Search dance music

Notes: Blank panel, 8HP, constructed from anodised aluminium, silver.

Notes: A-100SSB is a combination of power supply and bus board with 8 connectors for A-100 modules, planned for applications with up to 8 modules and a max. current of 380 mA.

- Wide range mains voltage input 100-240V AC / 50-60 Hz
- IEC inlet on board for the connection of a suitable mains cable (a suitable mains cable has to be purchased by the customer locally, it's not included with the A-100SSB)
- Switching supply with +12V/380 mA and -12V/380mA for the operation of A-100 modules up to 380 mA total supply current
- Safety cover at the bottom side (covers all elements that lead mains voltage)
- On board fuse
- 8 bus connectors
- LED displays for +12V, -12V and +5V
- Dimensions: about 270 mm (length) x 55 mm (width) x 35 mm (height)
- Several 3mm holes for mounting the unit on a rear panel or bottom plate

Notes: High quality rotary knob, for use with Doepfer or a wide range of modules. Robust design with indented edges. Grey finish.

Notes: High quality rotary knob, for use with Doepfer or a wide range of modules. Robust design with indented edges. Red finish.

Notes: High quality rotary knob, for use with Doepfer or a wide range of modules. Robust design with indented edges. Green finish.

Notes: High quality rotary knob, for use with Doepfer or a wide range of modules. Robust design with indented edges. Yellow finish.

Notes: High quality rotary knob, for use with Doepfer or a wide range of modules. Robust design with indented edges. Retro style finish.

Notes: Custom ALM patch cables. Small but strong, they are designed for maximum ergonomic post modern wiggling.

- 90cm (Pack of 3 + ALM branded tie)
- Colour: White

Notes: The new, 2nd generation Audio Jacks Board comes pre-installed in every Intellijel 7U case manufactured since early 2019. Because this board is more fully featured than the previous generation, it's available as a stand-alone component for anyone who wishes to update an older 7U case.

You can tell which board you have by looking at the connectors. The new Audio Jacks Board has a large shrouded header flanked by two smaller shrouded headers, flanked by two link connectors at either end. Older boards have only one connector along the bottom edge.

The board holds four Neutrik TRS jacks, each of which can be configured as either an input or an output depending on the modules you connect. This allows you maximum flexibility when configuring your case - whether you wish to use the audio jacks as outputs, inputs, sends & returns; or some combination of these.

The jacks carry different audio signals depending on what you connect to the Audio Jacks Board. Please refer to the manual for more details on the many options available.

Notes: Your Palette case is the ideal solution for your space conscious and portable needs. At about the same size as a small laptop, your Palette fits comfortably on your desktop; in your backpack; at your favourite coffee shop; in your jam space; or pretty much anywhere else you might desire to play. Your imagination is the only limit. With 62hp of rack space, you can piece together powerful but focused mini systems and control surfaces. Intellijel's 1U row and built-in i/o ports add a ton of extra utility to bring the most out of your Eurorack modules. Truly a palette for the sonic artist.

Utilities panel:

- Dual 1:4 buffered multiple
- Two 1/4" balanced audio jacks that can be connected to the Stereo Line Out 1U, Pedal I/O 1U or Mixup
- 1/8" (6.35mm) MIDI Input that can be connected to uMIDI 1U
- USB port that connects to the uMIDI 1U and other future modules
- Rocker switch and barrel plug for power entry

Construction:

- Anodized aluminium
- Aluminium extruded rails with steel threaded inserts
- Rubber feet to protect your desktop
- Rear mounted power supply for maximum module depth

Includes:

- 40W Meanwell AC/DC adapter with right angled connector
- 3FT North American IEC power cable
- 1/8" (6.35mm) TRS to 5-Pin Din MIDI adapter

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Custom wrench for 3.5mm jacks, designed for Bananuts or other slotted round 3.5mm nuts.

Notes: The A-100LC1v is a smaller version of the A-100LC3 with 48 HP of space. It is made out of raw wood, a black coating gives the Eurorack frame a vintage look. The built-in power supply, type A-100SSB, delivers up to 380 mA at +12 V and -12 V as well as 100 mA at +5 V.

The A-100LC1v comes equipped with one 48 HP measuring row for 3U modules. Its power supply features eight connectors for oscillators, filters and so forth. The case is connected to the grid via an IEC power socket.

Notes: Bus board to connect 14 modules

An assembled and tested bus board, 22 sockets, e.g. for customers who want to built their own case and need a bus board for A-100 modules, includes cables for connection to +/-12V power supply (4 wires with flat connectors on both ends, length about 30cm), but no mechanical parts (e.g. screws, spacers, nuts, washers).

In the new version of the A-100 bus board (labeled Version 6 / 2019) boxed pin headers are used which are equipped with a reverse protection (gap for the "nose" of the socket of the bus cable). When the bus cable coming from the module is connected to the boxed header in question the "nose" has to point to the right. The polarity of the cable is correct if the red wire of the bus cable then points to the bottom (to the continuous line labeled"RED WIRE" on the pc board). If this is not the case please do not connect the module to the bus board ! Otherwise both the module and the power supply (A-100PSU3) may be damaged ! In that case please contact the manufacturer of the module and ask for a suitable bus cable with the correct polarity of the connector.

The bus cables of original A-100 modules manufactured by Doepfer are equipped with suitable bus cables since 2012. Only for older A-100 modules manufactured before 2012 it may happen that the polarity of the 16 pin female connector of the bus cable is wrong (nose points to the left when red wire points to the bottom). This is because in the past unboxed pin headers were used and the position of the "nose" did not matter. In such a case please contact Doepfer or one of their dealers and order a suitable bus cable.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod64X Unpowered is 64HP with 2.16" (55mm) of available module depth. No power supply is included, you must supply your means of powering modules with a DIY power supply or a front-facing module such as the Row Power. Two holes on the rear face are plugged with removable plastic plugs, and can be used for DIY applications.

Pods are a perfect way to get started in Eurorack, or add a couple more modules to your monster system!

Made from 100% anodized aluminum, Pods are light, tough and perfect for on-the-go set ups. Mix and match your Pods with desktop synths, effect pedals, drum machines or any musical gear for a flexible modular system. Need to add another module? Just add a Pod! Need to pack light for a live set? Just grab the Pods you need and go!

Basic Features:

64 HP Eurorack modular space
Standard M3 threaded holes
100% lightweight anodized aluminum

Includes:

64HP Pod, black anodized aluminum
M3 x 8mm pan-head screws, stainless steel (20)
Adhesive rubber feet (4)
Unpowered: requires you to provide your own Eurorack power system
Exterior dimensions:
Width: 329.7mm (12.98")
Height: 159.5mm (6.28")
Depth: 57mm (2.24")
Interior dimensions:
Max module depth: 55mm (2.16")
Module width: 64HP
Weight:
0.42 kg = 14.9 oz

Notes: The Pod40X is 40HP with 2.00" (51mm) of available module depth. The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod40 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: The Mini Case offers 40 HP for mounting modules. A power supply is built-in.

208 mm long x 45mm deep.

PLEASE NOTE: Comes with EU 2 pin plug only - UK adapter may be required.

Notes: Blank panel, 4HP, constructed from anodised aluminium, black.

Notes: Blank panel, 8HP, constructed from anodised aluminium, black.

Notes: These cables are designed to interconnect pro audio gear with unbalanced mini phone jacks. They are ideal for use with modular synthesizers and sound modules.

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Connectors: 3.5 mm TS to Same
Conductor: 26 AWG OFC
Shield: 85% OFC Spiral
Quantity: 8 pc

Notes: These cables are designed to interconnect pro audio gear with balanced phone jacks. They are ideal for use with balanced phone patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Connectors: 1/4 in TRS to Same
Conductors: 26 AWG x 2 OFC
Shield: 85% OFC Spiral
Quantity: 8 pc

Notes: Large sized spring reverb tank, Accutronics 9BB2C1B with 3×2 springs and medium decay (1.75 - 3 seconds).

Notes: TPS80W Triple Power Supply - TYPE A

The TPS80W is a high power, super efficient and low noise studio grade power system for your Eurorack Modular. We carefully designed this power supply to perform optimally with even the most demanding, noisy and power hungry modules in your rig.

Notes: Blank panel for Intellijel 1U spaces. Made from high quality brushed aluminium that matches the 1U modules.

These can also be used for DIY purposes if you drill/mill them to fit your own custom circuits.

Comes with 2 screws.

Notes: ***POWER SET FOR EU AND AUSTRALIA 220-230V:
The Pittsburgh Modular Structure 208 and Structure 360 eurorack enclosures use a switching power supply that needs manually set to the correct AC input voltage. The internal switch has already be properly set for 220-230 VAC. This setting works for the EU and Australia or other countries that use 220-230 VAC power.
For use in countries that use 100-120 VAC power, such as North America and Japan, the switch inside the case on the AC/DC regulator needs to be switched to the left. The switch is marked with a Yellow sticker printed with "AC input voltage can be selected by switch. Check input voltage avoiding damage before power on." The switch is located on the side of the enclosure below the arrow.
Please contact Pittsburgh Modular with any questions. service@pittsburghmodular.com***

Structure EP-360 Eurorack Enclosure

Maximum Power for a New Generation -

Beautifully stained hardwood triple row, 360hp powered eurorack travel case with lid. A huge case to house a monster synth. Features include a professional, heavy duty, internal power supply designed to exceed the needs of the most demanding analog and digital eurorack systems.




Everything is New:
With years of research and two case lines under our belt, we decided to start over and produce a line of cases for the next generation of eurorack synthesizers. The eurorack modular ecosystem is expanding faster than ever and manufacturers are constantly pushing eurorack cases and power supplies to the limits. What started as a power supply designed to drive primarily analog synthesizers has transformed into a supply that needs to simultaneously meet the unique demands of sensitive analog circuitry, power hungry digital processors, and ground sensitive user interface modules.

We started with what matters most. Clean power. A lot of it. Up to 3x the amount of clean power available in cases from other brands. Next we turned our focus to the enclosure itself and there was only one goal. Make the case stronger. Our engineers tested countless combinations utilizing different types of wood, joints, adhesives, assembly techniques, and hardware to ensure that Structure cases are as durable as they are beautiful.

With a clean and gorgeous design that promotes creative exploration, the Structure enclosures are our most robust and refined case line yet. With massive amounts of both room and clean power, you can reach completely new heights in your creative performances.






Includes:
Structure EP-360

Power
:
6 Amps of Clean +12v Power

6 Amps of Clean -12v Power

5 Amps of Clean +5v Power

Custom Powered Bus Board with 15 Keyed Eurorack Power Headers Per Row, 45 Power Headers Total

External On-off Rocker Power Switch with LED

Universal IEC Power Connector Works Anywhere

Structure EP-360 Enclosure
:
Hardwood and Steel Construction (No cheap plastic here)

Triple 120hp Rows

Removable Lid

Lid Fits Over Fully Patched System (No need to remove patch cables)

Edge to Edge Rail Design Reduces Gaps Between Modules and the Side of the Case

24 Smooth Sliding Square Nuts Per Rail (Holds up to 72 modules)

Beautifully Hand-Stained Hardwood

Matching Black Steel Hardware Set




Structure EP-360 Dimensions
:
External Depth with lid:9 1/4"
External Depth without Lid: 5 1/2"
External Height: 17"
External Width: 25 1/2"
Internal Depth Above Power Supply: 2 3/4"
Internal Depth Above Bus Board: 3 3/4"
Internal Depth Above Nothing: 4 1/4"

Notes: Desktop Eurorack moduile case 3U - 104HP with power supply on the left side.

Plexiglas side panels 5mm thick.

Aluminium chassis.

6cm deep, but only 4cm deep all along the 5HP of the power supply. Check your modules before!

Tech specs:
- Width : 104HP
- Depth : 6cm
- Depth all along the 5HP of the power supply : 4cm
- Current Consumption : +12V : 2.4A ; -12V : 1.2A ; +5V : 0.5A

Notes: Rack Screws - Tin of 30

These rack screws for Eurorack can be screwed by hand for quick changes, or use a standard screw driver.

Each Special Size M2.5 X 8mm stainless steel screw comes with a black nylon washer in a silver tin.

Notes: These knobs are custom made for AE modular; they fit perfectly on the shafts and can be added to all AE modules, no matter of which generation they are.

As of December 2020, all AE modules will be shipped with these knobs as standard.

Notes: This is a variant of the standard red/black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Notes: This is a variant of the standard red/black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Notes: This is a variant of the standard red / black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Notes: This is a variant of the standard red/black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Please note: This rack does not include the Master or Power module. To connect the case to power you have the following options:

Connect the case to your system via the Hinge Kit 1 or 2 (only for cases newer than 2019)
Connect the case to your system via the Racklink Module (works for all cases)
Install the Master Module
Install the Power Module

Whichever option you decide on, you will also need to order and install 2x Bus Cables, but be careful to order the correct size! Standard Bus Cable for Standard Case size, etc.

Notes: This is a variant of the standard red/black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Please note: This rack does not include the Master or Power module. To connect the case to power you have the following options:

Connect the case to your system via the Hinge Kit 1 or 2 (only for cases newer than 2019)
Connect the case to your system via the Racklink Module (works for all cases)
Install the Master Module
Install the Power Module

Whichever option you decide on, you will also need to order and install 2x Bus Cables, but be careful to order the correct size! Standard Bus Cable for Standard Case size, etc.

Notes: This is a variant of the standard red/black racks for AE modular with wooden front and sides.

Same as with the standard cases, via a joint kit (not included) another case of this width (either one-row or two-row, standard or wooden type) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides, front and back are made of real-wood veneer covered MDF.

Please note: This rack does not include the Master or Power module. To connect the case to power you have the following options:

Connect the case to your system via the Hinge Kit 1 or 2 (only for cases newer than 2019)
Connect the case to your system via the Racklink Module (works for all cases)
Install the Master Module
Install the Power Module

Whichever option you decide on, you will also need to order and install 2x Bus Cables, but be careful to order the correct size! Standard Bus Cable for Standard Case size, etc.

Notes: These knobs are custom made for AE modular; they fit perfectly on the shafts and can be added to all AE modules, no matter of which generation they are.

They are available in four different colors: red, blue, green and yellow.

Notes: These knobs are custom made for AE modular; they fit perfectly on the shafts and can be added to all AE modules, no matter of which generation they are.

They are available in four different colors: red, blue, green and yellow.

Notes: These knobs are custom made for AE modular; they fit perfectly on the shafts and can be added to all AE modules, no matter of which generation they are.

They are available in four different colors: red, blue, green and yellow.

Notes: These knobs are custom made for AE modular; they fit perfectly on the shafts and can be added to all AE modules, no matter of which generation they are.

They are available in four different colors: red, blue, green and yellow.

Notes: Banana cable for modular systems, as used by companies such as Buchla. The length is 12.7 centimeters.

Patch cable with banana plugs.

Length: 12.7 centimeters

Color: Violet

Notes: Banana cable for modular systems, as used by companies such as Buchla. The length is 76,2 centimeters.

Patch cable with banana plugs.

Length: 76,2 centimeters

Color: Blue

Notes: Meng Qi's Char is a unique passive signal multiple, allowing three-way stereo signal multing.

It features a keychain attachment for easy carrying.

Notes: Unique custom design 3.5mm patch cables.

They feature strong, ergonomic barrels which are slim and stubby for max patchability.

Available in various lengths (15, 30, 60, 90 & 120cm) and colours.

Longer 60, 90 & 120 lengths also include ALM cable tie.

Notes: Unique custom design 3.5mm patch cables.

They feature strong, ergonomic barrels which are slim and stubby for max patchability.

Available in various lengths (15, 30, 60, 90 & 120cm) and colours.

Longer 60, 90 & 120 lengths also include ALM cable tie.

Notes: Unique custom design 3.5mm patch cables.

They feature strong, ergonomic barrels which are slim and stubby for max patchability.

Available in various lengths (15, 30, 60, 90 & 120cm) and colours.

Longer 60, 90 & 120 lengths also include ALM cable tie.