100% Secure Shopping

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Secure Shopping

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Options
Items 1 to 6 of 6 on page 1 of 1
Cat: 754307 Rel: 28 Oct 19
 
Quad voltage controlled filter module
Notes: Tone is a quad, voltage controlled filter with low pass and band pass outputs. Its four channel architecture enables the intuitive patching of shimmering, polyphonic textures. The 24dB slope provides a warm, buttery character. Self oscillation allows each channel to double as a sine wave oscillator with v/oct tracking across four octaves. Cascade OTA topology. A perfect match for the Chord.
Read more
 1 in stock $284.11
Click for better price!
or call +44 20 7424 1960
quote 754307
Cat: 751766 Rel: 23 Oct 19
 
DSP based effects module - 18HP
Notes: Module A-187-1 is a DSP based effects module. Four parameters of the selected digital effect are voltage controlled. The main effect (e.g. reverb, delay, pitch-shifter, equalizer) is selected by the two small buttons effect up/down. The upper row of the display shows the effect that is currently selected. In the lower row the four parameters are shown as well as a small bar left from the abbreviation that displays the current parameter value. Each parameter can be adjusted manually (upper potentiometer row) and modified by external control voltages (lower row of the potentiometers and upper row of the sockets). The lower row of the sockets contains the two audio inputs and outputs.

Another button (bypass) is used to turn the effect on/off. When bypass is chosen the upper line of the display shows in turn "BYPASS" and the name of the pre-selected effect. In the bypass mode another effect can be pre-selected and called-up by pressing the bypass button again. Even the effect parameters can be adjusted and are displayed with the bar graphs. But they become effective not before the bypass mode is left.

The module is equipped with two audio inputs and two audio outputs because the DSP board features stereo audio processing. The audio inputs can process usual A-100 signal levels without clipping/distortion. For higher levels external attenuators (e.g. A-183-1) or VCAs may be used.

A ready-made DSP board is used inside the A-187-1 module. Consequently, only these effects and parameters are available that are supported by the DSP module. Some parameters can be changed only in steps or with audible artefacts. The DSP board has 20 Bit DA and AD converter with 32 kHz sample rate available. The inter sound processing uses 24 Bit.
Read more
 1 in stock $261.51
Click for better price!
or call +44 20 7424 1960
quote 751766
Cat: 734884 Rel: 15 Oct 19
 
6HP VCO with auto-tuning & octave shift
Notes: Simplified version of the Furthrrrr Generator dual VCO, inspired by Don Buchla's designs. Through-zero linear FM, wavefolding, sub-oscillator and auto tuning. Proper west coast synthesis at its best.

Supplier's notes:
The Endorphin.es Godspeed is sort of the single oscillator version of the famous Furthrrr Generator. From its big brother it takes over the digital Thru-Zero core and the legendary wavefolder. But it also has new features like a sub-oscillator output and an immensely practical autotune function.

Especially for people starting with a modular system this oscillator is highly recommended. On 6HP it delivers all the features (and more) needed for diving into the depths of West-Coast-Synthesis!
Read more
 5 in stock $252.89
Click for better price!
or call +44 20 7424 1960
quote 734884
Cat: 755446 Rel: 07 Nov 19
 
Precision voltages module - dark edition
Notes: Sometimes real precision is required with pitch control voltages - this module features a super accurate "Cal" output, which is accurate to <1mV over 20V, translates to one cent over 20 octaves! It is ideal for calibrating the scaling of VCO's, indeed we have been using our own version of this circuit to calibrate our own MiniMod VCO's for the last three years.

As well as being a precision voltage source it is also a very accurate voltage adder, it has two channels (A & B) and both full volts (octaves) or 1/12th volt increments (notes) can be either added to or subtracted from the incoming signal. Perfect for adding a voltage offset to the output of a sequencer or it can be used to add switchable octaves to a VCO which only has course and fine tunes controls.

It also has a "mix" output, which allows either A channel on its own, or with the three way toggle switch channel B can either be added to, or subtracted from channel B, and this is in addition to the addition and subtraction per channel mentioned earlier.

Dimensions: 10HP wide, 26mm Deep
Read more
 2 in stock $232.45
Click for better price!
or call +44 20 7424 1960
quote 755446
Cat: 749081 Rel: 25 Oct 19
 
Eurorack instrument interface with Neutrik combo connector - 8HP
Notes: Instrument Interface is a Eurorack pre-amp capable of bringing any type of audio signal to modular levels, thanks to its amplification circuit.

The module can drive regular and condenser microphones (+48V Phantom Powered), as well as Instrument and Line signals with a very low distortion ratio.

Going further from the regular re-amp operation, Instrument Interface offers some additional extra functions like a Trig/Gate extractor and Envelope Follower circuits, allowing you to use the character of your audio signal in more creative ways.
Read more
MRP:$282.82 SAVE 22%
 7 in stock $220.61
Click for better price!
or call +44 20 7424 1960
quote 749081
Cat: 755403 Rel: 12 Nov 19
 
Bucket brigade delay module - 30HP
Notes: A-188-2 is another module that is based on a so-called Bucket Brigade Device (BBD). If you are not familiar with BBDs please refer to the A-188-1. There you can find some details about this special type of circuits.

The main difference between A-188-1 and A-188-2 is the type of BBD circuit that leads to completely different module principles and sounds. The A-188-1 uses different single BBD chips with one signal input and one signal output only. In contrast the A-188-2 uses as so-called tapped BBD that has available six outputs - the so-called taps after the BBD stages 396, 662, 1194, 1726, 2790 and 3328. In the A-188-2 we use this special BBD circuit (MN3011) to obtain these module features:

The module has available two separate mixing sub-units. For both mixers the levels and polarities of each BBD output can be adjusted to obtain two different mixtures of the BBD outputs. A new type of potentiometers with centre detent and centre terminal is used for the BBD mixing controls to have a better feel for the neutral position. Each mixer has a wet/dry control at its output that allows choosing between the pure input signal (original), the BBD mix or anything in between. The two outputs can be treated as stereo outputs but it is also possible to use one of the outputs for other applications (details in the next paragraph).

The A-188-2 has a feedback section available that is very similar to the one in the A-188-1. But as we now have 6 different BBD outputs available 6 different feedback types are possible. The feedback input socket is normalled to the "396" output (not to "1194" as shown in the scheme, the front panel is correct). But by patching the feedback socket to any of the single output sockets another BBD tap can be used for the feedback to obtain different sounds. Even external feedback processing is possible (e.g. with a VCA for voltage controlled feedback). The feedback control has polarizer function, i.e. the neutral position is at the centre. Left from the centre the feedback signal is subtracted from the input signal, right from the centre it's added (negative/positive feedback). Even for this potentiometer the new version with centre detent is used.

A special feedback can be obtained if one of the mix outputs is used for the feedback function. In this case for each tap the positive or negative feedback share can be adjusted. This leads to multiple peaks and/or notches in the frequency response of the module.

For each tap of the BBD a separate output socket is available. These sockets can be used for changing the feedback loop - as mentioned above -, for voltage controlled mixing of the taps - e.g. with the voltage controlled mixer A-135 or other applications that require access to each single tap.

The A-188-2 uses the same high speed VCO (HSVCO) for the BBD clock as the A-188-1. The clock and consequently the delay time can be controlled manually (delay control) and by the two control voltage inputs CV1 and CV2. The sensitivity of CV1 is approximately 1V/oct. CV2 is equipped with a polarizer (a new type of potentiometers with centre detent). The HSVCO has a clock output available that is normalled to the clock input socket. These sockets can be used to link different BBD modules and to run them with the same clock. But even other applications with frequency dividers (e.g. A-163) or PLL (e.g. A-196) are conceivable. A voltage composed of the manual delay control, CV1 and CV2 is available at the CV out socket, e.g. to control an external clock suppression filter as the A-188-2 is not equipped with such a filter (same as for the A-188-1).
Read more
 1 in stock $214.16
Click for better price!
or call +44 20 7424 1960
quote 755403
Items 1 to 6 of 6 on page 1 of 1

Filter

Saved Searches
Save current search
Release Date
Featured
Close