Search dance music

Notes: LinMix is a compact 6HP mixer suitable for audio signals and modulations CVs.

It is not AC coupled.

Tech specs:

-width 6HP
-42mm depth behind the panel, including the power connector
-standard 10 pin euro power (+12V / -12V) (works also at +15V / -15V)
-power consumption +12V 5mA , -12V 5mA

Notes: Premium quality stereo bus mixer module with balanced and unbalanced output drivers, high end headphone amp and level meters.

Tech specs:

- Panel width 16HP
- 45mm depth behind the panel, including the power connector
- 6 control pots : In 1,2,3,4, Master, Phones Level
- 8 input jacks
- 1 stereo output jack for phones
- 2 unbalanced 6.35mm jack ouputs
- 2 balanced XLR outputs
- standard 10 pin euro power +12V/-12V
- power consumption +12V 150mA , -12V 50mA

Notes: A premium headphone amp module capable to drive low and high impedance phones to high enough SPL, with good dynamic range and very low distortion.

Tech specs:

- Panel width 6HP
- 35mm depth behind the panel, including the power connector
- 1 control pot : Phones Level
- 1 mode switch : Switch from stereo to mono for both channels
- 2 input jacks
- 1 stereo output jack
- standard 10 pin euro power +12V/-12V
- power consumption +12V 100mA , -12V 50mA

Notes: The STATIC module is a comprehensive collection of noise sources generated with different methods.

Tech specs:

-width 10HP
-38mm depth behind the panel, including the power connector
-2 control pots : MORPH, SPECTRUM
-1 switch : spectrum type TR/CHIP
-8 outputs : MSWHITE, MSPINK, ZNWHITE, ZNPINK,
DARK, MORPH, TROUT, RNDVOLT
-standard 10 pin euro power +12V / -12V
-power consumption +12V 35mA , -12V 30mA

Notes: SQUEEZE2 is the improved variant of SQUEEZE:

- SMD transistors are changed to matched through hole ones
- all capacitors are now through hole Panasonic LowESR
- added trimming circuit to adjust 0 gain for the center of make-up gain pot so the SQZ will have 0 amplification on middle adjustments

4HP Compressor designed for continuous adjustment of gain, threshold and compression ratio with a single potentiometer.

There is also a knob for input level and a knob for make-up gain.

The module is based on high-performance THAT4305 Blackmerr VCA chip.

Tech specs:

-width 4HP
-35mm depth behind the panel, including the power connector
-1 audio input : IN
-1 audio level pot : INPUT
-2 control pots : LESS/MORE (compression), MAKE-UP Gain
-1 output : OUT
-standard 10 pin euro power +12V / -12V
-power consumption +12V 25mA -12V 25mA

Notes: VCA2600 needs no introduction. The best sounding VCA in 4HP with matched and thermo coupled transistors.

Tech specs:

-width 4HP
-35mm depth behind the panel, including the power connector
-standard 10 pin euro power +12V / -12V
-power consumption +12V 25mA -12V 25mA

Notes: Describing Univer Inter as merely a MIDI-to-CV module falls short of its immense potential. It serves as an all-encompassing MIDI-to-any-format converter, elegantly packed into a compact 6 HP unit. Connect to your gear via USB B or TRS MIDI, or use the included adapter to plug straight into those 5-pin DIN connecters we all know and love. Whether you're looking to map clock, note, CC, aftertouch or something else that MIDI can encode, UI can do it: we built in over 20 settings for each of the 8 outputs.

Want to control a pair of monophonic voices, complete with velocity and aftertouch? No problem. How about a polyphonic setup, with gate and pitch per voice? Easy. Need to synchronize an in-the-rack sequencer with your DAW or a MIDI clock? UI has you covered.

Eight outputs isn't enough, you say? Chain two UI together via their front-panel MIDI ports and a TRS cable for 16 - you read that right, 16 - configurable CV outputs from a single MIDI connection. The possibilities are endless.

Noise Engineering also made configuration simple via the front-panel USB connection and the easy-to-use Univer Inter section on the Noise Engineering Customer Portal. Go wild and set each channel to any output option you need, or just use one of our simple presets. Configuration files can also be saved as sysex files for easy backup and sharing.

Features

Size and Power
6HP Eurorack
+12v: 40mA
-12v: 10mA

Univer - from Latin: "Universe"

Inter - from Latin: "between"

"Between universes"

What's in the box:
Module
Power cable
5-pin MIDI to TRS cable
USB A to B cable

To reduce excess materials, screws will no longer be included with Noise Engineering modules beginning in 2023.

Notes: Describing Univer Inter as merely a MIDI-to-CV module falls short of its immense potential. It serves as an all-encompassing MIDI-to-any-format converter, elegantly packed into a compact 6 HP unit. Connect to your gear via USB B or TRS MIDI, or use the included adapter to plug straight into those 5-pin DIN connecters we all know and love. Whether you're looking to map clock, note, CC, aftertouch or something else that MIDI can encode, UI can do it: we built in over 20 settings for each of the 8 outputs.

Want to control a pair of monophonic voices, complete with velocity and aftertouch? No problem. How about a polyphonic setup, with gate and pitch per voice? Easy. Need to synchronize an in-the-rack sequencer with your DAW or a MIDI clock? UI has you covered.

Eight outputs isn't enough, you say? Chain two UI together via their front-panel MIDI ports and a TRS cable for 16 - you read that right, 16 - configurable CV outputs from a single MIDI connection. The possibilities are endless.

Noise Engineering also made configuration simple via the front-panel USB connection and the easy-to-use Univer Inter section on the Noise Engineering Customer Portal. Go wild and set each channel to any output option you need, or just use one of our simple presets. Configuration files can also be saved as sysex files for easy backup and sharing.

Features

Size and Power
6HP Eurorack
+12v: 40mA
-12v: 10mA

Univer - from Latin: "Universe"

Inter - from Latin: "between"

"Between universes"

What's in the box:
Module
Power cable
5-pin MIDI to TRS cable
USB A to B cable

To reduce excess materials, screws will no longer be included with Noise Engineering modules beginning in 2023.

Notes: The Z2040 is TipTop Audio's redesign of the most famous analogue filter from the polysynths of the 80's and features Tiptop Audio's signature lush, big, and creamy sound. Its frequency sweeps make thick bass lines and leads with great dynamics. When modulated with audio frequencies through its various inputs, the Z2040 gets quite colourful and is capable of creating many new sounds and textures as the forces of the incoming waves and their harmonics blend through the filter's non-linear circuit. When set with Resonance feedback fully up, the Z2040 transforms into a pure sine-core VC-Oscillator, great for making snappy percussive elements and whistling sounds.

A look under the hood will find that the heart of the Z2040 is a discrete design 4-pole low pass filter with a core similar to that of the SSM2040 filter chip, used in the 80's Prophet 5 Rev 2 synthesizer, and its brother the SSM2044, used in the famous early EMU samplers and PPG synthesizers of the 80's. Both filters are considered by many to be, "the best sounding filter ever".

The Z2040's four modulation inputs are built to handle CV and audio signals, enabling deep modulation of the filter core and passing signals. A VC resonance input is provided to modulate and even clip the sine wave produced by the filter feedback loop. A Frequency Modulation input (FM) provides dynamic filter sweeps and the unique VC-FM index allows modulation of the incoming FM signals. On top of that, the Z2040 comes with an audio VCA that can be configured to act upon the input or the output of the filter.

Size: 8HP
Depth: 42mm
Power: +12V 20ma / -12V 20ma

Notes: Lipsk facilitates the inversion of the individual bits produced by Drezno (or any other module connected to its input header at the back), and delivers the resulting code to its output header. Bit inversion can be manually controlled by pressing any of combination of its eight illuminated buttons, or it can be automated by patching gate signals into its gate input sockets. An active (5V) gate flips the state of the respective bit. If the button is active (bit already flipped), then the gate flips the bit again yielding double inversion (no inversion). The corresponding LEDs show the combined effect of both manual and gate actions. The bit processing logic is hardware-based, so there is virtually no latency, allowing the binary signals to be manipulated at extreme rates.

Notes: The 2hp Buff is a buffered multiple capable of splitting an input signal to multiple outputs. Due to its active architecture, inputs retain their full integrity as they are copied to multiple destinations. One input signal can be copied to six outputs, or two inputs can be copied to three outputs each. The Buff is especially great for splitting pitch or audio signals where signal integrity is critical. Keep your signals in shape with Buff.

Notes: MISO is a multipurpose utility module, a laboratory for synthesizing control voltage signals and audio. MISO combines multiple CV tools into one module for making complex CV shapes at the output stage. The name comes from the four main functions available: Mix, Invert, Scale, and Offset.

MISO's 2 sections (1/2 IN and A/B IN) are identical. Each section has two inputs that can be used to Mix signals, Invert polarity/shape, Scale magnitude and Offset voltage. Each function can be used independently or simultaneously with the total shape summed to the mix output.

At the centre of the module is another processor, an accurate smooth linear voltage-controlled crossfader that mixes equally between the outputs of the top and the bottom MISO sections. Feed the MISOs with envelopes, LFOs, Sequences to create new shapes and then crossfade them manually or with CV using the centre section for even further complexity of shapes and animation of control signals. Crossfade between the waveforms of a VCO or audio samples with CV for more motion.

There are an endless number of ways to patch MISO with unexpected and inspiring results. MISO is the kind of module that gives modular synthesizers its incredible replay value, rewarding hours of creative explorations and its experimental and non-traditional mixing.

MISO offers a lot in a small comfortable module that matches Tiptop's system look with clean white faceplate styling. A red/yellow indicator light next to each section makes it easy to see signals and visualize polarity.

Notes: Sine is a harmonically pure VCO with two distinct outputs.

The primary output contains a perfect sine wave with a wide frequency range and pristine volt per octave tracking. The Sub output features two sine tones that can be blended together to achieve a mix of one octave below, or a fifth above the primary output's frequency.

In addition, both outputs have an internal wavefolder that adds harmonic content to the signal allowing for spectrally complex tones within a single module. Keep your tones pure (or not!) with Sine.

Notes: Terci Ruina combines three classic distortions in 4 hp. Distortions are reinterpreted in classic NE style and routed through each other for complete sonic annihilation of any sound. Patch in and out anywhere in the signal chain to pick the best sound for your purpose (because modular). Looking for a pretty distortion? This is probably not your module. Unapologetically gross and dirty.

Notes: The Mankato Filter is a four-pole lowpass filter with positive and negative outputs at every pole, giving you slopes of 6 dB/oct, 12 dB/oct, 18 dB/oct, and 24 dB/oct simultaneously. The negative slope outputs allow you to use the Mankato as a quadrature sine oscillator with 8 available phases. The Mankato will self-resonate from subaudio to superaudio, and responds to one volt per octave through its unattenuated control inputs. When resonating, the 6dB/oct outputs are slightly hotter than the others and can be driven to lightly saturate at full resonance. The signal inputs are DC coupled, which allows you to use the Mankato as a voltage-controlled slew limiter at very low cutoff frequencies.

Notes: The BF-22 VCF is a dual Hi/Low-pass filter inspired by the Sallen-Key filter from the early MS-20.

DISCLAIMER: This filter brings to your modular system the character of early MS-20 sound: Kick-ass-rocking-dirty screams! It inherited not only it's amazing sound, also MS-20 noise floor. If noise floor is an issue for you, this might not be your filter.

Features:

Dual-channel Sallen-Key Filter. Inspired by the early MS-20
High and Lowpass operation.
Two CV inputs per channel with a dedicated atenuverter for the first one.
CV controlled resonance.
The first channel can be linked to the second one with the "Link" switch.

Specifications:

Current needs: +12V: 40mA, -12V: 20mA
Width: 17 HP
Depth: 30mm (including power connector)
Aluminiun, heat-treated front panel
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: The EVEN VCO is a voltage-controlled oscillator that offers stability and high precision tuning over 10 octaves. A redesigned temperature compensation circuit maintains the oscillator stable against voltage and temperature drops.

Specifications:

Current needs: +12V: 36mA, -12V: 26mA
Width: 8 HP
Depth: 22mm, (28mm DIY) including power connector
Aluminium, heat-treated front panel.
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: The Sampling Modulator is a multi-function module that lies somewhere between a VCO, a Sample & Hold, and an 8 step trigger sequencer.

Sequencer Clocked Sample & Hold

In this mode it acts like a regular Sample and Hold (S&H) but since it is "sequencer clocked", it is capable of much more interesting patterns than the usual S&H melodies.

The CLOCK input can work in two ways: 1. As a typical clock 2. In "positive going hard sync" mode allowing you to create shuffling and polyrythmic effects.

The HOLD input can be used to keep certain notes playing.

Analog Down-Sampling Effect

In this mode (with the clock running at audio rates) you can go from nasty and harsh sampling rate reduction to an almost clean signal. (The clock run up to 25Khz without external CV and up to 200Khz with CV on the input).

Sampling Modulator/Shaper

Thanks to the V/Oct clock, by feeding a simple waveshape such as a sine wave to IN, and pitch CV to the VCO as well as to the Sampling Modulator CV input, their related frequencies and aliasing caused by the sampling rate reduction are capable of creating clangorous metallic sounds, 8 bit textures and much more.

The game becomes much more interesting when you try to destroy the wave by flipping on and off the switches of the sequencer (which at times can make it sound like three VCOs running in unison).

To understand how the Sampling Modulator works, keep in mind that we are working with a temperature compensated ramp core VCO with more than 4 octaves of tracking. This allows the timbre to stay the same while you move through the scale as the internal and external VCOs are synced in a fashion similar to "frequency related sampling rate modulation"

Unusual V/oct VCO You can use the trigger outputs as a pulse VCO. Flipping the switches on and off the switches can offer a lot of interesting timbral changes.

Notes: A four channel mixer, suitable for audio or control signals. It features regular and inverted outputs as well as an LED level meter.

Specifications:
Current needs: +12V: 21mA, -12V: 10mA
Width: 5 HP
Depth: 20mm (including power connector)
Aluminiun, heat-treated front panel.
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: Crush Delay v3 is a special Echo-Delay unit based on the PT2399 IC, which is able to offer 400ms of clean delay and up to 2 seconds of dirty repetitions, having a special talent to generate noisy-glitch textures. The module bases its operation on controlling the PT2399 chip with circuit bending techniques, converting the unit in an advanced VC digital trash generator. This third version comes with some interesting new features like redesigned VCAs circuits, wider range for clean delay and reduced depth to make it skiff friendly.

The module features a few VCAs to provide a flexible signal route to maximize module's possibilities. First two VCAs at the inputs to control the amount of signal sent to the delay. The first is routed to both the dry/wet mix and the delay, and the second directly to the delay. Combining the second VCA and the FX Send output allows external feedback routings.

Compared with v2, this third version offers a bigger range of clean delay time as well as a revision of some of the Crush modifiers. Combining those modifiers you will have a access to a vast palette of noises and textures that can be used in many different ways. From ambient/drone patches to even percussion sounds.

The VC Feedback features an automatic gain control to keep levels stable at any feedback level.

- Current needs: +12V: 135mA, -12V: 35mA
- Width: 11 HP
- Depth: 30 mm (inc power connector)
- Aluminium, heat-treated front panel
- Designed, kits prepared and modules assembled in Barcelona

Notes: A compact attenuverting (attenuator-inverter) joystick controller and Gate Generator. With it, you can generate and process two control voltages using only one hand. Provided controls for CV ranges and offset adjust the boundaries of your control, this way it never gets out of the desired range, ensuring sensibility and playability even with wild performance gestures.

Specifications

Current needs: +12V: 25mA, -12V: 10mA
Width: 12 HP
Depth: 35mm (including power connector)
Aluminium, heat-treated front panel.
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: The second batch of Animal Factory's dual-valve saturation all-rounder features hand-matched 6J32P valves for a faster, slightly more precise take on this unique blend of mixing, VCAs, distortion and wave folding.

Supplier's Notes:
Orobas is a dual tube amplifier that is composed of two identical units.

Each channel has two audio inputs with dedicated gain controls and one output volume control.
Thanks to clever routing, a wide variety of sounds can be created. The two channels can be connected in parallel or in series (Parallel / Series). In series connection, the output of channel 1 is still active, good for parallel signals (note: each channel output is phase-inverted in relation to the opposite input). This way, feedback can be generated by feeding back the signal from output 1 to e.g. a control voltage input.

The screen control voltage input determines the gain and the sound characteristics. Additionally, the input is normalized to INPUT 1 of the respective channel.

The Suppress control voltage input is normalized to the input signal if nothing is connected. The purpose of this input is to direct electrons reflected from the anode back to the anode. Turning the knob to the positive does not change as much, turning it to the negative slightly attenuates overtones. With a positive control voltage the change is minimal, but with a negative control voltage you can realize e.g. ducking effects and effectively switch off the tube. Audio Rate Modulation is also possible here and a bit milder than with the Screen CV, but still effective.

The evocation potentiometer controls the feedback of the second output into the first channel. The sonic performance is very much dependent on the Plate Bias switch. The Plate Bias switch effectively controls the headroom. This allows you to use the tubes in three different settings, from fuzz sound to full distortion.

*This version is equipped with other tubes than in version 1.

Tube length: 55mm

Depth: 45mm

Notes: Module A-130-8 contains eight linear voltage controlled amplifiers (VCAs). Each VCA features a control voltage input (CV), a signal input (In) and a signal output (Out). In addition three mixers are included: the socket labelled "1-4" outputs the sum of the VCAs 1-4, the socket labelled "5-8" outputs the sum of the VCAs 5-8, the socket labelled "1-8" outputs the sum of all eight VCAs.

The signal inputs are able to process levels up to 10Vpp without clipping. Each CV input is equipped with a trimming potentiometer that is used to adjust the sensitivity of the CV input in question. In the factory the module is adjusted for the CV range 1...+5V but can be re-adjusted by the user for other control voltage ranges (e.g. 0...+10V).

The amplification range for each single VCA is 0...1. The signals of the sum outputs have a lower amplification to avoid distortion.

The VCAs and mixers are fully DC coupled, i.e. the module can be used for the processing of both audio and control voltage signals. The control voltage and signal inputs can be normalled by means of small solder pads (e.g. 1 > 2 > 3 > 4 and so on, or 1 > 5, 2 > 6, 3 > 7, 4 > 8 for the stereo application mentioned below).

Typical applications:

Any kind of VCA application (e.g. voltage controlled attenuation of audio or control voltage signals)
Two voltage controlled mixers with four channels each
Voltage controlled stereo mixer with four channels each, for this the control voltage inputs have to be correspondingly patched or internally normalled: CV1=CV5 / CV2=CV6 / CV3=CV7 / CV4=CV8
Voltage controlled mixer with eight channels
Add-on for the planned Joystick module A-174-4

Dimensions
6 HP
40 mm deep

Current Draw
50 mA +12V
50 mA -12V
0 mA 5V

Notes: The Doepfer A-126-2exp is an expander for the A-126-2 Voltage Controlled Frequency Shifter.

It adds two outputs from the Dome filter (+45 and -45 degrees) as well as separate outputs from the ring modulators 1 and 2, and from the internal envelope generator. Furthermore, it offers dedicated outputs for Up and Down Shift, allowing the module to be patched in stereo.

*Note: The expander can only be used in conjunction with the module A-126-2.

HP : 2

Notes: The Doepfer A-126-2exp is an expander for the A-126-2 Voltage Controlled Frequency Shifter.

It adds two outputs from the Dome filter (+45 and -45 degrees) as well as separate outputs from the ring modulators 1 and 2, and from the internal envelope generator. Furthermore, it offers dedicated outputs for Up and Down Shift, allowing the module to be patched in stereo.

*Note: The expander can only be used in conjunction with the module A-126-2.

HP : 2

Notes: Erica Synths Black Quad VCA2 is a versatile four channel voltage controlled amplifier and mixer module for use in complex modular systems. Each channel has linear/logarithmic response selector and signal level indicator LED. All outputs are sequentially mixed and CV inputs are normalled to each other, so you can use the module in various configurations. If no CV is applied, the Black Quad VCA2 performs as a signal mixer, and the 4th channel is DC coupled for controlling CV sources, as well.

Notes: 32 unique audio effects arranged in 4 banks of 8 effects. Three effect controls plus analog Dry/Wet control with dedicated CV input. High quality stereo signal pass. Separate modulation inputs for all three effect parameters plus Sample Rate Reducer (SRR) input - changes internal clock. Four user storable presets - stores selected program and all three controls. Spin FV-1 based.

The last used effect, and presets are always remembered.

32 effects are simultaneously available, but FX AID can be reflashed with other effects in any order.

Reflashing procedure is quite easy: playing 40 sec long "wav" file of line level amplitude to SRR input.

Reflashing mode: hold both buttons for 10 sec.

By default it runs on 32.77 kHz and, this sample rate can be decreased down to 150 Hz or brought up to 48 kHz via SRR input.

Please note the reverse CV operation of the Dry/Wet control: positive CV crossfades from Wet to Dry, and negative CV crossfades from Dry to Wet.

80 mA +12V
30 mA -12V
45 mm deep

Notes: An analogue oscillator with through-zero phase modulation. The core of the T-ZED is the SSI2130 integrated circuit. Voltage controlled wave shape and phase modulation index allow for automated sonic versatility, and 2 separate frequency ranges mean the T-ZED can be used as an audio or CV source.

Features

Simultaneous SINE, TRIANGLE, SAW, SQUARE, and variable SHAPE outputs
Phase MOD input with bipolar INDEX circuit
V/OCT input tracks 10 octaves
FREQ spans 10 octaves, TUNE spans 1 octave
Hard SYNC input
SHAPE output (Sine to Triangle to Saw) with CV input and attenuator
Frequency range HI: 10hz-25khz
Frequency range LO: 0,1hz-200hz


Dimensions
12 HP
25 mm deep

Current Draw
55 mA +12V
45 mA -12V

Notes: Designed for Frap's CGM Creative Mixer modules, the Masterone takes an input via IDC socket rather than standard Eurorack connections, then feeds out to headphone outs, balanced stereo XLR, TRS and mono.

Supplier's Notes:
The Masterone is the first Frap Tools module designed to be connected exclusively with non-Eurorack equipment.

It features four separate output sections with different Neutrik connectors and adjustable gain levels to suit the most common live and studio situations (and even some uncommon ones).

With no inputs and just large-format outputs, it pushes even further the concept behind the M module: being a Eurorack system's gateway to the outside world.

XLR Balanced Stereo Outputs

Two XLR connectors (left and right) provide a balanced output with the expected 6 dB extra gain. In many cases, they can allow bypassing a DI box.

TRS Pseudo-Balanced Stereo Outputs

These outputs are very similar in concepts to the ones on the M module, but with large 1/4" jack connectors. It is possible to patch standard TS cables and use them as unbalanced outputs, or use TRS cables to interface them with balanced equipment (the ground is routed to both the ring and the sleeve, for a better performance than regular unbalanced outputs).

Attenuation Switches for Flexible Connectivity

If the two stereo outputs are too hot, a set of switches can attenuate them. The Line/Mic switch on the XLR outputs attenuates them by ~30 dB, while the Line/Inst switch on the TRS outputs attenuates them by ~15 dB.

Stereo Headphones Output with Pre-Fader Listening

The Headphones section allows you to monitor the Master output with an independent volume knob and, at the same time, take advantage of the PFL function on the Channels and the Groups. Rotate the PFL crossfader towards the blue section to blend the PFL modules with the Master sum and check if everything is okay before launching the next scene.

Mono Output with Dedicated Fader

Should you need an extra monitor on stage, or run the whole system through a vintage amp in the studio for parallel processing, the auxiliary monophonic outputs is the answer. It provides the sum of both channels in a handy, pseudo-balanced output with a dedicated fader: attenuate the line level by 15 dB, or amplify it by 6 dB.

12-LED VU Meter with Memory

A detailed VU Meter monitors the signal amplitude from -40 to +15 dB with peak memory on the upper LEDs.

Dimensions:

12HP

38 mm deep

85 mA +12V - 80 mA -12V

with headphones at high level (250O)

110 mA +12V 105 mA -12V

Notes: Erica Synths Fusion Dual Mixer is designed to mix and overdrive audio signals on the vacuum tube.

Use the Fusion Mixer as two independent 3-input mixers (also for stereo signal mixing) or a 6-input mixer. Special feature of the Fusion Mixer - great tube overdrive effects when level knobs are set to 3 o'clock or above. When used with drum machines, it even emulates sidechain compressors. When used to mix signals from VCOs Fusion Mixer it works as waveshaper, especially, if pulse width modulated pulse signals is used in one of inputs.

All Fusion modules by default are configured to work with regular eurorack PSU.

Due to the fact that cold tube heaters have lower resistance, Fusion modules have significant power consumption peak at startup, when power consumption almost doubles for 1-2 seconds. This is not a problem with linear PSUs that have power inertia, but may cause switching PSU internal protection to turn off power supply. Please make sure your PSU has some headroom before installing multiple Fusion modules.

Technical specifications:

Input signal level: up to 20V ptp
Output signal level: 10V ptp
Mixer GAIN: 1
Power supply: bipolar +-12V , eurorack standard
Power consumption: Eurorack PSU configuration: 160mA@+12V, 10mA@-12V
Module width: 14HP
Module depth: 25mm

Notes: Erica Synths Black VCO Expander essentially is an advanced waveform mixer plus two octaves down suboscillator, it allows you to explore wave design in brand new areas.

Features
Waveform mixer/inverter
Sine/Triangle/Tits waveform switch
Transistor-based -2 octave suboscillator
-1 and -2 octave suboscillator crossfade
Suboscillator lowpass filter
Diode limiter on output signal amplitude
Three simultaneous outputs

Erica Black series are high-end modules with unique functionality. Only the highest quality components are used and all inputs and outputs are protected against undesired overvoltage. When designing the Black Series, we did not economise on the module width, we put design and usability first. Big knobs are assigned to functions that make difference in sound. Together the Erica Black series are a range of modules that make an entire synthesizer.

NB! This expander module can be connected only to Black VCO and Black VCO2. It will not work as a standalone eurorack module.

Dimensions
10 HP
25 mm deep

Current Draw
5 mA +12V
5 mA -12V

Notes: Erica Synths Black Mixer is compact, high quality audio mixer with bonus features - mute switch on each input and three buffered outputs. This allows you to add audio signals to your mix instantly and in exactly right level, plus you can send signals to several post-mixer devices simultaneously, for example, split the output signal to LP and HP VCFs and create advanced bandpass and notch filters.

Technical specifications:
Max input level: -10V - +10V
Mixer gain: 1
Power consumption : +8mA, -8mA
Module width: 6HP
Module depth: 25mm

Notes: Introducing a four independently buffered input mixer and a buffered output signal splitter, in one module!

Erica Synths Black Mixer/Splitter V2 is an advanced replacement for stackable patchcables.

Everyone who knows a bit more about electronics will point out that stackable patchcables are not a really wise choice for such sensitive things as musical instruments because they mechanically connect electrical signals that at best can cause undesired modulations or even damage the modules.

Erica Black series are high-end modules with unique functionality. Only the highest quality components are used and all inputs and outputs are protected against undesired overvoltage. When designing the Black Series, design and usability were prioritised first. Big knobs are assigned to functions that make difference in sound. Together the Erica Black series are a range of modules that make an entire synthesizer.

Technical specifications:

Input signal level: -10V - +10V
Power consumption: +25mA, -25mA
Module width: 4HP
Module depth: 25mm

Notes: Module A-115 is a four-way frequency divider. The frequency of a signal at the input is halved (half frequency = first sub-octave), quartered (1/4 frequency = second sub-octave), and so on. In this way, the DIVIDER produces four sub-octaves (F/2 down to F/16).

At the output, the A-115 produces a summed mix of the original and the four sub-octaves. There are attenuators to control the amount (i.e. Amplitude) of the original signal and each of the sub-octaves.

Bear in mind that the sub-octaves output by the A-115 are all true square waves. At the output there are always four square waves and the original signal available.

Notes: Incredibly powerful two-channel filter module capable of much more than just filtering. State-variable digital filters with built-in VCAs designed to overdrive beautifully. Sounds great.

Supplier's notes:
BIONIC LESTER MARK III is a 2-channel 2-pole state-variable digital filter with an unusual amount of good sonic character. The filter mode is continuously variable under manual or CV control, smoothly fading from lowpass to bandpass to highpass to notch to allpass with a single motion. The resonance stops just short of self-oscillation. A digital VCA controls the amplitude and the distortion of the input signal pre-filter. The filters have independent inputs and outputs, and an additional Mix output with balance control. The filter design was initially inspired by the best of late-1990s "virtual analog" filters and has gone far beyond.

The audio input controls have dual behavior. When the control (or CV input) is turned from zero position to the center, it operates as a simple gain control for that input. When turned past the center position towards the maximum, the signal will begin to soft-clip, adding hard clipping as the maximum is approached. This smooth and subtle distortion adds violence to otherwise unremarkable input material, generating additional harmonic content for the filter to process. The digital VCA that controls the gain and distortion functions is aware of the input signal's zero crossing, eliminating "clicking" noises when the gain is modulated.

Each filter section has three CV inputs. The first is a high-speed input hardwired to the filter's cutoff frequency, appropriate for snappy envelopes and slow moving voltages alike. The other two inputs (one with attenuverter control) are freely assignable to any of the filter parameters (cutoff, resonance, mode, gain), storable in a preset. The Mark III preset system stores eight fully programmed panel setups, instantly recalling everything under the harshest demands of performance. The Morph mode allows smooth fading between all of these presets.

Activate Filter B's LINK control for patch-free routing of the filter's control or audio signal. You can achieve dual-peak resonance, cable-free series routing, cascaded 4-pole filtering (with two stages of distortion), and full stereo using only one set of filter controls. The input normalization, LINK settings, and parallel mix output further reduce cable clutter while rapidly patching an elaborate signal flow.

The controls are arranged for maximum tweakability and minimum cable interference, with metal-shaft potentiometers attached to the panel on the large knobs. The Mark III OLED display displays the cutoff frequency in Hertz, resonance amount, and filter type morph. The CV inputs process all input voltages between -10 to +10 volts. Panel size is 15HP.

Notes: The Spherical Wavetable Navigator (SWN) is a six-channel synthesiser that makes it easy to create slowly morphing drones, polyphonic melodies, evolving sequences, and rich textures.

The SWN features six wavetable oscillators with independent pitch, level, and waveform controls. Six LFOs (Low Frequency Oscillators) can be used as modulation sources and/or envelopes, making it easy to add dynamic motion to your patch. Each channel is a full voice and can be "played" using the top row of buttons, the internal LFOs, or note-change detection on the 1V/oct jacks. The SWN ships with 12 three-dimensional (spherical) wavetables and an easy interface which allows you to record and edit custom wavetables from live audio. Open-source software for Mac, Windows, and Linux called SphereEdit can be freely downloaded and allows you computer to create, edit, and convert .wav files into Spherical wavetables to transfer into the SWN with an audio cable.

New firmware available which adds extra features, visit https://4mscompany.com/p.php?p=820&c=5 for details.

Notes: Polyphony is back!

Chord v2 is a plug and play solution for bringing musical polyphony to your system. It contains four oscillator voices, a multitude of waveforms, and intelligent tuning functionality. This new version features an expanded sonic palette and feature set in half the size of the original.

It features three primary modes of operation: Chord, Free Running, and Unison. These three modes allow the oscillators to be tuned as diatonic chords, run independently of each other, or be tuned to the same internal frequency for external v/oct sequencing through independent CV inputs.

The timbral possibilities of the Chord v2 bring its polyphonic tones to life. The module ships with eight banks of waveforms encompassing traditional shapes, vocal synthesis, organ emulation, and chiptune sounds. You can also load custom wavetables using the SD card slot on the front panel.

From harmonic drones to Switched On Bach, the Chord v2 is an unparalleled addition to any Eurorack modular.

Changes from v1:

- Half the size! 14HP down from 28HP
- Eight banks of waveforms
- Full polyphonic mode
- Harmonize in minor mode
- Custom wavetable compatibility
- Expanded chord types
- Improved synthesis engine

Notes: This product is used to produce drum and percussion sounds. You can make 909 type of kick drums- the toggle switch on the left chooses between long and short vca decay. The toggle switch on the left chooses long and short pitch envelope decay. Smack knob control lefts you mix in a noise 'paper' sound for the drum.

You can mix in two trigger sources to create complex percussion patterns. The internal circuit is using logic 'OR' triggering.

This product was refined for optimum sound and response from the controls. Part values were changed from the original 909 design.

-There is onboard distortion to get techno type of kick drums.

-This internal oscillator is triangular core, with internal reset.

-The internal trigger conditioner can take audio rate frequencies.

-There is a manual push button.

Width: 10hp

Current: +30mA,-24mA

Notes: VCA 3X is a simple yet great solution for synth users looking to add more VCAs to their setup in a single and compact module. This module features 3 VCAs with individual Signal and CV inputs and outputs.

Notes: Erica Synths Modulator is an advanced modulation and pitched noise source with focus on rhythmic (but not limited to) compositions in mind. It features two identical syncable to the BPM LFOs/noise sources with selectable morphing waveshapes. LFO frequency can be manually adjustable, as well as they provide frequency divisions and multiplication in Sync mode. Each LFO has two outputs- main one and secondary one with adjustable phase, so you can create evolving modulations. Furthermore, LFOs can be linked to work at the same frequency and the first LFO has built in VCA to control output signal amplitude.

Features
Two independent modulation/pitched noise sources
7morphing waveshape + noise
LFO Sync, frequency divisions and multiplications
Integrated VCA for first modulation source
Two main outputs
Two outputs with an adjustable phase shift
LP and HP filter on outputs in pitched noise mode
CV control over LF rate/noise pitch

Output level: -5...+5V
CV level (full span): -5V - +5V
Power consumption: 86mA@ + 12V, 7mA@ - 12V
Module width: 10HP
Module depth: 45mm

Notes: Erica Synths Cymbals is a distinct topology digital/analogue module, where cymbal samples are passed thru AS3330 based VCA and controlled via envelope generators of unique design. The module features 10 sets of custom Crash and Ride cymbal samples with Tune control and individual Decay control. Accent and CV control over Tone and Decay allow you to create lot of variations in the Cymbals track. An extra feature is sample looping - when it's on, a certain part of the sample is looped while the envelope decay is on, thus creating a distinct, delay-like effect. Cymbal samples are developed by producer and musician Nero Bellum.

Features
10 sets of custom cymbal samples
Analogue VCA and EG
Tune and Decay controls
CV control with an attenuators over Tune and Decay
Sample loop for Crash and Ride
Manual triggers
Accent for better expression

Audio output level: -5...+5V
CV level (full span): -5V - +5V
Accent CV level: 10V
Tigger level: 5V
Trigger time: 1ms
Power consumption: 95mA @ +12V, 36mA @ -12V
Module width: 10HP
Module depth: 45mm

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Module A-121s is a dual multimode filter which can be used for stereo applications as well as for parallel or serial organized dual mono filters. The core is a 12dB multimode filter identical to the modules A-121-2 and A-121-3. The selection of the filter type is continuously from lowpass via notch and highpass to bandpass. We attached great importance to the usability of the manual controls and CV inputs for both stereo and dual mono applications. For the filter parameters frequency (F), resonance (Q) and type (T) common controls and CV inputs as well as single controls and CV inputs are available. For the filter frequency in addition a manual control and CV input for the filter spread (frequency difference or delta F) is available.

Controls:
F: master frequency control for both filters (large knob)
Type 1 / Type 2: filter type panning/morphing L-N-H-B
Link to 1: Toggle switch so that Type 1 also controls type of filter 2 (i.e. simultaneous filter type control for both filters)
SFM1 / SFM2: Single Frequency Modulation controls (polarizers), connected to the corresponding sockets SFM1/SFM2 (socket SFM1 is normalled to a fixed positive voltage, SFM2 is normalled to SFM1, that way the controls SFM1/SFM2 work as frequency controls for each filter provided that no modulation signals are patched to the SFM1/SFM2 sockets)
CFM: common frequency control, controls two VC-polarizers which process the signals connected to the two sockets CFM1/CFM2, CFM2 is normalled to CFM1, that way also the same modulation signal (e.g. an envelope generator) can be used for both filters and the level controlled simultaneously by the CFM control
Delta F: controls the difference between the frequencies of the two filters manually (frequency "spread"), at centre position the frequencies are the same
Delta FM: controls the level of the Delta FM signal (socket), which allows to control the spread between the frequencies also by an external control voltage (e.g. by an LFO or ADSR)
Q: controls the resonance of both filters simultaneously
Level 1 / Level 2: attenuators for the two audio inputs
QM/TM1, QM/TM2: attenuators for the modulation inputs QM/TM1 and QM/TM2

Sockets:
In1 / In2: audio inputs (In2 is normalled to In1)
Out1 / Out2: audio outputs
F: common frequency control input for both filters (~ 1V/oct)
Delta FM: Control voltage for frequency spread, processed by the polarizer Delta FM
SFM1 / SFM2: single frequency modulation inputs, processed by the polarizers SFM1 and SFM2, SFM1 is normalled to a fixed positive voltage, SFM2 is normalled to SFM1#
CFM1 / CFM2: common frequency modulation inputs, processed by the two voltage controlled polarizers controlled by CFM knob, CFM2 is normalled to CFM1
QM/TM1, QM/TM2: the addressing of these sockets/attenuators is defined by internal jumpers. QM means Q modulation (i.e. resonance modulation), TM means filter type modulation (QM1 = resonance modulation filter 1, QM2 = resonance modulation filter 2, TM1 = filter type modulation filter 1, TM2 = filter type modulation filter 2), socket QM/TM1 is normalled to a fixed positive voltage, QM/TM2 is normalled to QM/TM1
A 45 degrees triangle next to a socket means that the switching contact of the socket is normalled to a fixed positive voltage (SFM1, QM/TM1).
A vertical triangle indicates the normalling of two sockets (In1>In2, SFM1>SFM2, CFM1>CFM2, QM/TM1>QM/TM2).

If the filters do not behave as expected please pay attention to these peculiarities:

For the controls SFM1, SFM2, CFM, Delta F and Delta FM the centre position is the neutral position as these are polarizers. If the filter behaves unexpected these controls should be set to centre positions for the time being.

For the controls F, Q, Level 1, Level 2, QM/TM1 und QM/TM2 the fully CCW position is the neutral position as these are standard attenuators. If the filter behaves unexpected at least the controls QM/TM1 and QM/TM2 should be set to fully CCW. Via the normalling of the sockets QM/TM1 and QM/TM2 and the associated controls the filter parameters adjusted by the major controls (e.g. Type 1, Type 2 or Q) may be overwritten.

By means of small circles at the bottom right side of the front panel the user can mark the function of the QM/TM inputs. These assignments are possible:
QM/TM1 controls QM1, QM/TM2 controls QM2, the filter types are not controlled by external CVs
QM/TM1 controls TM1, QM/TM2 controls TM2, the resonances are not controlled by external CVs
QM/TM1 controls QM1 and QM2 simultaneously, QM/TM2 controls TM1 and TM2 simultaneously

Notes: Quantus Trajecta is a quad envelope designed with polyphony in mind. Quantus Trajecta's envelope structure takes the functionality from Noise Engineering's beloved Loquelic and Cursus Iteritas Percido modules, and adds even more control and mode options like Tremolo and ADSR.

Each parameter is CV controllable, and each control universally adjusts all four envelopes for easy polyphonic tracking. Quantus Trajecta is performable, musical, and most importantly, fun.

Notes: Jam Jam is a versatile and fun trigger-and-gate processor with four individually adjustable and CV-able channels. The three modes pack incredible functionality into the tiny 6hp package.

Random mode turns the module into four individually adjustable probability processors, great for adding variety to a patch.

In Clock Phase mode, the module adjusts incoming clock phase based on clock period. Use this to adjust sequencer timing or to create sequences that drift out of sync and then back in with CV.

Use Gate Delay mode as a simple trigger delay to help keep things in sync in your patch or for creative patching: dial in shifts in the timing of events from sub-millisecond adjustments to huge delays of over 15 seconds.

Jam Jam is a musical and fun utility sure to find a use in every patch.

Notes: A clever approach to VCOs here. Three unevenly phased sawtooth signals are blended to create phase cancellations and unorthodox harmonics. Simple but deep.

Supplier's Notes:
Explore the sonic space of phase cancellation! Phase cancellation shapes the characteristics of all acoustic instruments. It forms the basis of chorus and phaser effects. It gives vibrancy to detuned oscillators. The vibrant sound of pulse width modulation or the roaring sound of animated supersaws are a small part of a much larger sonic space that the Triphase Oscillator is built to discover.

The Triphase Oscillator produces three different sawtooth waves at the exact same pitch but with independent phase control. These are blended in a bipolar CP3-type mixer, giving a rich waveform at the output. By blending in a wave with a positive polarity, you reinforce in-phase harmonics; by blending a wave with a negative polarity, you reduce in-phase harmonics. The phase differences between the waves distribute the harmonics from in-phase to out-of-phase. The result is a comb-filter effect, like the effect produced by an acoustic reflection, with notches and peaks spaced evenly throughout the frequency range. Conventional pulse width modulation can be obtained by blending two sawtooth waves with equal but opposite polarity. Supersaw-like behavior can be obtained by using phase CV with the same polarity for all three waves. But many other interesting spaces can be reached. For example, by setting the phases correctly you can cancel out the first harmonic and get a saw an octave higher, or cancel both the first and the second harmonic, giving you a saw an octave and a fifth above the fundamental frequency. Modulation then brings back these canceled harmonics.

The Triphase Oscillator is completely analog, built around a sawtooth core that is functionally stable and accurate but sonically alive. It has linear FM on all three waves, and an excellent hard sync that can create shredding harmonic sweeps. The CP3 type mixer gives good distortion at higher levels, allowing you to blend three 5-volt-peak waves without worrying about headroom. All CV functions at audio rate. With an LFO driving the phases, it can easily replace the classic analog three oscillator setup, and in this configuration it's one of the fattest things you have ever heard. But the Triphase oscillator is much more than a thickener, and can just as easily produce thin reedy sounds or subtly shifting harmonic drones.

Specs

Size - 18HP
Depth - 25mm
Power Consumption
+12V 50mA
-12V 50mA

Tuning Range
1.2Hz-61kHz

Tuning Accuracy
~8 octaves

Output Range (Individual)
-5V-+5V peak

Output Range (Mix)
-8V-+8V peak

Notes: Yep, it's an attenuator. With a fancy name! And LEDs!

Sinc Defero's inputs are circularly normalled, too, so you can use it as a mult by leaving inputs unpatched.

Features:

Size and power:

4HP Eurorack
+12v: 45mA
-12v: 40mA
Sinc - from Old English sinc for "treasure" and Greek clastic for "easily removable"

Defero - from Latin for "sloping down"

"Portable treasure reduction"

What's in the box:

Module
Power cable
To reduce excess materials, screws will no longer be included with Noise Engineering's modules beginning in 2023.

Notes: Subway is a scanning crossfader with 8 inputs and 1 output.

The eight inputs can be used for control voltages as well as audio signals. A potentiometer or CV can be used to mix between the individual sources. Each of the inputs also has a manual on/off switch.

Application examples

Complex modulations
Waveform selector for oscillators or noise
Morphing waveforms from wavetables
Switching between different envelopes
Controls:

Scan knob - master control over which input goes to the output. The knob is shifted when a CV is applied to the scan CV input.
Enable switch - Controls which input is active. When the LED is off, the input is removed from the output selection. A dim LED means the input is active but not yet selected. Bright LED means that the input is currently being sent to the output.
Curves: Subway has three different curves if you hold down keys 1-3 when switching on and then release them. Button 1 sets a linear curve, button 2 sets an exponential curve and button 3 sets a steady curve.
Power consumption: 80mA at +12V and 22mA at -12V

Depth: 38mm

HP : 6

Notes: The Touellskouarn Eread Jedonian is a quad splitter from TRS to 2x mono mini jack combined with a bidirectional Hz/V converter. Additionally it offers V-Trig to S-Trig conversion.

The Hz/V standard works with Korg MS and old Yamaha CS among others.

Notes: Blokan is a ring modulator for Eurorack based on tubes and transformers. It is built like a classic diode ring modulator, but the diodes are tube based.

The built-in VCO provides the carrier signal (saw wave) and can also be tapped using a dedicated output. The VCO provides a voltage control input. The carrier signal can also be replaced by an external signal.

The module sounds different from conventional ring modulators due to the tubes. There may be slight noise and the carrier wave may crosstalk in the output.

Technical

Size: 12hp
Face plate material: 2mm anodised Aluminium
+12v:18mA
-12v:18mA
+5v: 600mA

Notes: Polydactyl Versio is Noise Engineering's take on a multiband dynamics processor. Polydactyl Versio is equally at home on single-instrument timbral processing and on end-of-chain gloss. Taking inspiration from Noise Engineering's Librae Legio, Polydactyl Versio applies a unique and transparent algorithm across three bands for maximal dynamic impact. Add in a multiband saturation knob and noise gate, throw in a limiter, and you have a processor that gives ultimate control of color and dynamics.

Polydactyl Versio is part of the Versio family: this platform module can be transformed into a completely different effect by loading a growing number of alternate firmwares, completely free! Plus, with open-source support and documentation at LibDaisy, you can write your own firmware. Grab a Polydactyl Versio and process your signal into submission or total rebellion with three separate bands, saturation, limiting, and noise gating.

Size and power:
10 HP
+12v: 125ma
-12v: 10ma
+5v: 0ma