Search dance music

Notes: Erica Pico RND is combined LFO/random source module.

It generates sine LFO waves, white noise, S&H CV and some interesting stuff - random triggers and pulse wave with random duty circle; basically, everything, you need, to bring some uncertainty in your modular setup.

The Pico RND comes equipped with five outputs, they emit the following signals:

- Sine waves
- Pulse waves with varying width
- Random triggers
- Sample and hold material
- White noise

The speed of LFO and S&H circuit can be edited using the module's potentiometer (Range: 0.1 Hz to 20 Hz). For synchronizing the Pico RND with other gear, a clock input was implemented.

Notes: Pico DSP is a small brother of the popular stereo effects processor Black Hole DSP. It contains eight algorithms, in detail four delays, two types of reverb, Leslie speaker emulation and an Overdrive/Bitcrusher. Each effect is editable in two parameters. One of them can be modulated using the CV input. Pico DSP features clear, high-resolution sound. Alongside the established standards, it is also possible to generate lots of freaky special effects.

Notes: Erica Synths Pico OUTPUT module is just what you need to monitor your music on headphones and have standardized connection to mixing desks.

Features

Stereo input
High quality headphones amplifier
3,5mm headphones output jack
Headphones volume control
3,5mm stereo line output jack
The 3,5mm stereo output jack in this module allows you to connect the Pico System directly to virtually any speaker system or line input. Even in your car!

With Pico Series we challenged ourselves - can we make ANY superior functionality synth module 3HP wide and affordable? Yes, we can.

Technical specification:

Input level: 10Vptp
Power consumption: +20mA, -7mA
Module width: 3HP
Module depth: 35mm

Notes: Module A-160-5 is a voltage controlled clock multiplier. The incoming clock signal (socket Clock In) is multiplied by a factor that depends upon the control voltage on socket CV In (0...+5V) and the position of the Mode switch. The multiplied clock signal is available at the socket Clock Out. According to the position of the Mode switch different clock multiplying factors are assigned to the control voltage. With 0V CV no clock output is generated. This state is indicated by "all LEDs off". With increasing CV integer factors (left position of the mode switch), power of two factors (middle position) or a mix of both (right position) are obtained. Nine LEDs are used to show the currently selected multiplying factor. In addition two LEDs are used to display the incoming and outgoing clock signal.

A manual control is used to adjust the clock multiplication factor manually without the need of an external control voltage. The voltage generated by this control ("Manual") is normalled to the CV In socket. As long as no plug is inserted into the CV In socket the clock multiplication factor is adjusted by means of the manual control knob and displayed by the LEDs. For dynamic applications (like the ratcheting function described below) the manually generated CV is overwritten by the external CV which has to be fed into the CV In socket.

The module can be used for all kind of clock multiplying applications. One important example is the generation of so-called ratcheting sequences. The band Tangerine Dream is famous for this kind of sequences. A normal sequencer generates only one gate signal per step. A ratcheting sequence may have also more than one gate pulses per step. This function can be obtained by using the A-160-5: one CV output of the sequencer is used to define the number of gate pulses per step. If the control of the step in question is fully CCW the generated CV is 0V and no gate signal is generated (mute of the step). When the control of the step in question is turned clockwise one, two or more gate pulses are generated depending upon the position of the mode switch and the voltage generated by the CV at this step.

Technical note: Due to the nature of clock multiplying it takes a few input clock pulses until the clock output is stable. One has to average a few input clock pulses to generate the multiplied clock output signal. Even when the input clock frequency changes it will take a few cycles until the output clock signal is correct as the module cannot foresee the future of the clock input signal. The generated clock output signal is derived from the last few cycles of the clock input signal. Consequently the module should be driven only by a clock signal with constant or slowly changing frequency.

Notes: MAR is a multichannel dual mixer module for the modular synthesizer. Both mixers are capable of mixing audio, CV and gate signals because they are DC coupled. MAR has two independent 4-channels mixers:

Mixer X: Is a four channel mixer with gain control for each channel. The potentiometers use logarithmic tape to have a good control with audio signals. This mixer features two outputs, the mixer output and its inverted. The output level is shown in the LED.

Mixer Y: Is a four channel mixer with gain control for the sum of the Y channels. If no jack is connected to the input Y1, the output of the Mixer X is normalled to Mixer Y. The potentiometer use logarithmic tape to have a good control with audio signals. This mixer features one output, the sum of the 4 channels. The output level is shown in the LED.

This Mixer can work as two 4-1 Mixer, or 7-1 Mixer with global gain control.

INPUTS:
4 Mixer X inputs.
4 Mixer Y inputs.

OUTPUTS:
Mixer X output.
Inverted Mixer X output.
Mixer Y output.
Mixer X + Mixer Y output.

FAST SPECS:
Dual mixer module for the modular synthesizer - Eurorack.
8 HP - 15mm Depth - Skiff friendly.
Both mixers are capable of mixing audio, CV and gate signals.
Mixer X: 4-channel mixer with gain control for each channel.
Mixer Y: 4-channel mixer with gain control for the sum of the channels.
If no cable connected to Mixer Y input 1, the output of the Mixer X is normalled to Mixer Y.
Can work as two 4-channel mixers, or one 7-channel mixer.
The output level is shown in the LEDs.

Notes: Complex gate and CV generator designed as a trigger source and modulation tool. Based around four sine wave LFOs that mix together and interact to create ever-changing patterns.

Supplier's Notes:
In 2009 John Berndt coined and defined the term Relabi in his essay "Relabi": Patterns of Self-Erasing Pulse, these are his own words: "Relabi, Def.: The experience of a palpably coordinated plurality of events that appears to be cyclical but simultaneously suspends identification of a uniform pattern, preventing a resolved sense of pulse. Relabi therefore seems equally pulsed and unpulsed at the same time. It is an experiential gestalt, a quality of experience, greater than the sum of its parts (it forms a sustained unity in experience, albeit of a new kind)."

He also makes the question: "Why would anyone want this Relabi experience? I maintain that much of what is exciting in musical forms involves an interplay between the setting up and denying of pulse expectations."

Inspired by this idea, ADDAC System developed this module that is both a gate/trigger and cv generator that can be freely used to trigger events or act as a complex modulation source. Four Sine LFOs are internally generated, each has controls for gain, frequency and mute(off). These 4 LFOs are then mixed together to generate what Berndt named the "Relabi Wave" this "wave" becomes a complex bipolar CV source. This i5v bipolar "wave" can be monitored on the 2 dedicated leds and is also available at its own Output.

Make sure to check the User's Guide for indepth description, working behaviour and diagrams.

Tech Specs:
10HP
4cm deep
100mA +12V
40mA -12V

Notes: Gate Expander for Sweet Sixteen mkII.

This is an expander, brings 8 gate inputs for the Sweet Sixteen mkII.

The panel is reversible, so jacks & buttons can be in the left or right side.

The orientation of the 10 pin ribbon cable is marked by the 'do not plug power here!' legend on the PCB, so it could be with the red stripe facing that in both GESS and Sweet Sixteen mkII modules.

Notes: Dual tidal modulator with max, min & mix outs

FranKinksTides is a 18hp dual Tides (based on the Swirls pcb layout) with the max/min circuit from Kinks and some switches for sync, quadrature, pll and fm operation . It can be a double/complex oscillator, a dual function generator or any combination of oscillator, Lfo and Envelope generator with lots of cv control plus some interesting cross-modulation and sync features.

Some improvements in version 1.2:

-Mix output is now buffered, no signal bleeding on single outs.
-Mix pot controls also the balance of the signals sent to the max/min circuit.
-Uni/bi switch now also determines the signal sent to FM1.
-Clock/sync switch has now a center OFF position, no need of plugging a dummy cable in the Clock1 when using Sheeps firmware to avoid ultra fast sound bank changes.
small improvements for DIY:
-Bigger font size on the pcb.
-Parts renumbered for easy DIY.

Original design by Emilie Gillet
Available assembled and DIY (pcb+panel)
+12v
-12v

Notes: 16 trigger ins to play up to 4096 wav files from a micoSD card

Nutella is a eurorack conversion module for the Sparkfun Tsunami Super Wav Trigger.
Features:
-16 trigger in & buttons to play audio files.
-MicroSD card to store up to 4096 wav files in 44.1kHz 16bit.
-32 voices polyphony in mono and 18 in stereo.
-Low latency (8ms typically)
-8 audio outs (modular level)
-Midi in (velocity sensitive, supports MIDI Note-On, Note-Of, Pitch Bend and Program Changes messages, as well as Controller messages for real-time control of sustain, attack and release times and volume.
-Ability to play multiple audio stems in sample-locked sync.
-Can be used as a Wav player and Midi-to-Trigger converter at the same time.
-Trigger ins (and so buttons) can be assigned to various functions (normal, next, previous, random, pause, resume, stop, volume up, volume down, trigger bank up, trigger bank down, synced set, midi bank up, midi bank down)
-Easy configurable by an optional ".ini" file stored in the microSD card, a Tsunami Configurator utility (Windows, Mac and Linux versions available), makes it easy to set options and generate this file.
-Super easy firmware update system via microSD card, no external programmer needed.

30 mA +12V
15 mA -12V
200 mA 5V

Notes: This is a 4 mono channels expansion. Several of these modules can be added to provide more channels. Every channel features:
- Mono input
- Vactrol Gate (plug a CV into the GATE IN to modulate the volume of a channel, just like a classic VCA. When nothing is plugged in the GATE IN, the gate is normalled to fully open)
-SEND A control (switchable PRE/POST, in PRE mode the signal is present regardless to the channel volume control but only if the channel switch is in ON position)
-SEND B control (post-fader)
-PAN control (only affects the master bus)
-VOLUME control (affects the master, cue and POST sends, does not affect PRE-fader send)
-ON/OFF/CUE switch: ON - channel is routed to the master bus
OFF - channel is muted
CUE - channel is routed to the cue bus

13 mA +12V
8 mA -12V

Notes: LED Meter is a handy utility module designed to show audio levels. Three color versions are available:

- green colour with yellow-red peak segments.
- all blue colour
- all yellow colour

There are total 30 led segments, each one roughly corresponds to 1 dB of level, so it is 30 dB of measurement level available with this module.
The module has an input for the signal to be displayed, and its buffered copy is sent to the output for further processing, so no external splitter is needed.
Two trimmers are accessible via holes on the front panel: left trimmer adjusts brightness and right trimmer is used for the level adjustment. So the module can represent full scale signals ranging from 1 V to 12 V.
There is operation mode jumper on the back side. When the jumper is installed - bipolar operation is active, and when the jumper is removed - ordinary audio meter is active.

Dimensions
4 HP
40 mm deep

Current Draw
150 mA +12V
20 mA -12V

Notes: The Erica Synths Envelope Generator 2 is a re-triggerable, looping envelope generator with some unconventional features that are very useful for experimental setups. What sets the Black EG2 apart from other envelope generators is its optional GATE LENGTH setting, which allows for generating full ADSR envelopes even if a short trigger is used at the input. Likewise, in LOOP mode, the module outputs a full ADSR envelope instead of a classical AD envelope. The gate length is both manual and CV controlled, which allows for using this envelope generator in compact modular setups controlled by trigger sequencers only.

SPECS:

Gate input level 3...10V
Envelope amplitude 0...10V
Attack time 0...7,4"
Decay time 0...19"
Sustain level 0...10V
Release time 0...17"
Gate length 0...3,7"
Panel width 8HP
Module depth 25mm
Power consumption 29mA@+12V, 33mA@-12V

LOOP/SINGLE

Select between SINGLE SHOT or LOOP modes. When the internal gate is o , the rise and fall times are set via the A and R knobs. When the internal gate is on, all knobs have an e ect on the envelope shape.

The LED gives visual feedback on the envelope state.
GATE ON
Engage the internal gate and you have a full ADSR envelope in loop mode and with a trigger applied to the trigger input in single mode.

G. LENGTH

Set the internal gate length manually

LENGTH CV

This is the internal gate length CV input.

The CV is added to the gate length potentiometer setting

GATE

This is the GATE input

A / D / S / R

These knobs adjust envelope stage times and sustain level

TRIGGER

This is the TRIGGER input. You can retrigger the envelope and start the attack stage again, even if the gate is still high (see Figure 1).

If you wish to use the envelope generator with an internal gate, patch the incoming trigger signal here. The internal gate is linked to the trigger input, not the gate input.

EG OUT

This is the envelope generator output.

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Inspired by the legendary Moog CP3 mixer, the 713 tweaks the old-school discrete circuits into three stereo inputs and one mono channel, summing to stereo with adjustable feedback and clipping to add character.

Supplier's Notes:
ADDAC713 is the stereo version of ADDAC System's 703 Discrete Mixer.

Inspired by Moog's CP3 mixer, this is a fully discrete analogue mixer and it's not, by any means, your standard breakfast mixer, although it can behave like one.

This is a wolf in sheep's clothing. Despite its harmless looks there's a dark snarly soul behind that panel that wants to take your sounds into a realm of gritty gnarly growls.

This new version was initially thought of as a percussion mixer, with mono inputs and panning, to allow placing percussive voices in the stereo field, while keeping channel 4 in mono for low end sources like a kick drum or Bass. In the development process ADDAC System slightly changed this initial idea, adding stereo inputs for the first 3 channels, but still kept the 4th channel in mono.

All four [GAIN] controls go to extreme levels, the first 3channels also feature [PAN] controls. Feedback is used to overdrive the whole mix. As the control is turned clockwise the sound will be clipped harder until it goes completely off, this happens as feedback is increased the audio bias reference also moves up, at extreme levels it offsets the whole signal upwards until it completely goes above the top rail clipping the whole signal hence the resulting gate effect.

The [MASTER OUTPUT] sets the overall output gain of the mixer, the two leds monitor the audio output signal. The Soft clipping switch engages an anti-click circuit which adds a low pass before the output, the switch allows 3 states: Soft low pass / Off / Hard low pass.

Features:

Three channels with stereo inputs, gain and pan knob
One channel with mono input and gainknob
Feedback/gate knob
Master output volume knob
Soft clipping switch
Two Led Monitors for Left and Right channels

Tech Specs:

8HP
4cm deep
80mA +12V
80mA -12V

Notes: Great value from 4ms's twist on the Stereo Triggered Sampler module, this time capable of playing and manipulating stereo or mono WAV files from an SD card.

Supplier's Notes:
The Sampler is a variation of the Stereo Triggered Sampler.

Record, play and loop stereo .wav files with an SD Card. Includes the same 2022 Sampler Pack from the Stereo Triggered Sampler.

Features:

The Sampler plays stereo or mono .wav files from an SD Card. Samples are arranged into banks by placing .wav files into folders (each folder is a bank). A maximum of 10 samples can be loaded in a bank. There is a maximum of 60 banks (600 samples maximum total).
Sample files are limited to 4GB each, which is over 6 hours at 44k/16b/stereo.

Hundreds of samples included on microSD card
Extremely quiet, low noise and low jitter design
Stereo or Mono output

A knob and CV jack selects the Sample to play, and the Start Position knob and CV jack control where in the sample playback will begin. The Length knob and CV jack determine how much of the sample is played back: from tiny grains, to percussive hits, to longer loops... or just the entire file.

Pressing Play or firing a trigger into the Play Trig jack will play the sample. Holding the Play button down for a second will toggle looping.

There's also a Reverse button and jack for backwards playback, and an End Out jack for synchronizing loops, or cascading sample playback with other events.

To record samples, hold Play and Reverse for two seconds. Press Play again or fire a trigger into the Play/Rec Trig jack to start and stop recording. Each recording will create a new stereo 48kHz 24bit .wav file in the current bank's folder. Recordings can be as long as your card has the capacity for: a 256GB card is 18 days of continuous recording (432.9 hours). Audio data is split into maximum 4GB wav files on the microSD card.

Play button/trigger jack: Tapping the button or receiving a trigger starts/re-starts the sample
Sample CV/knob: select which sample within the channel's bank
Pitch CV and Pitch knob: playback pitch (-10 to +4 octave range)
Start Pos CV/knob: position in the sample to begin playback (loop start point)
Length CV/knob: playback time (loop end point)
Length knob at max: entire file is played
Length knob 50%-99%: 200ms - 5s of the sample is played (beginning at the Start Position)
Length knob <50%: Percussive decay envelope is applied to the playback (attack-only envelope if playing Reverse)
Length <1%: Tiny grains are played (can be used to sweep through sample file data manually)
Reverse button/jack: toggles forward/backwards
Bank button: selects channel's bank
Reverse + Start Pos button/knob combo allows for setting volume of playback
Maximum file size for playback: 4GB per file (6.7 hours per file at 44.1kHz/16b/stereo)
microSD Card is hot-swappable when Busy light is off: no power-down required to change cards.
Samples that are pre-loaded into memory can continue playing while card is swapped.

File Organization:

Using a computer, the intuitive automatic bank loading features make dragging and dropping your entire sample library a snap. No files need to be renamed. Just create folders and put up to 10 samples in each. If you want a folder to be associated with a particular colour of the Bank button, name the folder a colour name (such as "Blue - Loops").

Ships with a high-speed 16GB microSD card, loaded with hundreds of samples created for 4ms, from musicians such as Richard Devine, Wobbly, Moor Mother, Robert Aiki Aubrey Lowe, Joseph Pailo, Russell E.L. Butler, Hugo Paris & Marc Kate, Paul Barker, Baseck, Animal Collective, Cristian Vogel, Jay E, Marcus Fischer, Chris Carter, Daedelus, Nero Bellum, Anna Sitko, Thomas Fang, Bogdan Raczynski, and more (Sample List)

Intuitive bank/colour organization system; no need to rename your wav files
Record new samples directly to a bank with the Record Input jacks...
... or drag your folders of sound files onto the microSD card, and each folder will become a bank.
Folders starting with a colour name will be loaded into that colour bank
Example "Blue - Frooty Loops" will load into the Blue bank
Sub-folders are ignored, only folders in the root directory are scanned for wav files
Works best with UHS Speed Class 3 cards with |3| symbol printed on the card

Specs:

Electrical and Mechanical Specifications:
Module Size:
16 HP Eurorack format module
10-pin Eurorack power header
1.3" (33mm) maximum depth with power cable
Power consumption:
+12V: 135mA
-12V: 41mA
+5V rail: not used
Connect red stripe of power cable towards the bottom of the module, which is marked with a white stripe and the words -12V and POWER
Audio Inputs:
20Hz to 10kHz (+/-0.1dB); -6dB rolloff @ 20kHz
21V peak-to-peak maximum before clipping
Audio Outputs:
0Hz (DC) to 22kHz with maximum -1.8dB difference between file data and output
+10.5V to -10.5V maximum output
Trigger inputs:
Latency: 0.7us typical

Included with the Sampler:
16GB micro SD card (class 10)
SD adaptor
10-to-16 pin power cable
M3 Knurlie screws

Notes: Pan and cross fade up to three signals with AJH's versatile Triple Cross. Four different modes allow you to set up the three channels in numerous ways, for both audio and CV processing.

Supplier's Notes:
The Tone Science Triple Cross module is a design collaboration between electronic musician/composer Ian Boddy and AJH Synth.

It features three independant cross fader and panner channels, and it can be used with both audio and CV signals. Each of the channels can be configured in one of four different ways:

1) One In, One out Linear VCA

2) Two in, One out crossfader

3) One in, Two out panner,

4) Two in, Two out cross fader & reversing panner combined.

Audio rate modulation can also be used on the CV inputs to create Ring modulation and Cross modulation type sounds. Each channel has a dedicated Fade control, CV input, and CV Level attenuverter. These can be used together to bias incoming CV signals.

The L1 and L2 outputs from channels 1 and 2 are normalised to channel 3's inputs, which also have their own level controls to balance incoming signals. This allows very interesting, complex fading and panning between four different input sources, to either Mono or Stereo outputs..

The Triple Cross is very versatile, yet relatively simple to understand and use. However, as they say "knowledge is power", so do spend a little time reading about how to configure the channels in the four different modes, and how to combine all three channels together to create a super-powerful Four to Two to One cross fader.
Each of the three channels can be configured in four different ways, and all three can be used simultaneously. They do not all have to be in the same mode, so we could for example use channel 1 as a cross fader, channel 2 as a Panner for completely different signals, and channel 3 as a Linear VCA, again for different signals.

Specifications

Effective CV Range for CV-1, CV-2 and CV-3 is 0 to +5V with attenuverter fully clockwise or 0 to -5V with attenuverter fully anticlockwise.
Maximum permissible CV Range for CV-1, CV-2 and CV-3 is -12 to +12V
IN 1A to IN 3B Input levels -5V to +5V, levels up to +/-10V are possible however some clipping may occur.
Module Width: 14hp
Module Depth: 26mm (Including power lead)
Current Usage: 80mA Positive, 72mA Negative

Notes: The Tone Science Triple Cross module is a design collaboration between electronic musician/composer Ian Boddy and AJH Synth.

It features three independant cross fader and panner channels, and it can be used with both audio and CV signals. Each of the channels can be configured in one of four different ways:

1) One In, One out Linear VCA

2) Two in, One out crossfader

3) One in, Two out panner,

4) Two in, Two out cross fader & reversing panner combined.

Audio rate modulation can also be used on the CV inputs to create Ring modulation and Cross modulation type sounds. Each channel has a dedicated Fade control, CV input, and CV Level attenuverter. These can be used together to bias incoming CV signals.

The L1 and L2 outputs from channels 1 and 2 are normalised to channel 3's inputs, which also have their own level controls to balance incoming signals. This allows very interesting, complex fading and panning between four different input sources, to either Mono or Stereo outputs..

The Triple Cross is very versatile, yet relatively simple to understand and use. However, as they say "knowledge is power", so do spend a little time reading about how to configure the channels in the four different modes, and how to combine all three channels together to create a super-powerful Four to Two to One cross fader.
Each of the three channels can be configured in four different ways, and all three can be used simultaneously. They do not all have to be in the same mode, so we could for example use channel 1 as a cross fader, channel 2 as a Panner for completely different signals, and channel 3 as a Linear VCA, again for different signals.

Specifications

Effective CV Range for CV-1, CV-2 and CV-3 is 0 to +5V with attenuverter fully clockwise or 0 to -5V with attenuverter fully anticlockwise.
Maximum permissible CV Range for CV-1, CV-2 and CV-3 is -12 to +12V
IN 1A to IN 3B Input levels -5V to +5V, levels up to +/-10V are possible however some clipping may occur.
Module Width: 14hp
Module Depth: 26mm (Including power lead)
Current Usage: 80mA Positive, 72mA Negative

Notes: Designed to be a highly customizable connection matrix, 3DVCA packs a boat load of utility into a small 6HP package. Four VCAs share the three macro controls: X, Y, and Z. As a group, they shape incoming and outgoing signals and emulate the coordinates of a point in 3 dimensional space. This allow the VCAs to work together in a mono, stereo, or quad configuration and accomplish a variety of mixing, crossfading, and panning functions.

3DVCA is designed to be used in the following functions:

Quad monophonic crossfader
Dual stereo crossfader
Stereo balancer
Stereo VCA
Mono to stereo panner
Unity mixer with up to eight inputs
Quadraphonic panner

Each output has a dedicated SUM input which allows an external signal to be automatically mixed into the output signal. This allows 3DVCA to daisy chain both with other mixers and other 3DVCAs. For example, you can create a full mono, stereo, or quadraphonic mix by plugging the output of each 3DVCA into the sum inputs of the next 3DVCA in the chain. Using this method, a set of 3DVCAs can create a fully voltage controlled and decentralized mixer which ties together anything from a small skiff to a monster synth.

When 3DVCA works as a crossfader or panner, the X and Y parameters follow an equal-power curve that keep output signals at the same volume no matter how many inputs are mixed together. This is in contrast to the Z parameter which follows a linear curve to always behave predictably with external modulation sources. All inputs are fully DC coupled in order to work with modulation speed signals as well as static DC voltage sequences; this means that 3DVCA can handle any sort of signal that you throw at it. All op amps in the device employ rail-to-rail inputs and outputs to enable the largest headroom when mixing many different signals together.

Whether you need to maximize your mixing functionality in the smallest possible footprint or have the most control over every aspect of your system, 3DVCA provides a ton of functionality in any system. Enter a higher dimension of sound with the Mystic Circuits 3DVCA.

Dimensions
6 HP
30 mm deep

Current Draw
45 mA +12V
45 mA -12V

Notes: A fresh take on granular processing with this stereo DSP module. Grain delay, texturising and freezing with plenty of hands-on control and modulation via CV, gates and triggers. Versatile.

Supplier's Notes:
Melotus Versio is a stereo texturizer that uses granular processing to transform and reshape sound.

Designed to be played by hand or manipulated within a patch, Melotus is everything from a grain delay to a completely transformative texturizer with grain control and manipulation of triggering, direction, and randomness.

Filter audio with a lowpass/highpass combo filter that adds haunting shimmers and subharmonics. Freeze grains by hand or with triggers and gates, or clock them to create rhythmic effects.

Plus, Melotus Versio is part of the Versio DSP platform: transform it into a completely different effect by loading a growing number of alternate firmwares, completely free - or develop your own firmware with our open-source documentation.

Notes: 8-input, 8-output sequential/addressable switch with manual, trigger, and CV control, plus three grouping options, multiple switching directions, and randomization.

Vice Virga is an 8-input, 8-output sequential/addressable switch with a plethora of features and extensive patchability. Vice Virga can be configured as a single 8-channel switch, two 4-channel switches, or four 2-channel switches. Equal parts automated patch arranger and performance tool, Vice Virga has loads of switching control options. Whether you want to chain sequencers, swap outputs on an oscillator, remix a trigger pattern, or mix up every connection in a patch just to see what happens, Vice Virga can do it!

Features:

Size and power:
8HP Eurorack
+12v: 40mA
-12v: 20mA
Vice i from Latin for "alternately"

Virga i from Latin for "switch"

"Alternating Switch"

Notes: This module offers a four-quadrant-control for CVs via its joystick.

The module can act either as CV source at its four outputs, or as four-quadrant attenuator for the CV inputs. Beyond this, a mix of the input CVs according to the joystick position is provided separately.

Another feature is a gate output that is controlled by pressing the joystick handle.

The joystick remains in each position - there is no automatic "return to centre".

The JOYSTICK module can operate in two different modes:

Quadrants independent: In this mode, all outputs are zero when the joystick is in centre position
Overlapped: In this mode, each quadrant output fades from full to zero over the whole range to the opposite corner.

Together with a quad VCA / mixer (available soon from tangible waves) you can use the JOYSTICK also for mixing/blending four independent audio sources.

Notes: The MIXCONSOLE JACKOUT is an extension for the MIXCONSOLE with 1/4" (6.5mm) jack sockets for master left/right output and for the FX send and returns - all via mono sockets (unbalanced). This avoids the need for separate adapter cables.

The module is connected via a small internal connection cable to the right of the MIXCONSOLE or as neighbour of the MIXCONSOLE XLROUT module.

Notes: The MIXCONSOLE XLROUT module is an extension of the MIXCONSOLE and makes the master outputs available as two balanced XLR sockets.

The module is connected via a small internal connection cable to the right of the MIXCONSOLE or as neighbour of the MIXCONSOLE JACKOUT module.

Notes: Mix up to four stereo channels in just 4hp, or chain multiple modules together to add channels. Inputs are normalled for mono operation. Simple, compact and high quality at a reasonable price.

Supplier's Notes:
4xSt.Mixer is 4 HP quad stereo mixer.

Right inputs are normalled to Left inputs for easy mono operation

Several 4xSt.Mixers can be chained together or with other HN stereo modules via sockets on the back side

65 mA +12V
50 mA -12V
35 mm deep

Notes: Two Of Cups - include samples in your live set. Two of them at once with a wide variety of CV-able features. Simply load one of 8 (!) banks each containing up to 24 samples for each of the two voices and off you go (unlock this feature with firmware 1.1!). Needless to say you can change the samples under CV and if needed - you can set up the trigger delay for each voice because that boy plays its sample so instantly and sample accurate with the with lightning speed. Breathe life and fresh sounds into your setup with a small footprint (6 HP) you would normally need to carry around a gazillion of gear to reproduce the sonic capabilities. Alternatively, use it the boring way and simply play drum one-shots off it.

2 voice intuitive sample player each containing 24 samples and organized in 8 banks

Zero-latency sample playback - directly from micro SD card

Factory sound-bank by Julia Bondar

On-board envelope generator decay control, pitch control with 1V/Oct input and sample selection control with meta cv input

Arbitrary sample rate: 8, 16 and 24 bit samples with 12 bit output bitrate

Power consumption:

125 mA +12V
20 mA -12V
0 mA 5V

Dimensions:

6 HP
30 mm deep

Notes: Wonderland is an 8×8 active patchbay/matrix mixer/switcher for both audio and control voltages. It features:

8 inputs (1 through to 8), each with micro-attenuators (which can be set with a small screwdriver)
8 buffered inverted outputs (A through to H) which are 180o out of phase with the inputs
8 buffered normal outputs (A through to H) which are in phase with the inputs
A switch matrix of 64 push on/push off switches
Any of the 8 inputs can be patched to any of the 8 outputs simply by pressing the corresponding switches. A patched signal will appear at both normal and inverted outputs simultaneously.

A single input can be patched to a single output. A single input can be patched to multiple outputs. Multiple inputs can be patched to a single output. Multiple inputs can be patched to multiple outputs.

Each input features a micro-attenuator which can be set with a small screwdriver. This space saving feature allows you to reduce the volume of an incoming signal without having to resort to external attenuators. If you add many inputs to one output you will of course cause clipping (which may or may not be desirable!), the micro-attenuators are your on-board way around this. I find it useful to leave the micro-attenuators set to 50% (which is how they come pre-set at delivery). Of course, their size is a little bit of a compromise, but they are a useful feature nonetheless. Wonderland’s sister module Looking Glass includes full size input attenuators as well as LED status indicators.

Product Specifications
12V draw
30mA

5V draw
0mA

-12V draw
31mA

Depth
35mm

Width
18HP

Notes: Expander module adds four more assignable CV inputs to Squid Salmple for advanced modulation and sample manipulation. A must for all Squid Salmple owners.

Supplier's Notes:
AXON-1 is a 4HP expander module for the SQUID SALMPLE that provides 4 additional freely assignable CV inputs.

The addition of AXON-1 brings Squid's total number of CV inputs to 7, greatly increasing the possibilities for vast modular sample manipulation.

Each modulation assignment includes digital attenuation and offset and behaves just like Squid's 3 built in CV inputs.

AXON-1 requires firmware 166 or later installed on the Squid Salmple to function!

Notes: ADDAC809 is a dynamic CV operated I/O router that allows one source (Audio or CV) to be routed through 2 different chains (of one or more modules) before being sent to an output.
Six routing patterns are allowed:

1. IN > OUT
2. IN > CHAIN A > OUT
3. IN > CHAIN B > OUT
4. IN > CHAIN A > CHAIN B > OUT
5. IN > CHAIN B > CHAIN A > OUT
6. IN > > OUT
A practical example is to have an audio source, a delay and a looper.
And the question: should the delay be placed before or after the looper? Sometimes you may need the delay to be before the looper as you may want to sample the audio with the delay or sample the pure audio source and apply the delay afterwards.
This small utility module solves this issue on the fly without having to repatch anything.

INPUTS & OUTPUTS

TO CHAIN B: Connect to your Chain B input
FROM CHAIN B: Connect to your Chain B output
TO CHAIN A: Connect to your Chain A input
FROM CHAIN A: Connect to your Chain A output
INPUT: Connect to your Input Source
OUTPUT: Connect to your Output Source

ROUTING PATTERNS

There are 2 ways to address the six routing patterns:

Buttons: using the frontpanel push buttons and/or dedicated trigger inputs to latch between 2 states.
BYPASS: Chooses between Pattern 1 and any other pattern
PARALLEL: Chooses between Pattern 6 and any other pattern
ORDER: Chooses the order A before B or B before A
DUAL/SINGLE: Chooses to use a Dual (A>B or B>A) or Single chain (A or B)
CV: The dedicated CV input expects a 0 to +5v input and allows to jump to the precise routing pattern using a specific voltage interval in increments of approx. 0.83V:

Pattern 1: 0v to 0.83v
Pattern 2: 0.83v to 1.66v
Pattern 3: 1.66v to 2.5v
Pattern 4: 2.5v to 3.33V
Pattern 5: 3.33v to 4.16V
Pattern 6: 4.16v to 5V

Tech Specs:

Width: 12 HP
Depth: 55mm
Current: 80mA +12V / 30mA -12V

Notes: Looking Glass is an 5 x 5 active patchbay/matrix mixer/switcher for both audio and control voltages. It features:

5 inputs (1 through to 5), each with attenuators
5 inverted outputs (A through to E) which are 180o out of phase with the inputs
5 normal outputs (A through to E) which are in phase with the inputs
A switch matrix of 25 push on/push off switches and LED status indicators
Any of the 5 inputs can be patched to any of the 5 outputs simply by pressing the corresponding switches. A patched signal will appear at both normal and inverted outputs simultaneously.

A single input can be patched to a single output. A single input can be patched to multiple outputs. Multiple inputs can be patched to a single output. Multiple inputs can be patched to multiple outputs.

The attenuators allow you to reduce the volume of an incoming signal. If you add many inputs to one output you will of course cause clipping (which may or may not be desirable!), the attenuators are your on-board way around this.

Specifications:

12V draw: 30mA
5V draw: 0mA
-12V draw: 31mA
Depth: 35mm
Width: 18HP

Notes: Virt Iter Legio is a three-algorithm stereo oscillator with stereo phase modulation inputs and a vintage-inspired chorus. Love the NE oscillators on the Arturia MicroFreak or the Virt Vereor plugin? Just need it in Eurorack? Virt Iter Legio is the module for you.

Its simple interface and unique, immersive sound make it a staple for any style of sound design. Use the hard sync input to add an aggressive edge to sounds when synced to another oscillator, or try patching VIL's left and right phase-modulation inputs independently for even further sonic exploration in the stereo field. Turn on the beautiful, wide chorus and you'll have an endless supply of sounds like you've never heard.

Notes: Librae Legio is a dynamics processor designed to take a whole patch to the next level. Compression, expansion, limiting, noise gating, and two styles of gentle distortion: Librae is the perfect tool to bring your mix together. And while it can do extreme limiting and really squash your sounds together, Noise Engineering developed it with transparency in mind - whether you want to hard-limit your techno mix or gently bring the sounds in your ambient patch together, Librae is the end-of-chain dynamics processor you've been looking for.

Notes: Updated expander module for the Moskwa II sequencer. The Ostankino adds additional connectivity to the Moskwa II, allowing CV control of most parameters, plus extra outputs.

Supplier's Notes:
Ostankino II expander adds CV inputs for many Moskwa II functions, as well as a transpose input, clock out and individual gate/bit outputs for each step.

Notes: This long-awaited FM voice module from Jomox is a self-contained synth in Eurorack format, patchable and compatible with other modules but capable of creating eight-voice polyphonic patches all on its own. Vastly powerful.

Supplier's Notes:
The Mod FM is a completely self-contained 8 voice FM synth in eurorack format, which can create powerful sounds out of the box without lacking the commonly provided CV modulation possibilities.

It provides 4 Operators and 2 LFOs/VCOs per voice. Additionally it has 2 analogue filters and analogue VCAs per voice which apply analogue warmth and depth to the Mod FM, although the FM engine is digital of course.

Each voice has own CV/Gate inputs and an individual output. There is a mix output which separates even and odd voices. Here you can mix internal effects like delay and reverb to the stereo output signal.

Next to the CV/Gate control, the Mod FM has Midi in and out in TRS type A format and a USB C connector which handles Midi too.

Even without diving too much into complicated modular setups you can create extremely good sounding and metallic FM sounds, snappy bases but also soft and deep sounding analogue style sounds.

Furthermore, the Mod FM offers a variety of external cv modulations in order to e.g. modulate each operator individually or control the FM envelopes.

The Mod FM is fully multitimbral, i.e. each voice can play an own sound in Multi Mode which gets stored as a complete multi set (not only vectorized). That is, you can copy a single sound to the desired multi, but editings made on that particular multi get stored along with the multi set.

Hence, we have the biggest advantage of the hybrid approach:

Modular is great but can be very complex, and you might be trapped in a system where you never reach again the desired sound of the latest session. Storability certainly helps.

The different sections in more detail:

Matrix FM:

4 operators are arranged in a matrix, in which every operator (= sine oscillator) can be modulated by each one of the other three.

The 16 endless potentiometers of the matrix adjust the modulation amount (FM amt) and the base frequency of the operators.

For each operator you can change the base frequency by the diagonal knobs.

There are several overtone modes that determine if one operator is controlled by the keynote (or CV) = base operator, or if it's locked in as overtone (= overtone operator) to the assigned base operator. For the base operator, the number resembles xxx semitones added to the keynote.

For the overtone operator, the adjusted number is the xxx = Nth overtone or harmonics to the base operator frequency.

The locked overtone operator tracks the base operator and is still able to modulate and being modulated.

Each operator has an ADSR envelope. This envelope can also be used to frequency-modulate the operator.

Algorithm:

The algorithms from the known FM synthesis are actually special cases to the whole matrix.

Because it gets pretty quickly uncontrollable if you turn all the knobs because of the feedbacks, Jomox have decided to implement the algorithms. There are 26 algorithms, that are derived from the DX9 with its 4 operators.

At this menu it's even possible to change the frequency mode of each operator to a fixed frequency that is edited in single Hz and which does not follow the keynote, but only modulation. That makes sense for e.g. percussive sounds.

LFO/VCO:

Each voice has 2 LFOs which can modulate either the frequency (FM) or the amplitude (AM) of an operator. Every LFO addresses 64 different wave forms that are displayed in the right OLED display.

There is another feature: each LFO can be switched into a VCO that covers the whole audio range. You can even mix it into the signal chain and it tracks to the keynote. The former LFO rate parameter turns into a detune parameter. That is, you can create classic sounding rectangle/sawtooth analogue basses or string pads - and much more of course.

Filter:

Each voice contains an analogue filter which is build up with the chip SSI2140 from Sound Semiconductor, which is an improved modern version of the old SSM2040, designed by Dave Rossum, and which had been used in Oberheim synths and the early SCI Prophet-5.

The filter has a classic 24dB output and a 12dB state-variable multimode-filter. The three basic characteristic outputs LP/BP/HP can be cross-faded continuously with one parameter called shape.

Both filter outputs 24dB/12dB can be mixed independently.

The ADSR for the filter is fast and cuts in very quick and directly, the resonance is well adjustable.

The filter section contains an own LFO for the cutoff which is independent from the digital sound engine and has also 64 waveforms.

The VCA is a fast transistor-VCA which is important for snappy sounds. The same transistor-VCA is used in all Jomox drum products. Therefore the ModFM can be used as a rich source for technoid drums and percussions of any kind.

Notes: The DIODEFILTER is an adaption of the well-known diode ladder filter that became most popular by Roland's TB-303 bassline. And here it is for the AE modular!

Notes: DRONX is a special mixer designed especially for the DRONE38 module; if has 6 input channels (so you can connect two DRONE38 modules) and offers some sound processing capabilities: A tone control with bass and treble control, a distortion, and finally a dual delay with different algorithms. Two insert points allow to add up to two more audio effects to the internal signal chain. Together with the DRONE38 module(s) you get a quite nice drone synth for dense, dark soundscapes.

Of course, it can be used with any other sound sources!

Notes: The module was named Kuzmin Filter in the past as a tribute to the developer of the Polivoks, Vladimir Kuzmin. For certain reasons, the module will now be called GRUNGE Filter (due to the sound), with the circuitry remaining unchanged.

The Polivoks was a Russian synth that was produced between 1982 and 1990.This module is the AE version of the filter that gave the Polivoks a unique, rough sound.

Beyond the basic design, this filter offers some additional features:

Two different resonance characteristics, hard and soft
An FM function, that adds the input signal to the modulation of the filter
An optional overdrive for the output, making the sound even more rough and untamed.

Notes: Unique, vintage reverb sound.

The SPRINGREVERB module brings the unique sound of this quite old (introduced in the 60's) technique for creating reverbs to the AE modular.

The reverb works by sending the audio signal to a set of 3 springs; at the other end of the springs the sound is picked up by a transducer, converting the mechanical movement of the springs back into an electrical signal. When the audio signal arrives at the end of the springs, the waves are reflected several times; these reflections create the reverb sound.

The spring "tank" (a metal box containing the springs and transducers, size approx. 24 x 9 x 3.5 cm) is connected externally by a cable.

The product contains all components: The module itself, the spring tank and the connection cable.

Note: The sound of a spring reverb is quite unique and has a strong vintage character; if you are looking for a more "clean", natural sounding reverb please take a look at the MULTIFX module.

Notes: With the STOMP-IO module, you can integrate guitar effect pedals and similar devices into your AE modular system! For output (send) and input (return) return there is a mono minijack socket; two minijack to 1/4" socket adapters are included as effect pedals usually work with the latter ones. Send and return levels can be controlled with separate knobs.

Notes: XMIX is a swiss knife for signal mixing and attenuating, offering four(!) mixers and two attenuators in a 1U module. It is designed especially with very small AE systems in mind.

You get:

A three channel mixer "A" with knobs
a passive mixer "B" with four channels
two four-channel mixers "C" and "D" with full level / one-third-level inputs
two attenuators with seven different attenuation levels

All mixers can be used / switched for audio and CV signals.

Notes: The Cali oscillator is a new and improved version of the classic Buchla 258 wave shaping oscillator with an additional pulse width modulated output. The oscillator features the classic Sine to Square and Sine to Saw wave shaping with dedicated CV control. The Cali Oscillator differs from previous versions of the 258 in that it has a 3-way position switch rather than 2-way. This new middle position features a bonus waveform that will shape from a pulse into a kind of triangular trapezoid shape. The shaping control is more unpredictable in this middle position and the switch reacts to body contact when the wave shape is set low - it can be thought of as an extra bonus waveform, great for producing glitchy sounds! There are dedicated inputs for linear and exponential FM and the Cali also adds a Pulse output with it's own width control and PWM CV input. The behaviour of the pulse output can be affected by the position of the waveform switch and wave shape control. The module features Coarse and Fine frequency controls and an LFO mode, LFO range is accessed via an LED pushbutton that also acts as the LFO speed indicator - the button will light up when the waveform moves through its positive cycle. Because the wave shape modulation is independent of pitch this oscillator is very useful for creating complex timbres whilst retaining musical pitch.

Features

Sine to saw/square waveform output with cv over wave shaping

Pulse output with voltage controlled PWM

Linear FM with attenuator

Logarithmic FM with attenuator

Bonus 'trapezoid' output

Coarse & fine controls with LFO mode

Includes power supply isolation on frequency controls


Width: 12 HP
Depth: 22mm

Power
+12V = 37mA
-12V = 34mA

Notes: Gorgeous vintage-style through-zero FM here, featuring five simultaneous waveform outputs, pulse width modulation, soft sync and a dedicated LFO mode.

Supplier's notes:
The EN129 Thru Zero Oscillator is an all analogue triangle-core VCO specialising in frequency modulation. Analogue through-zero FM modulation produces a wide array of timbres particularly useful for bell like or percussive sounds. Through zero linear frequency modulation can be precisely dialled in thanks to a dedicated CV input attenuator and through zero offset control. Logarithmic FM is also available via it's own dedicated input with attenuator and both FM inputs have an LED to indicate incoming voltages. Simultaneous analogue wave outputs include: Sine, Triangle, Sawtooth, Square and Pulse wave with Pulse Width Modulation. The PWM control goes to zero at either end of it's range, which is very useful for creating rhythmic sounds with voltage control. Furthermore the PWM control doubles up as wave shape modulation for the Sawtooth wave - gradually altering the waveform until it shifts half a cycle. The EN129 features Coarse and Fine frequency controls as well as an LFO mode. LFO range is accessed via an LED pushbutton that also acts as the LFO speed indicator - the button will light up when the waveform moves through its positive cycle. A new addition of a Soft Sync Input allows the phase of the oscillator to be controlled by an external oscillator for an even greater range of timbres.

The EN129 is based on the pioneering work by Douglas Kraul and Bernie Hutchins. You can read the original Electronotes article from 1981 that the design is based upon here.

Features:

Soft Sync Input
Thru Zero Linear FM
Logarithmic FM
Zero to Zero PWM
Sawtooth Wave Shape Modulation
Simultaneous Outputs for: Sine, Triangle, Saw, Pulse & Square
Coarse & Fine Controls with LFO Mode
Includes Power Supply Isolation on Frequency Controls
Power consumption: 51mA at +12V and 47mA at -12V

Depth: 22mm

HP : 12

Notes: The Dannysound Dynamics is a compressor / expander originally designed to process drums but, like most processing devices, it can be used for a wide variety of applications.

The module comprises of:

Compressor / Expander
Sub Bass Enhancer
3 Band Inductor-based EQ
Harmonic Exciter

The compressor / expander section uses a discrete transistor-based circuit that allows for soft clipping when overdriven.

The envelope detector is known as a feedforward type of circuit; taking its input from the signal before it goes to the compressor rather than after. This type of circuit is known for having fast attack times.

The Sub Bass enhancer has its own compression circuit that "ducks" the initial transient. This allows the sub bass to be increased without distortion on the transient peaks, increasing the overall level.

There is a MIX control to allow the unprocessed signal to be mixed back in with the processed signal.

The 3 band EQ is an inductor based LCR design. After Dannysound tryed out various EQ topologies, this was the design that sounded the nicest. When overdriven it gives a nice "bite" to the sound, and it has a certain characterful charm that's hard to put into words. The controls have a response that are subtle to begin with and get more pronounced as the controls are increased.

The Harmonic Exciter adds a little distortion to the high frequencies, which bring out the sparkle of cymbals or the snap snare drums. The operating bandwidth can be switched between Low (snare drum snap) or High (Cymbals sparkle).

There are inputs for side chaining and control with an external envelope as well as an envelope out to make the envelope detector output available to drive other modules.

It also features separate inputs and outputs for the Compressor / Expander and EQ sections, so they could be used as 2 separate modules.

Features:

Compressor/ Expander
Sub Bass Enhancer
3 Band Inductor-Based EQ
Harmonic Exciter
Envelope In/Out
Sidechain Input
Seperate In/Out for Compressor, Expander and EQ-Section
Power consumption: 85mA at +12V and 61mA at -12V

Depth: 25mm

HP : 12

Notes: The updated "Skiff friendly" design of the mml filter now features bipolar "Attenu-verters" for the cv controls as well as an all new red mode!

This new mode activates a feedback distortion circuit capable of actually changing the pitch of the notes coming in to the filter in a musical way that adds instant variety to acid basslines, creates weird and strange alterations to drones or adds some nice overdriven distortion to whatever goes into it!

The multi-mode ladder (mml) filter is based on the classic transistor ladder low pass filter by dr. Robert a. Moog. This filter updates the classic 4-pole ladder design to provide band pass and high pass filter responses as well as the traditional low pass filter. There are 2 bipolar controls with attenu-verters for the cut-off frequency plus a cv input for the resonance.

The core of the circuit features a fully discrete transistor design with an op-amp buffered output, this allows soft saturation of the input signal to get the classic overdriven tones of the ladder filter. A bass compensation circuit has been included to retain the bass response in low pass mode when the resonance is increased. The bass compensation also helps to improve the response of the high pass filter.

The red mode is activated/de-activated by holding the mode button for 0.3s. In this mode the filter cut-off, input volume and resonance all interact and the effect is to produce alterations to the incoming frequencies. The pitches of the audio coming into the filter also affect the alterations as well selecting between low pass, band pass and high pass filter modes whilst in red mode.

Features

Low pass, band pass and high pass modes.
Red mode feedback distortion.
CV controlled resonance.
Added low frequency compensation.
Soft saturation of input.
2 x bipolar attenuverter CV inputs.

Width: 6 HP
Depth: 25mm
Power: +12v = 50ma / -12v = 39ma

Notes: The Timbre is a 6HP Eurorack module based on the wave folder section of the Buchla 259 oscillator as implemented in the Music Easel.

The wave folder adds extra harmonics to input signals that have low harmonic content to create rich and interesting timbres. Typical input sources to use would be Sine and Triangle waves but you are welcome to try other sources as well! The Dannysound Timbre adds an extra input to the Buchla design to allow 2 oscillators to drive the wave-folder simultaneously - this dramatically increases the range of possible tones that can be generated and allows the folder to go wild!

Features:

Osc1 / Osc2 Mix - Adjusts the mix between the Oscillator 1 and 2 inputs, also acts as an attenuator if only one input is used.
Timbre Control - Adjusts the overall amount of wave fold
Timbre CV - Bipolar (attenuator) controls the Timbre CV input
Symmetry - Adds an offset to the input so that the top half of the wave begins to fold earlier
Blend - Mixes between the clean and effected sound

Power consumption: 46mA at +12V and 48mA at -12V

Depth: 25mm

HP : 6

Notes: The Looping VC-ADSR is a 4-stage, loop-able, envelope generator based on the ENVGEN 8C IC from Electric Druid. The individual sections of the Envelope (Attack, Decay, Sustain, Release, Level and Time) can all be individually controlled via CV.

The module has 5 MODES of operation that can be selected via the pushbutton LED switch with the status indicated by the five LEDs above:

Normal Envelope - Gate signal at the GATE/TRIG input, fires the ADSR.
Trigger Mode - Trigger signal at the GATE/TRIG input fires the AD portion of the envelope. The sustain control determines the final value the envelope rests at after the decay portion has ended.
Gated Looping Envelope - ADSR loops whilst gate signal is high.
Looping Envelope - ADSR loops regardless of gate signal.
LIN response (Hold switch to select between LIN/EXP Mode) - Sets the envelope response to be Linear. The response is Exponential when the status LED is off.
When the envelope is looping, all 5 controls affect the output. Attack and Decay operate, as one would expect. The Sustain control sets the minimum voltage the decay part of the envelope will decay to. The Release sets a release time from the end of the Sustain period to the beginning of the next cycle. When the Sustain is set to 0 you can use the Release control to add a delay between the Attack and Decay cycles.

In Normal Envelope mode the Sustain CV input can be used with an LFO source to add amplitude modulation that gradually increases as the Envelope transitions from the Attack/Decay part of the envelope into the Sustain part. The Level CV is also a useful point for amplitude modulation or can be used for Velocity Sensitivity via CV.

The Time CV is set so that increasing voltage shortens the overall envelope time to better mimic the sounds of percussive instruments.

Features:

5 Modes of Operation: Gate Input ADSR, Trigger Input ADS, Gated Loop, Constant Loop and EXP/LIN Envelope Responses
CV over: Attack, Decay, Sustain, Release, Level and Time
Works with Gate or Trigger Signals from +5V to +12V
CV Input Range 0V to +10V
Output CV Range 0V to +10V


Power consumption: 28mA at +12V and 18mA at -12V
Depth: 25mm
HP : 6

Notes: The Dannysound VU Meters is designed to be used with 2 x Dynamics modules. The modules connect internally via 2x3 pin ribbon cables. The meters provide a visual representation of various signals within the Dynamics modules making settings easier.

Features:

External input sockets for monitoring external sources.

Switch to select high or low meter sensitivity or off if the clicking needles get annoying!

Monitoring of the compression/expansion amount.

Monitoring of the unprocessed input level.

Monitoring of the compressor/expander output level.

Power consumption: 0.03mA at +12V and 83mA at -12V at and 3mA at +5V
Depth: 51mm
HP : 8

Notes: 8-input CV expander for Xer Mixa

Expando Expandi adds 8 freely assignable CV inputs to the Xer Mixa in just 4 HP. Connect up to two Expando Expandi to Xer Mixa for easy CV control over channel levels, pan, aux sends, and more.

Expando Expandi is not for use on its own and is currently compatible only with Xer Mixa.

Notes: One of the most ambitious mixers in the Eurorack realm, Noise Engineering's Xer Mixa features a hybrid design with eight stereo inputs plus two stereo aux ins, digital control (including state save/recall), analogue summing and optional CV support via the Expando Expandi module. Immense.

Supplier's Notes:
All-analogue, digitally-controlled mixer with 10 stereo inputs, three stereo outputs, clickless mutes, save and recall, MIDI, and CV via expanders.

Xer Mixa is a mixer with 10 stereo-paired inputs, three stereo-paired output busses, tactile controls, and a 100% analogue signal path with low noise and crosstalk, pristine sound quality, and ultra-high headroom. A digital control interface harnesses the true power of hybrid design, allowing for state save and recall, per-channel pan law and pre/post send settings, multichannel editing, and MIDI I/O.

Xer Mixa features 8 interactive fader-controlled channels and two aux inputs, all with clickless mutes. Configuration options abound for per-channel pan-law settings, pre- or post-fader sends, and channel settings are made simple with the screen. Settings can be saved into preset slots for easy recall for performances or sessions.

Xer Mixa is a compact 32HP, with a streamlined and easy-to-use interface. CV control over almost any parameter is available through the rear-panel connecting Expando Expandi, which adds CV 8 inputs to Xer Mixa. Connect up to two Expando Expandis for easy CV control over channel levels, pan, aux sends, and more. Xer Mixa and Expando Expandi are available together as a discounted bundle, or individually.

Whether you have a massive studio rig or a compact performance system, Xer Mixa is the perfect choice for an expressive mixer.

Notes: All-analogue, digitally-controlled mixer with 10 stereo inputs, three stereo outputs, clickless mutes, save and recall, MIDI, and CV via expanders.

Xer Mixa is a mixer with 10 stereo-paired inputs, three stereo-paired output busses, tactile controls, and a 100% analogue signal path with low noise and crosstalk, pristine sound quality, and ultra-high headroom. A digital control interface harnesses the true power of hybrid design, allowing for state save and recall, per-channel pan law and pre/post send settings, multichannel editing, and MIDI I/O.

Xer Mixa features 8 interactive fader-controlled channels and two aux inputs, all with clickless mutes. Configuration options abound for per-channel pan-law settings, pre- or post-fader sends, and channel settings are made simple with the screen. Settings can be saved into preset slots for easy recall for performances or sessions.

Xer Mixa is a compact 32HP, with a streamlined and easy-to-use interface. CV control over almost any parameter is available through the rear-panel connecting Expando Expandi, which adds CV 8 inputs to Xer Mixa. Connect up to two Expando Expandis for easy CV control over channel levels, pan, aux sends, and more. Xer Mixa and Expando Expandi are available together as a discounted bundle, or individually.

Whether you have a massive studio rig or a compact performance system, Xer Mixa is the perfect choice for an expressive mixer.

Notes: 8-input CV expander for Xer Mixa

Expando Expandi adds 8 freely assignable CV inputs to the Xer Mixa in just 4 HP. Connect up to two Expando Expandi to Xer Mixa for easy CV control over channel levels, pan, aux sends, and more.

Expando Expandi is not for use on its own and is currently compatible only with Xer Mixa.

Notes: 1U TRS

Total flexibility for the Befaco 7U or Intellijel cases rear connectors Jacks.
The channels are reversible and can be used independently for Input or Output.
4 Inputs or Outputs (per module) can be obtained by "AND" cables.
Independent tip and ring attenuators are selectable for each channel to convert the Modular Input Level to Line Output Level.

Features

Selectable attenuator per channel
Fully compatible with Intellijel's 7U and Palette cases.
1U Intellijel format.

Specs

Current needs: Passive
Width: 6 HP
Depth: 20 mm (including power connector)
Designed, kits prepared and completed modules assembled in Barcelona