Read more
 1 in stock $52.91
Cat: 738645 Rel: 10 Jul 19 • View all Synth modules
 
Low frequency oscillator with adjustable waveform - 8HP
Notes: Module A-146 (LFO 2) is a Low Frequency Oscillator, which produces periodic control voltages over a wide range of frequencies.

The LFO can be used as a modulation source for a series of modules (for instance pulse width and/or frequency modulation of a VCO, modulation of a VCF cut-off frequency, amplitude modulation with a VCA).

Three outputs are available, with different waveforms: sawtooth / triangle; square wave, and positive-voltage square wave.

The waveform is continuously adjustable from rising sawtooth, through triangle to falling sawtooth. The same control affects the pulse width of the square wave.

A three-way switch can select one of three frequency ranges, spanning from one cycle every few minutes, at the lowest, up to audio frequency at the highest.
Read more
 1 in stock $66.94
Cat: 738632 Rel: 09 Jul 19 • View all Synth modules
 
Quad Decay featuring four simple envelope generators - 8HP
Notes: Module A-142-4 contains four simple envelope generators. The only time parameter is Decay and can be adjusted manually by means of the Dec. control in the range 2 ms ... 2 seconds. The attack time can be adjusted internally by means of a separate trimming potentiometer for each sub-unit in the range 1 ms ... 15 ms. The factory setting is about 3 ms. This is the attack time of the TB303. Each envelope output has a LED control available. The trigger inputs are normalled (1 -> 2 -> 3 -> 4).

Suggestions for modifications:

Each sub-unit has a pin header with two pins available. When the two pins are shortened (e.g. by means of a jumper or a toggle switch connected to the two pins) the corresponding sub-unit changes to a loop mode. In this mode the unit is triggered by itself like an LFO..

By changing the value of a capacitor the time range can be modified (e.g. 0.2 ms ... 0.2 seconds or 20 ms ... 20 seconds)
Read more
 1 in stock $96.10
Cat: 714708 Rel: 25 Mar 19 • View all Synth modules
 
Controller module for static & dynamic control of RGB LED stripes - 4HP
Notes: Module A-197-3 is a control unit for RGB LED stripes. The LED stripe is glued e.g. to the inner edges of the cases A-100P6/P9/PMS6/PMS9/PMS12 to illuminate the modules and patching statically or dynamically. Especially during live events the dynamic illumination in sync with the sound is an eye-catcher. Each colour (red, green, blue) has available a manual control for the background brightness and a CV input with attenuator that enables the dynamic brightness controlled by other control voltages of the modular system. For example three envelopes can be used which also control the loudness or filtering of sound processing modules. But even other control applications are possible, e.g. LFO, random voltages, clock/gate/trigger signals, sequencer, Midi-to-CV.
Read more
 1 in stock $80.98
Cat: 692504 Rel: 18 Jun 18 • View all Synth modules
 
18dB low pass filter based on a modified Moog cascade - 8HP
Notes: Module A-103 is a voltage controlled low pass filter with 18dB/octave slope. The circuit is based on a modified transistor ladder (Moog ladder) and is a reproduction of the legendary TB303 filter.

As for the rest the A-103 is identical to the A-120 Moog low pass filter (same controls, inputs/outputs) only the filter sound is different.
Read more
 2 in stock $80.98
Cat: 692503 Rel: 18 Jun 18 • View all Synth modules
 
Reproduction of the legendary British diode lowpass filter - 8HP
Notes: Module A-102 is a reproduction of the legendary low pass filter design that uses diodes in the filter stage as frequency controlling elements - resulting in "strange" resonance behaviour and frequency response, as resonance and frequency are not independent from another.

As for the rest, the A-102 is identical to the A-120 Moog low pass filter, the A-103 (18dB TB303 Filter) i.e. the same controls, inputs and outputs. Only the filter sound is different:

- Manual control of filter frequency
- 3 CV inputs (CV1, CV2, CV3), 2 of them with attenuator (CV2, CV3)
- Input level control
- Resonance control up to self-oscillation (depends upon the frequency setting for the A-102)
Read more
 1 in stock $79.90
Cat: 745777 Rel: 10 Sep 19 • View all Synth modules
 
Expansion module to the A-149-1
Notes: A-149-2 is an extension module for A-149-1. It makes available 8 digital random voltages (i.e. only low/high states like a gate signal). The outputs are controlled by the "Quantized Random Voltages" section of the assigned A-149-1 and correspond to the 8 digital outputs of the shift register that is used to generate the Quantized Random Voltages. As the alteration of the A-149-2 outputs is clock controlled by the Clk In of the "Quantized Random Voltages" section of the A-149-1 the A-149-2 can be used to create random rhythmical sequences.

The A-149-2 requires the A-149-1 and has to be mounted directly to the left or right of the A-149-1 as an internal ribbon cable connection has to be established between A-149-1 and A-149-2.
Read more
 1 in stock $56.16
FORTHCOMING
Doepfer A-182-1 Switched Multiples Module Doepfer A-182-1 Switched Multiples Module Doepfer A-182-1 Switched Multiples Module
Cat: 751724 Rel: 23 Oct 19 • View all Synth modules
 
Eurorack passive multi-connector - 6HP
Notes: Module A-182-1 is a simple passive multi-connector similar to the multiples modules A-180-1/A-180-2. In contrast to modules A-180-1/2 each socket is equipped with a 3-position switch that allows to connect the corresponding socket to the internal bus #1 (left position), bus #2 (right position) or to turn the socket off (centre position).

Examples:

- All switches in left position or all switches in right position: 8-fold multiple

- Four switches in left position and four switches in right position: two 4-fold multiple

- X switches in left position, Y switches in right position and Z switches in centre position: two separate multiples with some sockets turned off
Read more
coming soon $52.92
Cat: 710942 Rel: 29 Nov 18 • View all Synth modules
 
Dual VCA with linear response - 4HP
Notes: Module A-132-1 (Dual Low Cost VCA) contains two voltage controlled amplifiers, with a linear response most suited to regulating the level of control voltages (ADSR amount, level of vibrato effect, etc).

In non-critical situations, though, its VCAs can be used to control audio signals.

Amplification is governed by the sum of the voltages patched into the two CV inputs.
Read more
 1 in stock $66.94
Cat: 710951 Rel: 29 Nov 18 • View all Synth modules
 
Two voltage controllable amplifiers which can amplify positively or inverted - 8HP
Notes: A-133 is a special dual voltage controlled amplifier that enables both positive and negative amplifications. Negative amplification means in this context that the signal is inverted. The main application of the module is the processing of control voltages, e.g. ADSR or LFO but the module can be used also for audio applications (e.g. as a waveshaper, see patch examples below).

The amplification range is about -2.5....0....+2.5 (other amplification ranges for small additional charges, e.g. -1...+1 or -5...+5). Amplification can be adjusted manually (Man control) and by an external control voltage with attenuator (CV). The present amplification is displayed with two LEDs: one for positive and one for negative amplifications (not a signal display but amplification display, similar to A-134).
Read more
 1 in stock $85.07
FORTHCOMING
Doepfer A-184-1 Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module Doepfer A-184-1 Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module Doepfer A-184-1 Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module
Cat: 751756 Rel: 23 Oct 19 • View all Synth modules
 
4HP Eurorack module featuring a combination of 3 functions
Notes: Module A-184-1 is the combination of three functions:

- Ring Modulator
- Sample&Hold/Track&Hold unit
- Slew Limiter

The same functions are actually already available in other modules (e.g. A-114, A-148, A-170). But in many systems it's not necessary to have two ring modulators (A-114) or two S&H units (A-148) or two slew limiters (A-170) available. That's why we have compiled these function in one small 4 HP module.

The upper section is nothing but half of an A-114, i.e. a ring modulator with the usual X/Y inputs and the X*Y output. Inputs and outputs of this sub-unit are AC coupled, i.e. suitable only for audio signals. A detailed explanation of a ring modulator can be found on the A-114 info page.

The lower section is a Sample & Hold (S&H) / Track & Hold (T&H) unit (same as half of an A-148) followed by a slew limiter (same as the upper section the A-170). A toggle switch is used to set the mode to S&H or T&H. In S&H mode the unit picks out a sample from the voltage at the SH input at the rising edge of the trigger signal input. In T&H mode the output follows the input voltage as long as the level of the trigger signal is high. As soon as the trigger signal turns low, the last voltage is stored. The trigger input is internally normalled to high, i.e. the unit works just as a slew limiter in T&H mode when no trigger signal is applied.
Read more
coming soon $96.11
Cat: 710948 Rel: 29 Nov 18 • View all Synth modules
 
Four identical voltage controlled amplifiers with exponential control scales - 6HP
Notes: Module A-132-4 contains four identical voltage controlled amplifiers (VCA) with exponential control scales. Each VCA has two control voltage inputs (C1, C2), a signal input (In) and a signal output (Out). The control voltage inputs C1 and the signal inputs can be normalled by means of internal jumpers, i.e. the corresponding input signals of unit #1 can be connected to the switching contacts of unit #2. Those of unit #2 can be normalled to unit #3 and those of unit #3 to unit #4. If the normalling is not desired the jumpers have to be removed. In addition the sum of all four outputs is available (bottom left socket with the sum sign). Therefore unit #4 has only one control voltage input (only C1, no C2). If desired this socket can be jumpered as control voltage input 2. But then the sum signal is no longer available as a socket (only as an internal pin). For each VCA output a jumper is available that determines if the output signal of the corresponding VCA is added to the sum signal. From the factory all four jumpers are set (i.e. all four VCA output signals are added). By removing of one or more of the jumpers one can choose which VCA output is added to the sum. The jumpers can be replaced by switches too.

Technical notes:

The control scale for each VCA is about 12dB/V (i.e. 1 V CV decrease corresponds to 12dB level decrease and 1 V CV increase corresponds to 12dB level increase). 0V CV corresponds to about -60dB (i.e. about attenuation by 1000). +5V CV corresponds to about 0dB (i.e. no attenuation or amplification = 1). The full attenuation/amplification range is about -90dB ... + 20dB. Attenuations below -60dB require a negative control voltage, amplifications beyond 0dB require a control voltage more than +5V. For the first CV input of each unit (CV1) an internal trimming potentiometer (attenuator) is available to adjust the control scale for other voltage ranges (e.g. 0...+8V for A-140 envelope control or 0...+10V for external 10V control voltages). To obtain another CV scale even for CV2 an attenuator (e.g. A-183-1) can be used. If an amplification offset is required (e.g. for zero-symmetrical control voltages like LFO) an external offset generator with attenuator/polarizer (e.g. A-183-2) is recommended.

The A-132-4 uses a circuit with four exponential VCAs (SSM2164/V2164). Unfortunately there is no easy way to obtain a linear scale for the VCAs (actually two exponential VCAs are required to obtain a linear VCA, that's how e.g. the A-132-1 and A-132-3 work).
Read more
 1 in stock $85.31
Cat: 577766 Rel: 15 Aug 18 • View all Synth modules
 
Analogue noise & random module - 8HP
Notes: Module A-118 is a noise and random voltage generator. It produces three types of signal: white noise, coloured noise, and random voltage.

White and coloured noise can be used as audio sources, and also, in conjunction with a sample & hold module, as control voltages, and the random voltage is a useful source of voltage control, especially for its low frequency content.

The A-118 gives you the ability to mix the relative amounts of Red (low frequency component) and Blue noise (high frequency component) in the coloured noise output.

There are knobs to control the rate of change and amplitude of the random voltage, and two LEDs indicate the state of the voltage at any one time.
Read more
 2 in stock $63.70
Cat: 716939 Rel: 29 Jan 19 • View all Synth modules
 
Logarithmic mixer for mixing up to four signals to one output - 8HP
Notes: Module A-138 is a four channel mixer, which can be used with either control voltages or audio signals. Each of the four inputs has an attenuator, and there's a master attenuator, so that the mixer can be used at the end of the audio chain - i.e. it can be used to interface directly with an external mixer, amplifier, etc.

A-138b features potentiometers with logarithmic response, so especially suitable for audio signal mixing.

Vintage Edition with a black faceplate and custom knobs.
Read more
 1 in stock $71.26
Cat: 744271 Rel: 05 Oct 18 • View all Synth modules
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


Module A-122 is a voltage-controlled low-pass filter, which filters out the higher parts of the sound spectrum, and lets lower frequencies pass through.

The cut-off frequency determines the point at which filtering takes effect. You can control this manually, or by voltage control (filter modulation, for instance by an LFO). Two CV inputs are available.

The cut-off slope is -24 dB/octave. The circuitry uses a Curtis chip, and is very similar to the classic Oberheim filter sound. Because of its different circuitry and controls, the A-122 has a considerably different sound to the A-120 'Moog-like' filter, especially in the way the resonance behaves.

Voltage controlled resonance: on the A-122, resonance can be controlled not just manually, but by voltages as well, right up to self-oscillation. In this case, the filter behaves like a sine wave oscillator.
Read more
 1 in stock $92.48
Cat: 684442 Rel: 30 Oct 18 • View all Synth modules
 
Voltage controlled highpass filter - 8HP
Notes: A-123-2 is a voltage controlled high-pass filter with four filter outputs (6, 12, 18 and 24dB slope). It also features voltage control of the resonance.

These controls and in/outputs are available:

- Audio In with attenuator (Lev)
- Manual Frequency control (Frq)
- FCV1: Frequency control input (~ 1V/oct)
- FCV2: Frequency control input with polarizer
- QCV: Resonance control input with attenuator
- Manual Resonance control (Q)
- 6dB Output
- 12dB Output
- 18dB Output
- 24dB Output
Read more
 1 in stock $96.11
Cat: 684462 Rel: 22 May 18 • View all Synth modules
 
Electronic switch with up to four steps - 4HP
Notes: Module A-151 (Quad Sequential Switch) is like an electronic four-position rotary switch.

It includes trigger and reset inputs, four in/outputs, and a common out/input. Each time a pulse is received at the trigger input socket, the common out/input is connected to the next in/output. After the fourth in/output, the next trigger makes it step back to the first again, and so on. A positive pulse at the reset input switches the out/input immediately back to the first in/output. Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Four LED's indicate the active in/output (ie. the one that is connected to the out/input at any particular time).
Read more
 4 in stock $60.46
FORTHCOMING
Doepfer A-170v Dual Slew Limiter Module (vintage edition) Doepfer A-170v Dual Slew Limiter Module (vintage edition) Doepfer A-170v Dual Slew Limiter Module (vintage edition)
Cat: 751702 Rel: 23 Oct 19 • View all Synth modules
 
Two separate slew limiters for generating portamento effects - 8HP
Notes: Module A-170 contains two separate slew limiters, also known as portamento controllers or integrators. The first SL has just one joint control, which sets both rise and fall times (c. 0 ...10 sec). The second SL has separate controls for rise and fall times, and can therefore be used as a simple AR envelope generator. Over and above this, you can set the overall range for these parameters, with a three-position switch, as on the full ADSRs.

Both slew limiters have two LEDs each, to show the state of the rising and falling voltages.


Additional technical remarks: If the upper slew limiter is used for precision applications (e.g. portamento/glide of one or more VCOs) a buffer (e.g. A-185-1 or A-185-2) is recommended between the A-170 output and the VCO(s) input(s). The reason is a small voltage drop that is caused by the protection resistor at the A-170 output. An A-185-1 or A-185-2 connected between the A-170 and the VCO(s) avoids that voltage loss. For all A-170 manufactured later than May 2009 (recognizable by the label "Version 2" on the pc board) this remark is not valid as these modules are equipped with an additional voltage buffer at the output.

The lower slew limiter cannot be used for precision applications because of the voltage loss caused by the diodes of the circuit.
Read more
coming soon $77.75
FORTHCOMING
Doepfer A-172 Maximum/Minimum Selector & Rectifier Module Doepfer A-172 Maximum/Minimum Selector & Rectifier Module Doepfer A-172 Maximum/Minimum Selector & Rectifier Module
Cat: 751706 Rel: 23 Oct 19 • View all Synth modules
 
Module for processing/mixing of control voltages - 4HP
Notes: A-172 is a minimum/maximum selector module and is equipped with four analogue inputs and two analogue outputs (minimum, maximum). The main application of the module is the processing/mixing of control voltages, e.g. random voltages, ADSR, LFO, S&H, ribbon CV, theremin-CV and similar, but even for audio signal processing the module can be used (e.g. several outputs of the same or different VCOs).

The module permanently picks the maximum resp. minimum voltage out of the four input signals and outputs these voltages to the maximum resp. minimum jack socket.

To adjust offset and amplitude for each input independently (i.e. to bring the signal into the right "position" with the desired level) we recommend combining the module with the A-129-3 Slew Limiter/Attenuator/Offset Generator (see patch example below). The other sketch below shows the basic principle of the max/min module by means of three sine waves (e.g. three LFOs) with different frequencies and different levels.

The module can be used also as a simple half-wave rectifier.
Read more
coming soon $51.03
FORTHCOMING
Doepfer A-174-2 Modulation Wheels CV Source Module Doepfer A-174-2 Modulation Wheels CV Source Module Doepfer A-174-2 Modulation Wheels CV Source Module
Cat: 751707 Rel: 23 Oct 19 • View all Synth modules
 
Modulation wheel module with two wheels - 14HP
Notes: A-174-2 is a modulation wheel module with two wheels. The factory setting is a spring loaded wheel at the left side with bipolar voltage output (i.e. 0V in centre position, positive voltage in the upper range, negative voltage in the lower range, voltage range about -5.5 V ... 0V ... +5.5 V) and a wheel without spring at the right side with positive voltage output (i.e. 0V in the lowest position and positive voltage when operated, voltage range about 0...+8 V). For the spring loaded wheel a voltage "plateau" around 0 V is preset (jumper) so that the output voltage is 0 V in a small area near the centre position.

By means of jumpers the factory settings can be changed. For each wheel two jumpers are available: one for the voltage range (positive or bipolar) and one for the voltage plateau around 0 V. If these settings are changed even the wheels have to be re-adjusted mechanically. Therefore, such modifications should be carried out by a qualified person only. By request the module is available from the factory even with two wheels both with or without springs (additional charges Euro 10.00 for each change).

Important note for module mounting: As the potentiometer of the left wheel projects about 10 mm the rim of the front panel a 2 or 4 HP blind panel has to be mounted left from the module - unless the module left to the A-174-1 has sufficient space in this area (e.g. A-174-1).
Read more
coming soon $77.75
FORTHCOMING
Doepfer A-177-2 External Foot Controller II Module Doepfer A-177-2 External Foot Controller II Module Doepfer A-177-2 External Foot Controller II Module
Cat: 751715 Rel: 23 Oct 19 • View all Synth modules
 
Foot controller interface - 8HP
Notes: Economically priced module for connecting one foot controller and one double foot switch for control A-100 functions by means of the feet. For example, the frequency of a filter or the loudness can be controlled by a foot controller, but even other parameters like LFO frequency, modulation depth, phasing, pitch or any other voltage controlled parameter. The gate outputs controlled by the double foot switch can be used e.g. to trigger an envelope generator or to start/stop a sequencer. Even a single foot switch can be used if only one gate signal is required.

A special application of the A-177-2 is the usage within a Trautonium replica. The foot switches can be used to switch the mixtures of the subharmonic oscillator A-113. The foot controller can be used to control the overall loudness in combination with a VCA.

A-177 is compatible with the foot controllers FP5 and double foot switch VFP2. The Foot controller and double foot switch are not included with the module. If you want to use another foot controller or foot switch it has to be compatible to FP5 or VFP2.

If the foot controller FP5 is used the CV output range is about 0...+8V. The gate output levels are 0/+12V in combination with the VFP2 (foot switch not operated = 0V, foot switch operated = +12V).
Read more
coming soon $52.92
FORTHCOMING
Doepfer A-178 Theremin Control Voltage Source Module Doepfer A-178 Theremin Control Voltage Source Module Doepfer A-178 Theremin Control Voltage Source Module Doepfer A-178 Theremin Control Voltage Source Module
Cat: 751716 Rel: 23 Oct 19 • View all Synth modules
 
Theremin controller module - 8HP
Notes: Theremin module for generating a variable control voltage by approaching/removing hand to/from an antenna. The distance range is about 30-40 cm. Additionally the module is equipped with a Gate output with adjustable threshold level. Controls/Inputs/Outputs: antenna input, offset (knob for zero adjust), 2 x CV out, 2 x LED (for CV control positive/negative and zero offset adjust).

To simulate the original Theremin two A-178, a VCO (e.g. A-110) and a linear VCA (e.g. A-130 or A-132) are required. But of course the A-178 can be used to control other functions in the A-100 (e.g. filter frequency, modulation depth and/or speed, tempo, attack/decay time and so on).

The CV output voltage of the A-178 can range - according to the setting of the front panel controls - from -10V...+10V. The gate output switches from 0V to about +10V.

Applications:

- Controlling any voltage controlled parameter of the A-100, e.g. pitch or pulsewidth (VCO A-110), loudness (VCA A-130/131/132), panorama (A-134), filter frequency or resonance (A-120/121/122/123), phasing (A-125), frequency shift (A-126), resonance peaks (A-127), envelope parameters (A-141/142), tempo (A-147)

- Triggering of A-100 activities via gate with adjustable threshold, e.g. starting an envelope (A-140/141/142), Start/Stop of a sequence (A-155), any switching function (A-150/151)

- Conversion into MIDI control change messages is possible with the A-192.

If two or more A-178 are used the distance between the modules/antennas should be at least 40-50 cm. Otherwise the antennas may affect each other.
Read more
coming soon $96.11
Cat: 577776 Rel: 29 Nov 17 • View all Synth modules
 
Four channel mixer module - 8HP
Notes: Module A-138 is a four channel mixer, which can be used with either control voltages or audio signals. Each of the four inputs has an attenuator, and there's a master attenuator, so that the mixer can be used at the end of the audio chain, i.e. it can be used to interface directly with an external mixer, amplifier, etc.

The A-138b has potentiometers with logarithmic response, so is especially suitable for audio signal mixing.
Read more
 3 in stock $57.22
Items 1 to 50 of 71 on page 1 of 2
1  2  »

Filter

Saved Searches
Save current search
Release Date
Featured
Close