100% Secure Shopping

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Secure Shopping

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

View:
Options
Items 1 to 50 of 788 on page 1 of 16
1  2  3  ...  16  »
FORTHCOMING
Doepfer A-111-6 Miniature Synthesiser Voice Module (vintage edition)
Cat: 749811 Rel: 31 Oct 19
 
Complete miniature monophonic synthesiser module - 10HP
Notes: VCO:

- Tune: manual tune control (with an internal jumper the range can be set to ~ +/-1 half an octave or ~ +/-2.5 octaves)
- Oct: range switch -1 / 0 / +1 octave
- Mod: modulation depth (attenuator wired to the Mod. socket)
- Dest: switch that is used to address the modulation to frequency modulation (position FM) or pulsewidth modulation (positon PM), in centre positon no modulation
- PW: manual pulsewidth control for rectangle waveform, PW can be also modulated by the Mod. input as mentioned above
- Wave: waveform switch (sawtooth / off / triangle), the sum of the waveform chosen by this switch and the rectangle is fed into the VCF (to turn the rectangle off the PW control has to be set fully CCW or fully CW)
- 1V/Oct. (socket): external CV input for VCO frequency (1V/octave)
- Access to internal bus CV (via jumper, optional, please remove the bus jumper if this feature is not used to avoid unwanted frequency modulation as then the unused CV line of the bus works as a kind of antenna)
- Triangle core VCO, frequency range about 32Hz ... 8kHz

Balance unit:

- The balance unit is made of two VCAs which are controlled by the sum of manual Balance control and the balance CV input in the opposite direction.
- The audio input of VCA1 is hard-wired to the VCO output, audio input 2 is connected to the socket Ext.In.
- The output of the balance unit is used as audio input for the VCF
- Bal.: manual balance control, fully CCW the internal VCO is used, fully CW the external signal (Ext.In) is used, at centre position both signals have about the same level
- CV Bal.: CV input for balance (range about 0...+5V)
- Ext. In: external audio input for VCA2, about 5 Vpp level required for similar loudness as the internal VCO
- This socket is normalled to the internal VCO suboctave f/2 signal (rectangle with half the frequency), if no external signal is applied the suboctave signal is used as the second signal for the balance unit

VCF:

- 24 dB low pass
- Frq: manual frequency control
- FM1: frequency modulation depth (attenuator wired to the VCF FM1 socket, the socket is normalled to the internal Envelope signal and then FM1 controls the modulation depth of the internal envelope applied to the filter)
- FM2 (socket) : second CV input for VCF without attenuator (about 1V/octave), can be used e.g. for VCF tracking by connecting the same CV which is used also for the VCO frequency
- Res: manual resonance control (up to self oscillation)
- If the VCO is turned off (waveform switch = centre position, pulsewidth control = fully CCW or CW) and the VCF resonance is set to maximum the module can be used as a sine oscillator, the tracking at socket VCF FM2 is about 1V/octave (not as precise as the VCO but much better than most other filters)
- ~ 11 octaves frequency range (~ 10 Hz ... 20kHz)

VCA:

- Gain: manual amplitude control (initial gain), can be used to open the VCA without envelope signal
- VCA (switch): used to switch between gate and envelope as control signal for the VCA, in centre position the VCA is not controlled by envelope or gate
- Note: when gate is used the VCA is controlled directly by the gate signal (i.e. hard on/off), this may lead to clicking noise under certain conditions (especially with low VCO/VCF frequencies)
- Special control scale: exponential scale in the range from about -20dB to -80/90dB, linear scale from about -20dB to 0dB
- Remark: this special control scale results in a loudness behaviour that is a bit different from pure linear or exponential VCAs
- Out: audio output of the module (= VCA output)

Envelope:

- Gate (socket): Gate input (min. +5V), can be normalled to the bus gate signal by means of a jumper
- Att: manual control for Attack
- D/R: manual control for Decay/Release
- Env. (switch): used to switch between A/D, ADSR and A/R mode of the envelope generator, in centre position (ADSR) the sustain level is fixed to about 50%
- Envelope (socket): envelope output (about +10V)
- CVT (socket): CV input for time control, by means of two internal jumpers one can select which time parameters are controlled by the CVT input (e.g. A only or D/R only or A/D/R) and in which direction (i.e. if an increasing CVT shortens or stretches the time parameter in question)
- Envelope LED display
- Attack time range: ~ 1ms ... 5 sec (can be extended by using the CVT input)
- Decay/Release time range: ~ 1ms ... 15 sec (can be extended by using the CVT input)
Read more
coming soon $184.98
FORTHCOMING
Flame Panmix Dual Panning Recorder Module
Cat: 749823 Rel: 31 Oct 19
 
Dual channel stereo panner with automation
Notes: The FLAME "PANMIX" module contains two independent panning mixers with one input each on two outputs left/right and is designed for audio or CV sources in the voltage range +-5v (audio modular level). In addition, the 2 inputs can be switched separately to +6db audio (for external audio line level sources) using the slide switch on the rear panel.

The movements of the two mix controls can be recorded. The recording time per channel is more than one minute. The playback speed can be adjusted in playback. The recorded track is played back once when the Play button is pressed briefly (one shot) or in the loop when the button is pressed a little longer.

Both panning channels have a separate reset input as well as a separate CV input (+-5V ) for controlling the mix e.g. by an LFO. The track data remains permanently stored (battery buffered memory).

In addition, there are three further audio/CV signal inputs (a mono and stereo left+right), which are routed directly to the output and mixed together with the two PAN channels. This allows you to mix in other sources directly and e.g. connect two or more "PANMIX" modules together.
Read more
coming soon $204.45
FORTHCOMING
TouellSkouarn Ar Merc'het Brao Dual Filter & Overdrive Module
coming soon $373.20
FORTHCOMING
4ms Listen Up Passive Expander Module For Listen Modules
coming soon $65.98
FORTHCOMING
4ms Row Power 25 Power Solution For Eurorack Systems (white)
coming soon $100.59
FORTHCOMING
4ms Pod 32 Beta Unpowered Eurorack Module Enclosure Case
coming soon $26.77
FORTHCOMING
Doepfer A-180-2v Multiples Module (vintage edition) Doepfer A-180-2v Multiples Module (vintage edition) Doepfer A-180-2v Multiples Module (vintage edition)
Cat: 751717 Rel: 23 Oct 19
 
Passive multi-port distributor - 2HP
Notes: 2HP narrow version of the A-180 multiples module. It is a passive signal splitter suitable for audio or CVs. Two sets of four jacks are interconnected, by placing a solder bridge you can connect all eight jacks.
Read more
coming soon $38.40
FORTHCOMING
Doepfer A-183-1 Dual Attenuator Module Doepfer A-183-1 Dual Attenuator Module Doepfer A-183-1 Dual Attenuator Module
Cat: 751728 Rel: 23 Oct 19
 
Dual passive attenuator - 4HP
Notes: Module A-183-1 is a simple passive dual attenuator. Passive means, that each unit is made of two sockets and a 50k linear potentiometer only. There are no active parts like amplifiers or buffers and no power supply is required.

This is how the A-183-1 works: At the output socket appears the attenuated input signal, i.e. zero level at the fully CCW position and max. level and the fully CW position.

Applications:

Adjustable level of CV or audio signals to control other modules that do not have attenuators (e.g. Dual VCA A-132-1, Quantizer A-156, CV-to-Midi interface A-192 and modules of other manufacturers).
Read more
coming soon $40.02
FORTHCOMING
Doepfer A-185-2 Precision Control Voltage Adder & Buffer Module Doepfer A-185-2 Precision Control Voltage Adder & Buffer Module Doepfer A-185-2 Precision Control Voltage Adder & Buffer Module
Cat: 751763 Rel: 23 Oct 19
 
Precision adder (mixer) and buffer for control voltages - 6HP
Notes: Module A-185-2 is a precision control voltage adder/buffer. Precision means that the amplification of the inputs without attenuators is exactly 1.00 and is suitable to add control voltages for the pitch control of VCOs (e.g. from keyboard + sequencer 1 + sequencer 2). Summing resistors matched to 0.1% are used to obtain an accuracy of 0.1% for the added voltages.

The module is equipped with four CV inputs: one with attenuator and three without attenuator. Each input is normalled to +1 V (i.e. if no plug is inserted the input contributes 1 V to the sum appearing at the output).

The input with attenuator can be used for common modulations (e.g. from an LFO, ADSR, Theremin, Pitch-Bender) for all VCOs connected to the output. The Lev.1 control is used to adjust the depth of the modulation, the first switch selects the polarity of the modulation. If no signal is connected to the first socket the attenuator works as a (fine) tuning knob because a voltage in the range 0...+1V (right position of the switch) or 0...-1V (left position of the switch) is added to the CV output.

The inputs without attenuators are planned to add control voltages coming out of keyboards, sequencers, Midi-to-CV interfaces, ribbon controllers or other CV sources that follow the 1V/oct standard. For example the CV of a keyboard can be used to transpose the CV coming from a sequencer, or the CV of a slow sequencer can be used to transpose the CV from a fast sequencer.

Each input is equipped with a three-position switch that determines if the corresponding voltage is added (right position), subtracted (left position) or if the input has no effect (centre position). If no plug is inserted the corresponding switch works as an octave switch for the lower three sections as the default 1 V are added or subtracted to the output voltage according to the switch position. The first switch can be used to add a variable voltage to the sum output. The variable voltage is adjusted with the Lev.1 control and the knob works then as kind of a (fine) tuning control.

The module is equipped with 4 outputs: three non-inverting and one inverting ouput. An internal jumper can be used to connect the non-inverted or inverted output to the CV line of the A-100 bus. That way the module can used to control several VCOs that are connected to the same bus board as the A-185-2 (same functionality as A-185-1).
Read more
coming soon $72.48
FORTHCOMING
Doepfer A-185-2v Precision Control Voltage Adder & Buffer Module (vintage edition) Doepfer A-185-2v Precision Control Voltage Adder & Buffer Module (vintage edition) Doepfer A-185-2v Precision Control Voltage Adder & Buffer Module (vintage edition)
Cat: 751764 Rel: 23 Oct 19
 
Precision adder (mixer) and buffer for control voltages - 6HP
Notes: Module A-185-2 is a precision control voltage adder/buffer. Precision means that the amplification of the inputs without attenuators is exactly 1.00 and is suitable to add control voltages for the pitch control of VCOs (e.g. from keyboard + sequencer 1 + sequencer 2). Summing resistors matched to 0.1% are used to obtain an accuracy of 0.1% for the added voltages.

The module is equipped with four CV inputs: one with attenuator and three without attenuator. Each input is normalled to +1 V (i.e. if no plug is inserted the input contributes 1 V to the sum appearing at the output).

The input with attenuator can be used for common modulations (e.g. from an LFO, ADSR, Theremin, Pitch-Bender) for all VCOs connected to the output. The Lev.1 control is used to adjust the depth of the modulation, the first switch selects the polarity of the modulation. If no signal is connected to the first socket the attenuator works as a (fine) tuning knob because a voltage in the range 0...+1V (right position of the switch) or 0...-1V (left position of the switch) is added to the CV output.

The inputs without attenuators are planned to add control voltages coming out of keyboards, sequencers, Midi-to-CV interfaces, ribbon controllers or other CV sources that follow the 1V/oct standard. For example the CV of a keyboard can be used to transpose the CV coming from a sequencer, or the CV of a slow sequencer can be used to transpose the CV from a fast sequencer.

Each input is equipped with a three-position switch that determines if the corresponding voltage is added (right position), subtracted (left position) or if the input has no effect (centre position). If no plug is inserted the corresponding switch works as an octave switch for the lower three sections as the default 1 V are added or subtracted to the output voltage according to the switch position. The first switch can be used to add a variable voltage to the sum output. The variable voltage is adjusted with the Lev.1 control and the knob works then as kind of a (fine) tuning control.

The module is equipped with 4 outputs: three non-inverting and one inverting ouput. An internal jumper can be used to connect the non-inverted or inverted output to the CV line of the A-100 bus. That way the module can used to control several VCOs that are connected to the same bus board as the A-185-2 (same functionality as A-185-1).
Read more
coming soon $80.05
FORTHCOMING
Doepfer A-184-1v Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module (vintage edition) Doepfer A-184-1v Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module (vintage edition) Doepfer A-184-1v Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module (vintage edition)
Cat: 751757 Rel: 23 Oct 19
 
4HP Eurorack module featuring a combination of 3 functions
Notes: Module A-184-1 is the combination of three functions:

- Ring Modulator
- Sample&Hold/Track&Hold unit
- Slew Limiter

The same functions are actually already available in other modules (e.g. A-114, A-148, A-170). But in many systems it's not necessary to have two ring modulators (A-114) or two S&H units (A-148) or two slew limiters (A-170) available. That's why we have compiled these function in one small 4 HP module.

The upper section is nothing but half of an A-114, i.e. a ring modulator with the usual X/Y inputs and the X*Y output. Inputs and outputs of this sub-unit are AC coupled, i.e. suitable only for audio signals. A detailed explanation of a ring modulator can be found on the A-114 info page.

The lower section is a Sample & Hold (S&H) / Track & Hold (T&H) unit (same as half of an A-148) followed by a slew limiter (same as the upper section the A-170). A toggle switch is used to set the mode to S&H or T&H. In S&H mode the unit picks out a sample from the voltage at the SH input at the rising edge of the trigger signal input. In T&H mode the output follows the input voltage as long as the level of the trigger signal is high. As soon as the trigger signal turns low, the last voltage is stored. The trigger input is internally normalled to high, i.e. the unit works just as a slew limiter in T&H mode when no trigger signal is applied.
Read more
coming soon $107.09
FORTHCOMING
Doepfer A-184-2 Voltage Controlled Crossfader & Triangle To Sine Waveshaper Module Doepfer A-184-2 Voltage Controlled Crossfader & Triangle To Sine Waveshaper Module Doepfer A-184-2 Voltage Controlled Crossfader & Triangle To Sine Waveshaper Module
Cat: 751758 Rel: 23 Oct 19
 
Sine converter/VC crossfader - 4HP
Notes: Module A-184-2 is the combination of two functions and planned primarily as an expansion module for VCOs or LFOs (e.g. A-110-1, A-110-2, A-145, A-147-2).

Triangle-to-Sine Waveshaper:

The upper section is a very precise triangle-to-sine converter (thanks to Tim Stinchcombe who recommended this circuit). It can be used to convert any triangle waveform into a (nearly) perfect sine. The converter is much better than the simple diode converter used in the A-110-1, A-111-1, A-145 and A-147-2. Two trimming potentiometers are used to optimize the sine shape. The converter should be assigned to one VCO or LFO because the trimming potentiometers have to be re-adjusted if the input level or DC offset of the input signal changes. If the trimming potentiometers are deliberately mis-adjusted it can be used also as a waveshaper for non-sine waveforms (e.g. sine-shaped at the top of the signal and a peak at the bottom, even voltage controlled by applying an additional voltage to the waveshaping circuit, "circuit-bending" notes will be available).

The waveform converter is DC coupled and can be used also for low frequencies (e.g. LFO triangle waves).

Voltage Controlled Crossfader:

The lower section is a voltage controlled crossfader. It has two inputs A and B. The two signals are mixed together with variable percentage. When the manual control CF is fully CCW only signal A appears at the CF Out socket. When the manual control CF is fully CW only signal B appears at the CF Out socket. In the centre position of the manual control both signal appear with the same level. In addition a control voltage input CV with attenuator is available to enable voltage control of the crossfade.

Two LEDs display the crossfading shares of input A and B.

The crossfader uses two high quality VCAs (SSM2164). Inputs and outputs are DC coupled. Consequently it can be used for audio signals and slowly varying control voltages as well.

The sockets of the upper section (triangle and sine) are normalled to the inputs A and B of the crossfader section. That way the crossfader is used to fade between triangle and sine of the VCO or LFO connected to the waveshaper. If other signals are plugged into the input sockets A and B these signals are used for crossfading.

The main application is to fade between two different waveforms of a VCO or LFO or two different VCF outputs. But the module can be used for any other signals too as the waveshaper and crossfader sections are independent apart from the normalled sockets.
Read more
coming soon $81.67
FORTHCOMING
Doepfer A-185-1 Active Bus Access Module
Cat: 751760 Rel: 23 Oct 19
 
Provides input & output access to your Eurorack's internal CV/Gate bus
Notes: Active bus access module to feed CV and Gate into the A-100 bus (e.g. when using more than one frame or with external CV/Gate interfaces). Miniature jack sockets for CV In, Gate In, 2xCV Out, 2xGate Out, 2 LEDs for CV/Gate control

In general, the A-185 is recommended as soon as more than 2 VCO's (A-110, A-111) are controlled by the same control voltage source. Without interconnection of the A-185 in this case tuning inaccuracies (scale) may occur. The A-185 is mounted close to the VCOs. The controlling voltage for all VCOs is applied to the CV In socket of the A-185. By means of the CV line of the bus board the CV is connected to all VCOs at the same bus board.
Read more
coming soon $53.01
FORTHCOMING
Doepfer A-187-1 Voltage Controlled DSP Effects Module
Cat: 751766 Rel: 23 Oct 19
 
DSP based effects module - 18HP
Notes: Module A-187-1 is a DSP based effects module. Four parameters of the selected digital effect are voltage controlled. The main effect (e.g. reverb, delay, pitch-shifter, equalizer) is selected by the two small buttons effect up/down. The upper row of the display shows the effect that is currently selected. In the lower row the four parameters are shown as well as a small bar left from the abbreviation that displays the current parameter value. Each parameter can be adjusted manually (upper potentiometer row) and modified by external control voltages (lower row of the potentiometers and upper row of the sockets). The lower row of the sockets contains the two audio inputs and outputs.

Another button (bypass) is used to turn the effect on/off. When bypass is chosen the upper line of the display shows in turn "BYPASS" and the name of the pre-selected effect. In the bypass mode another effect can be pre-selected and called-up by pressing the bypass button again. Even the effect parameters can be adjusted and are displayed with the bar graphs. But they become effective not before the bypass mode is left.

The module is equipped with two audio inputs and two audio outputs because the DSP board features stereo audio processing. The audio inputs can process usual A-100 signal levels without clipping/distortion. For higher levels external attenuators (e.g. A-183-1) or VCAs may be used.

A ready-made DSP board is used inside the A-187-1 module. Consequently, only these effects and parameters are available that are supported by the DSP module. Some parameters can be changed only in steps or with audible artefacts. The DSP board has 20 Bit DA and AD converter with 32 kHz sample rate available. The inter sound processing uses 24 Bit.
Read more
coming soon $262.87
FORTHCOMING
Doepfer A-170 Dual Slew Limiter Module Doepfer A-170 Dual Slew Limiter Module Doepfer A-170 Dual Slew Limiter Module
Cat: 751699 Rel: 23 Oct 19
 
Two separate slew limiters for generating portamento effects - 8HP
Notes: Module A-170 contains two separate slew limiters, also known as portamento controllers or integrators. The first SL has just one joint control, which sets both rise and fall times (c. 0 ...10 sec). The second SL has separate controls for rise and fall times, and can therefore be used as a simple AR envelope generator. Over and above this, you can set the overall range for these parameters, with a three-position switch, as on the full ADSRs.

Both slew limiters have two LEDs each, to show the state of the rising and falling voltages.


Additional technical remarks: If the upper slew limiter is used for precision applications (e.g. portamento/glide of one or more VCOs) a buffer (e.g. A-185-1 or A-185-2) is recommended between the A-170 output and the VCO(s) input(s). The reason is a small voltage drop that is caused by the protection resistor at the A-170 output. An A-185-1 or A-185-2 connected between the A-170 and the VCO(s) avoids that voltage loss. For all A-170 manufactured later than May 2009 (recognizable by the label "Version 2" on the pc board) this remark is not valid as these modules are equipped with an additional voltage buffer at the output.

The lower slew limiter cannot be used for precision applications because of the voltage loss caused by the diodes of the circuit.
Read more
coming soon $62.74
FORTHCOMING
Doepfer A-175 Dual Voltage Inverter Module Doepfer A-175 Dual Voltage Inverter Module Doepfer A-175 Dual Voltage Inverter Module
Cat: 751709 Rel: 23 Oct 19
 
Two identical inverters - 4HP
Notes: Module A-175 (Dual Voltage Inverter) is exactly what it says it is: two identical inverters, which will take a voltage and output it in an inverted form - so that an input of +5 V will be output as -5 V, an input of -2 V will be output as +2 V, and so on. Two LEDs give a visual indication of the (positive or negative) output signal.
Read more
coming soon $53.01
FORTHCOMING
Doepfer A-176 Control Voltage Source Module Doepfer A-176 Control Voltage Source Module Doepfer A-176 Control Voltage Source Module
Cat: 751711 Rel: 23 Oct 19
 
Three independent voltage sources - 8HP
Notes: Module A-176 (Control Voltage Source) provides three voltage sources, to use wherever an extra CV is required. The top two voltage sources (CV 1 and CV 2) have controls for coarse and fine control of the voltage output; the third source (CV 3) just has the one control.

The range of the voltages output can be preset, either to 0 to +5 V or to -2.5 V to +2.5 V depending on your likely requirements. There is a jumper on the circuit board for each of the three voltage sources.

A typical use for the module would be to provide fine as well as coarse tuning for an A-110 standard VCO, (which, unlike the A-111, only has one tune control).

In general, this module will be useful whenever you need a manually controllable CV on a module which doesn't itself have a built-in control.
Read more
coming soon $62.74
FORTHCOMING
Doepfer A-186-1 Gate & Trigger Combiner & Rectifier Module Doepfer A-186-1 Gate & Trigger Combiner & Rectifier Module Doepfer A-186-1 Gate & Trigger Combiner & Rectifier Module
Cat: 751765 Rel: 23 Oct 19
 
Gate/trigger combiner - 4HP
Notes: Module A-186-1 is a very simple, passive unit that combines up to 7 gate, trigger or analog signals by or-wiring.

Function:

- If all seven inputs are low or open the output is low
- If one or more of the seven inputs is "high" the output turns high

Applications:

- Combination ("or"-wiring) of gate and/or trigger signals (e.g. from LFOs, sequencers, keyboards, Midi-to-CV interfaces, ribbon controller, theremin, trigger delays or any other source of gate/trigger signals
- Maximum extractor for analog voltages: at the output the maximum voltage (minus ~ 0.7V because of the diodes) appears, similar function as the maximum output of the A-172 Maximum/Minimum Selector module, e.g. for simple waveshaping
- Simple half-wave rectifier
Read more
coming soon $45.43
FORTHCOMING
Doepfer A-171-2v Voltage Controlled Slew Processor & Generator Module (vintage edition) Doepfer A-171-2v Voltage Controlled Slew Processor & Generator Module (vintage edition) Doepfer A-171-2v Voltage Controlled Slew Processor & Generator Module (vintage edition)
Cat: 751704 Rel: 23 Oct 19
 
Slew processor/generator - 8HP
Notes: Module A-171-2 is a voltage controlled slew limiter with a lot of additional features beyond a simple slew limiter. It's mostly a licensed copy of Ken Stones VCS which is in turn based on the Serge VCS.

Typical applications:

- VC Slew Limiter / VC Portamento / VC Low Pass Gate:

Cycle switch = off, no trigger signal applied to Trig socket: Voltage controlled Slew limiter or portamento generator: the signal applied to the signal input is "slewed". The slew up and down times are controlled manually by means of the Up and Down controls, the effect of the CV Up and CV Down control voltages are controlled by the CV Up and CV Down controls, in exponential mode these controls also affect the slew shape (see symbols at the CCW and CW positions of the controls).

If an audio signal is applied an short slew rates are chosen the module works as a simple VCF/VCA combo.

- A/D Envelope Generator / Pulse Delay / Subharmonic Generator:

Cycle switch = off, trigger signal applied to Trig socket, no input signal: Simple Attack/Decay envelope Generator, the rise and fall times are controlled like the slew up/down times above, including the shape of the falling/rising slope of the envelope, the exp. CV input can be used to change both attack and decay simultaneously.

At the End output a pulse appears as the end of the envelope is reached (less than about 20mV), this can be used as a pulse delay.

If a series of triggers are applied to the VCS faster than the total rise and fall times, the module will divide the incoming signal by a whole number. In the audio range the output will be the sub-harmonic series.

- VCLFO / VCO:

Cycle switch = on, no trigger signal applied to Trig socket, no input signal: Voltage controlled LFO/VCO, the rise and fall times of the waveform are controlled like the slew up/down times above, including the shape of the falling/rising slope
the exp. CV input can be used like the CV input of a VCO or VCLFO, the response is exponential but not exactly 1V/oct.
Read more
coming soon $136.30
FORTHCOMING
Doepfer A-183-2 Voltage Offset Generator & Attenuator/Polarizer Module Doepfer A-183-2 Voltage Offset Generator & Attenuator/Polarizer Module Doepfer A-183-2 Voltage Offset Generator & Attenuator/Polarizer Module
Cat: 751731 Rel: 23 Oct 19
 
Compact module for attenuating control voltage signals - 4HP
Notes: Module A-183-2 is a voltage offset generator combined with an attenuator/polarizer.

This is how the A-183-2 works: At the two output sockets (simply two connected sockets) appears a DC voltage that is adjusted with the Offset control in the range 0...+5V or -5V...+5V. An internal jumper is used to select the offset range (0...+5V or -5V...+5V). Other ranges are possible by changing a resistor on the pc board (e.g. 0...+10V or -10V...+10V). The DC voltage generated by the Offset control is overlaid by the attenuated voltage that is fed to the In socket. The function of the attenuator control can be set to Attenuator or Polarizer by means of a toggle switch. When the switch is in the Attenuator position the control works as an usual attenuator, i.e. zero level at the fully CCW position and max. level and the fully CW position. When the switch is in the Polarizer position the control works as a polarizer, i.e. zero level appears at the centre position. Right from the centre position the In signal is added to the offset voltage, left from the centre position the In signal is subtracted from the offset voltage. In other words: at the fully CW position the non-inverted In signal is added with the full level to the offset voltage, at the fully CCW position the inverted In signal is added with the full level to the offset voltage.

The amplification range for the input is about 0...+1 in the attenuator mode, and -1...+1 in the polarizer mode. The amplification range can be modified by replacing a resistor by another value.

Applications:

Generation of adjustable DC voltages overlaid by control voltages with adjustable level and polarity to control other modules that do not have attenuators or offset controls, e.g. Sampler A-112 (mainly for the wavetable mode), dual VCA A-132-1, VCLFO A-147-2 for waveshaping and ring modulator applications, Quantizer A-156, Theremin A-178, CV-to-Midi interface A-192 and modules of other manufacturers).
Read more
coming soon $45.43
FORTHCOMING
Doepfer A-183-3 Amplifier Module Doepfer A-183-3 Amplifier Module Doepfer A-183-3 Amplifier Module
Cat: 751740 Rel: 23 Oct 19
 
DC coupled amplifier - 4HP
Notes: Module A-183-3 is a simple amplifier. It is DC coupled and can be used for both CV and audio signals. The maximal amplification can be switched between 1, 2 and 4 (in position 1 the module does not work as a real amplifier but only as attenuator). The level can be adjusted by means of the Level control between zero and the chosen maximum amplification (1/2/4). Two overload LEDs indicate if the output signal goes beyond about +10V or becomes less than about -10V. Input and output are equipped with miniature 2-fold multiples (nothing but 2 connected sockets).

The main application of this module is to adapt differing audio or CV levels between different modules or systems. For example, LFO, ADSR or Gate levels between modules of different manufacturers can be increased or attenuated. But even audio signals can be attenuated or amplified up to 4. But the module cannot be used as an amplifier for external low level audio signals (e.g. microphones or electric guitars)!
Read more
coming soon $44.35
FORTHCOMING
Doepfer A-180-3 Dual Buffered Multiple Module Doepfer A-180-3 Dual Buffered Multiple Module Doepfer A-180-3 Dual Buffered Multiple Module
Cat: 751720 Rel: 23 Oct 19
 
Dual buffered 1-in-3 multiple module - 4HP
Notes: Module A-180-3 is a dual buffered 1-in-3 multiple. The signal applied to the input socket appears as a buffered signal at the three output sockets. Each output has its own buffer, i.e. the three output sockets are not simply connected to each other. The lower output of the upper unit is normalled in the factory to the input of the lower unit. That way the module works as a single 1-in-6 buffered multiple provided that no signal is applied to the input of the lower unit. But it's also possible to pick-up the bus CV and normalize the input socket of the lower unit to the bus CV.

Application: copying/buffering of CV, gate and audio signals.
Read more
coming soon $49.76
FORTHCOMING
Doepfer A-170v Dual Slew Limiter Module (vintage edition) Doepfer A-170v Dual Slew Limiter Module (vintage edition) Doepfer A-170v Dual Slew Limiter Module (vintage edition)
Cat: 751702 Rel: 23 Oct 19
 
Two separate slew limiters for generating portamento effects - 8HP
Notes: Module A-170 contains two separate slew limiters, also known as portamento controllers or integrators. The first SL has just one joint control, which sets both rise and fall times (c. 0 ...10 sec). The second SL has separate controls for rise and fall times, and can therefore be used as a simple AR envelope generator. Over and above this, you can set the overall range for these parameters, with a three-position switch, as on the full ADSRs.

Both slew limiters have two LEDs each, to show the state of the rising and falling voltages.


Additional technical remarks: If the upper slew limiter is used for precision applications (e.g. portamento/glide of one or more VCOs) a buffer (e.g. A-185-1 or A-185-2) is recommended between the A-170 output and the VCO(s) input(s). The reason is a small voltage drop that is caused by the protection resistor at the A-170 output. An A-185-1 or A-185-2 connected between the A-170 and the VCO(s) avoids that voltage loss. For all A-170 manufactured later than May 2009 (recognizable by the label "Version 2" on the pc board) this remark is not valid as these modules are equipped with an additional voltage buffer at the output.

The lower slew limiter cannot be used for precision applications because of the voltage loss caused by the diodes of the circuit.
Read more
coming soon $77.89
FORTHCOMING
Doepfer A-172 Maximum/Minimum Selector & Rectifier Module Doepfer A-172 Maximum/Minimum Selector & Rectifier Module Doepfer A-172 Maximum/Minimum Selector & Rectifier Module
Cat: 751706 Rel: 23 Oct 19
 
Module for processing/mixing of control voltages - 4HP
Notes: A-172 is a minimum/maximum selector module and is equipped with four analogue inputs and two analogue outputs (minimum, maximum). The main application of the module is the processing/mixing of control voltages, e.g. random voltages, ADSR, LFO, S&H, ribbon CV, theremin-CV and similar, but even for audio signal processing the module can be used (e.g. several outputs of the same or different VCOs).

The module permanently picks the maximum resp. minimum voltage out of the four input signals and outputs these voltages to the maximum resp. minimum jack socket.

To adjust offset and amplitude for each input independently (i.e. to bring the signal into the right "position" with the desired level) we recommend combining the module with the A-129-3 Slew Limiter/Attenuator/Offset Generator (see patch example below). The other sketch below shows the basic principle of the max/min module by means of three sine waves (e.g. three LFOs) with different frequencies and different levels.

The module can be used also as a simple half-wave rectifier.
Read more
coming soon $51.11
FORTHCOMING
Doepfer A-174-2 Modulation Wheels CV Source Module Doepfer A-174-2 Modulation Wheels CV Source Module Doepfer A-174-2 Modulation Wheels CV Source Module
Cat: 751707 Rel: 23 Oct 19
 
Modulation wheel module with two wheels - 14HP
Notes: A-174-2 is a modulation wheel module with two wheels. The factory setting is a spring loaded wheel at the left side with bipolar voltage output (i.e. 0V in centre position, positive voltage in the upper range, negative voltage in the lower range, voltage range about -5.5 V ... 0V ... +5.5 V) and a wheel without spring at the right side with positive voltage output (i.e. 0V in the lowest position and positive voltage when operated, voltage range about 0...+8 V). For the spring loaded wheel a voltage "plateau" around 0 V is preset (jumper) so that the output voltage is 0 V in a small area near the centre position.

By means of jumpers the factory settings can be changed. For each wheel two jumpers are available: one for the voltage range (positive or bipolar) and one for the voltage plateau around 0 V. If these settings are changed even the wheels have to be re-adjusted mechanically. Therefore, such modifications should be carried out by a qualified person only. By request the module is available from the factory even with two wheels both with or without springs (additional charges Euro 10.00 for each change).

Important note for module mounting: As the potentiometer of the left wheel projects about 10 mm the rim of the front panel a 2 or 4 HP blind panel has to be mounted left from the module - unless the module left to the A-174-1 has sufficient space in this area (e.g. A-174-1).
Read more
coming soon $77.89
FORTHCOMING
Doepfer A-177-2 External Foot Controller II Module Doepfer A-177-2 External Foot Controller II Module Doepfer A-177-2 External Foot Controller II Module
Cat: 751715 Rel: 23 Oct 19
 
Foot controller interface - 8HP
Notes: Economically priced module for connecting one foot controller and one double foot switch for control A-100 functions by means of the feet. For example, the frequency of a filter or the loudness can be controlled by a foot controller, but even other parameters like LFO frequency, modulation depth, phasing, pitch or any other voltage controlled parameter. The gate outputs controlled by the double foot switch can be used e.g. to trigger an envelope generator or to start/stop a sequencer. Even a single foot switch can be used if only one gate signal is required.

A special application of the A-177-2 is the usage within a Trautonium replica. The foot switches can be used to switch the mixtures of the subharmonic oscillator A-113. The foot controller can be used to control the overall loudness in combination with a VCA.

A-177 is compatible with the foot controllers FP5 and double foot switch VFP2. The Foot controller and double foot switch are not included with the module. If you want to use another foot controller or foot switch it has to be compatible to FP5 or VFP2.

If the foot controller FP5 is used the CV output range is about 0...+8V. The gate output levels are 0/+12V in combination with the VFP2 (foot switch not operated = 0V, foot switch operated = +12V).
Read more
coming soon $53.01
FORTHCOMING
Doepfer A-178 Theremin Control Voltage Source Module Doepfer A-178 Theremin Control Voltage Source Module Doepfer A-178 Theremin Control Voltage Source Module Doepfer A-178 Theremin Control Voltage Source Module
Cat: 751716 Rel: 23 Oct 19
 
Theremin controller module - 8HP
Notes: Theremin module for generating a variable control voltage by approaching/removing hand to/from an antenna. The distance range is about 30-40 cm. Additionally the module is equipped with a Gate output with adjustable threshold level. Controls/Inputs/Outputs: antenna input, offset (knob for zero adjust), 2 x CV out, 2 x LED (for CV control positive/negative and zero offset adjust).

To simulate the original Theremin two A-178, a VCO (e.g. A-110) and a linear VCA (e.g. A-130 or A-132) are required. But of course the A-178 can be used to control other functions in the A-100 (e.g. filter frequency, modulation depth and/or speed, tempo, attack/decay time and so on).

The CV output voltage of the A-178 can range - according to the setting of the front panel controls - from -10V...+10V. The gate output switches from 0V to about +10V.

Applications:

- Controlling any voltage controlled parameter of the A-100, e.g. pitch or pulsewidth (VCO A-110), loudness (VCA A-130/131/132), panorama (A-134), filter frequency or resonance (A-120/121/122/123), phasing (A-125), frequency shift (A-126), resonance peaks (A-127), envelope parameters (A-141/142), tempo (A-147)

- Triggering of A-100 activities via gate with adjustable threshold, e.g. starting an envelope (A-140/141/142), Start/Stop of a sequence (A-155), any switching function (A-150/151)

- Conversion into MIDI control change messages is possible with the A-192.

If two or more A-178 are used the distance between the modules/antennas should be at least 40-50 cm. Otherwise the antennas may affect each other.
Read more
coming soon $96.28
FORTHCOMING
Doepfer A-181 Multiples 2 Module Doepfer A-181 Multiples 2 Module Doepfer A-181 Multiples 2 Module
Cat: 751722 Rel: 23 Oct 19
 
Two multiples with one 1/4 jack socket & two 3.5mm jack sockets each
Notes: Doepfer's A-181 Multiples 2 is a simple multiple and cable format converter, suitable for translating 1/4" signals to 1/8" and vice versa. The upper mult is wired for monophonic signals, while the lower mult features a 1/4" stereo connector which offers direct 1/8" connection to the tip and ring, respectively, allowing use as a stereo splitter or dual 1/8" to stereo 1/4" converter.
Read more
coming soon $45.43
FORTHCOMING
Doepfer A-182-1 Switched Multiples Module Doepfer A-182-1 Switched Multiples Module Doepfer A-182-1 Switched Multiples Module
Cat: 751724 Rel: 23 Oct 19
 
Eurorack passive multi-connector - 6HP
Notes: Module A-182-1 is a simple passive multi-connector similar to the multiples modules A-180-1/A-180-2. In contrast to modules A-180-1/2 each socket is equipped with a 3-position switch that allows to connect the corresponding socket to the internal bus #1 (left position), bus #2 (right position) or to turn the socket off (centre position).

Examples:

- All switches in left position or all switches in right position: 8-fold multiple

- Four switches in left position and four switches in right position: two 4-fold multiple

- X switches in left position, Y switches in right position and Z switches in centre position: two separate multiples with some sockets turned off
Read more
coming soon $53.01
FORTHCOMING
Doepfer A-184-1 Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module Doepfer A-184-1 Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module Doepfer A-184-1 Ring Modulator, Sample & Hold, Track & Hold, & Slew Limiter Module
Cat: 751756 Rel: 23 Oct 19
 
4HP Eurorack module featuring a combination of 3 functions
Notes: Module A-184-1 is the combination of three functions:

- Ring Modulator
- Sample&Hold/Track&Hold unit
- Slew Limiter

The same functions are actually already available in other modules (e.g. A-114, A-148, A-170). But in many systems it's not necessary to have two ring modulators (A-114) or two S&H units (A-148) or two slew limiters (A-170) available. That's why we have compiled these function in one small 4 HP module.

The upper section is nothing but half of an A-114, i.e. a ring modulator with the usual X/Y inputs and the X*Y output. Inputs and outputs of this sub-unit are AC coupled, i.e. suitable only for audio signals. A detailed explanation of a ring modulator can be found on the A-114 info page.

The lower section is a Sample & Hold (S&H) / Track & Hold (T&H) unit (same as half of an A-148) followed by a slew limiter (same as the upper section the A-170). A toggle switch is used to set the mode to S&H or T&H. In S&H mode the unit picks out a sample from the voltage at the SH input at the rising edge of the trigger signal input. In T&H mode the output follows the input voltage as long as the level of the trigger signal is high. As soon as the trigger signal turns low, the last voltage is stored. The trigger input is internally normalled to high, i.e. the unit works just as a slew limiter in T&H mode when no trigger signal is applied.
Read more
coming soon $96.28
Cat: 731214 Rel: 15 Oct 19
 
4-channel sequencer - 36HP
Notes: USTA is a 4×4 tracks sequencer for voltages and gates with variable stage duration, designed to quickly see and edit multiple voltage relationships in real time.

Variable stage duration means that every single stage duration can be individually set in relation to the clock, instead of being constrained to a one-to-one ratio (i.e. one stage per every clock impulse).

4×4 tracks means that every stage can store and generate up to four separate voltages (two CVs and two gates), and that up to four independent stage sequences can be arranged into as many different tracks.

Its architecture is based on an array of 16 'Stages' which form a 'Pattern'; 16 patterns form a 'Track', and four tracks form a 'Project'. Within each track, each stage can provide two gates and two CVs, and a wide set of options is available to define and modify the value of each output ('Layers') and the way it is played ('Colours').

Every Stage is related to a dedicated stepped encoder for quick and intuitive editing, and all the 16 encoders are arranged in an oval layout with a circular playhead. Every encoder is surrounded by a ring of 16 LEDs and a RGB led, to provide a visual feedback of the current setting of that step basing on the layer you are working on (like raw CV, quantized CV, length, gate...) and the way it should play depending on the RGB colour.
Read more
 1 in stock $711.79
Cat: 734891 Rel: 15 Oct 19
 
Portable 2HP power module for compact skiff cases with dual passive mults
Notes: The power module from Endorphin.es is a module for the power supply of smaller modular systems such as skiff cases up to 104 TE width. The module consumes DC power between 12 and 20 volts from an external power supply unit. Voltages of up to +1000 mA and -700 mA are output, also depending on how strong the connected power supply is. In addition, there are two passive multiples.
Read more
 2 in stock $117.90
Cat: 734884 Rel: 15 Oct 19
 
6HP VCO with auto-tuning & octave shift
Notes: The Endorphin.es Godspeed is sort of the single oscillator version of the famous Furthrrr Generator. From its big brother it takes over the digital Thru-Zero core and the legendary wavefolder. But it also has new features like a sub-oscillator output and an immensely practical autotune function.

Especially for people starting with a modular system this oscillator is highly recommended. On 6HP it delivers all the features (and more) needed for diving into the depths of West-Coast-Synthesis!
Read more
 1 in stock $254.20
Cat: 734886 Rel: 15 Oct 19
 
Stereo filter with voltage controlled resonance - 6HP
Notes: Versatile stereo digital filter based on Endorphin's Grand Terminal module. CV-controlled cutoff, resonance and separate high-pass filter. Simple but effective.

Supplier notes:
The Squawk Dirty To Me is a stereo filter with voltage controlled resonance. It features eight filter modes and zero-delay feedback.

- Simple and effective 6hp stereo VCF
- 8 filter modes available with meta CV scanning, famous zero-delay feedback Grand Terminal filters
- Additional hi-pass filter in series quickly cuts the boomy low end
Read more
 4 in stock $180.64
Cat: 749524 Rel: 16 Oct 19
 
Compact modular system with full analogue design - Eurorack version
Notes: Pico System III brings modular synthesis back to the basics - the system has multi functional (instead of single-function, like Pico Drums or Pico Trigger in the Pico System II) analogue modules and is intended to encourage creativity in modular patching.

The system has 31 inputs and 20 outputs (master output is duplicated) + 7 switches; if you have enough patch cables at your disposal, you can patch the system in 121000931215044250740178662400 or 1.21x1029 variations (we ignored the possibility to adjust potentiometers here). Even though only 0,0001% of all patches will sound more-less enjoyable, you and all your future generations can spend a lifetime only patching the Pico System III.

Voice-cards with preset patches set it apart from other eurorack systems - they allow user to change patches instantly and radically, which makes the system well suited for experimental live performances. The system comes with 5 great sounding "factory preset" voicecards, and 5 DIY voicecards that are empty and users can develop their own patches. More voicecards will be available from the Erica Synths shop.

Eurorack module includes: 1 Hosa stackable cable, ribbon power cable, 5 factory preset & 5 DIY voice-cards, user manual and patch note sheets.
Read more
 5 in stock $486.78
Cat: 752820 Rel: 17 Oct 19
 
Comb oscillator, VOSIM, summation synthesis & phase modulation with adjustible waveform & wave folder
Notes: Loquelic Iteritas is a digital VCO with interpretations of three classic synthesis algorithms involving dual pitch control. It creates a huge variety of sounds parameterized by four tone and two pitch controls.

It has had glowing reviews from Surgeon and Surachai, and I am personally very excited about this module!

It has a simple interface, with 3 different synthesis algorithms allied to a number of different controls / CV inputs which have different effects, depending on which mode you choose. Simply hook up a number of modulation sources to the 4 inputs and start wiggling!

Rev.2 now features an additional sync input.

Size: 10HP Eurorack
Depth: 1.5 Inches
Power: 2x8 Eurorack
Draw +12V: 150 / 80
Draw -12: 5 / 5
Draw +5v: 0 / 90
Read more
 1 in stock $354.80
Cat: 732843 Rel: 08 Oct 19
 
Vactrol based low pass gate - 3HP
Notes: Erica Pico LPG is our take on classical Don Buchla LPG designs. We use vactrols in the circuit for that signature sound, and we added some more features, like configurable resonance and built-in decay envelope.
Read more
 1 in stock $118.98
Cat: 744602 Rel: 02 Oct 19
 
Dual signal/audio crossmixer
Notes: The "CROSSMIX" module contains two independent crossfaders with two inputs to one output and is designed for audio or CV sources in the voltage range +-5v (Audio Modular Level).

In addition, the 4 inputs can be switched separately to +6db audio (for external line level sources) using the slide switch on the rear panel.

The two crossmix controls can be recorded. The recording time per channel is more than one minute. The playback speed can be adjusted in playback.

The recorded track is played back once when the Play button is pressed briefly (one shot) or in the loop when the button is pressed a little longer.

Both crossfaders have a separate reset input as well as a separate CV input (+-5V ) for controlling the mix e.g. by an LFO.

The track data remains permanently stored (battery buffered memory).
Read more
 1 in stock $194.72
Cat: 731184 Rel: 02 Oct 19
 
5U version of the Ataraxic Iteritas
Notes: Ataraxic Iteritas Magnus is an extension of the first Eurorack module, the Ataraxic Translatron. AIM starts with one of three bit tables shaped via variable interpolation that is then scrolled through, amplitude modulated, folded, and distorted by the CV-controllable front panel controls. Subby basses, metallic drones, unrelentingly digital timbres and more are all to be had from the AIM. Ataraxic Iteritas Magnus is the 5U version of the Ataraxic Iteritas. Guaranteed to make the fax machine jealous on an even bigger scale.
Read more
 1 in stock $448.93
2hp
Cat: 727385 Rel: 02 Oct 19
 
High fidelity audio processor focused on granular synthesis
Notes: 2hp Grain is a high-fidelity audio processor focused on granular synthesis. It's capable of generating granular clouds, microsound phrases, and unique textures that are derived from any input signal. The Density control sets the rate of granularization applied to the input signal and sets its position within the buffer. The Mix control sets the balance between live input and the granular audio stream for dialling in the perfect combination of sounds. In addition, there is a frequency control and associated v/oct input allowing for pitch accurate sequencing of grains. Particle patching has never been smaller with Grain.
Read more
 1 in stock $157.92
Cat: 739889 Rel: 02 Oct 19
 
Four-channel precision adder, buffered mult, and transposition tool
Notes: Quantus Pax is a four-channel precision adder, buffered multiple, and polyphonic transposition utility. Each channel has two CV inputs and can be further modified by the three Xpose inputs. QP is made with high quality low-tolerance resistors for unbeatable accuracy. Patch-wide key changes, polyphonic movement, mathematically derived melodies, and more are all to be had with this simple but useful utility.
Read more
 3 in stock $256.37
2hp
Cat: 727389 Rel: 02 Oct 19
 
Digital oscillator module with sub output & wavefolding - black
Notes: Sine is a harmonically pure VCO with two distinct outputs.

The primary output contains a perfect sine wave with a wide frequency range and pristine volt per octave tracking. The Sub output features two sine tones that can be blended together to achieve a mix of one octave below, or a fifth above the primary output's frequency.

In addition, both outputs have an internal wavefolder that adds harmonic content to the signal allowing for spectrally complex tones within a single module. Keep your tones pure (or not!) with Sine.
Read more
 2 in stock $149.27
Cat: 740273 Rel: 02 Oct 19
 
32 step sequencer with fractal-like pattern generation
Notes: If we're honest we don't really understand fractals. Something to do with maths, apparently. But that doesn't really matter because we do understand this sequencer module, which is ideal for randomly twisting and morphing sequences.

Supplier notes:
Bloom is a fractal sequencer capable of generating infinitely evolving melodies with a host of musical features.

At its core is a powerful 32 step sequencer with two independent channels and an intuitive interface. What makes the Bloom come alive are its fractal algorithms which can transform existing sequences into powerful melodies, or even generate new patterns altogether. The base sequence is known as the Trunk and can be programmed by hand, or automatically generated with the Mutate function. Once a Trunk sequence is in place, fractal transformations are only a knob turn away by using the Branch and path controls. Each new Branch adds a complete variation to the base sequence and Path determines its passage through the set of recursively generated sub-sequences, offering a unique take on the melody with each turn of the knob.

Bring your sequencing to life with Bloom.
Read more
MRP:$414.09 SAVE 17%
 5 in stock $345.08
FORTHCOMING
Befaco i4 Instrument Interface Preamp Module (assembled)
MRP:$284.28 SAVE 17%
coming soon $236.90
FORTHCOMING
Koma Elektronik Sensor Interface Eurorack Module
coming soon TBA
FORTHCOMING
Befaco Inamp Module (assembled) Befaco Inamp Module (assembled)
Cat: 749089
 
Dual pre-amplifier module - 4HP
Notes: Inamp is a dual pre-amp in just 4 HPs. Featuring 6,3 Jacks inputs as well as Minijacks.

Both inputs are summed so you can use them at the same time as an input mixer.

The unit is designed to amplify up to x20 the input signal, allowing to amplify most of the music machines out there (Domestic line levels) as well as some guitars (Humbucker-like pickups and so).

The first channel is normalled to second one in series, so it's possible to have two stages of amplification or two separate ones.
Read more
MRP:$175.24 SAVE 17%
coming soon $146.04
FORTHCOMING
Befaco VCMC Voltage Controlled MIDI Controller Module (assembled)
MRP:$414.09 SAVE 17%
coming soon $345.08
FORTHCOMING
Befaco Percall Module
Cat: 739916
coming soon TBA
Cat: 732852 Rel: 27 Sep 19
 
Ring modulator with internal oscillator
Notes: Erica Pico Ring is a balanced modulator (quadrant multiplier) circuit to create bell-like, metallic or robotic sounds. It has built-in sine-wave modulation oscillator for more versatility.
Read more
 1 in stock $98.43
Cat: 743610 Rel: 23 Sep 19
 
Complex quad multimode filter - 20HP
Notes: Mad dual-channel filter with two peaks per channel. Chain the sides together for complex filter curves, process stereo sounds or even turn up the resonance for four self-resonating peaks.

Supplier notes:
The Stereo Dipole is a Quad Multi-Mode VCF featuring single, dual and quad peak filter outputs.

Designed to be clean or characterful, the Stereo Dipole is not intended on achieving any one type of sound. From clean frequency-based panning to complex phasing and formant synthesis and over-driven squelchy bass lines, Stereo Dipole offers an environment which is simple enough to use, while providing the versatility to push your sounds into unknown territory...

Comprised of two identical filter sections that can be used independently via the dedicated Resonance (RES), Primary Cutoff (FREQ) and Secondary Cutoff (SPREAD) controls as well as in tandem via the STEREO FREQ and STEREO RES controls in the centre of the module.

Both the Left and Right Channels feature Single Peak POLE and Dual Peak DIPOLE outputs.

High Pass, Low Pass and Band Pass outputs are individually selected via the switches, situated above POLE and DIPOLE.

The Dual Peak DIPOLE output can be routed either in Series or Parallel with the main POLE VCF while maintaining all possible configurations of the Selected Filter Types.

Series and Parallel combinations will provide capabilities such as 24dB/OCT HP/BP/LP, Variable Width Band Pass and Notch as well as other obscure filter combinations.

FREQ controls the Cutoff of both the Primary and Secondary VCF while SPREAD is used to Match (centre position) or Offset the Secondary Cutoff Frequency by +/-5 octaves..

DIPOLE AB is a Quad Peak Monophonic Output, sharing the same Routing and Topology combinations of the four VCF cores.

The A input (LEFT) provides Normalization into the B input (RIGHT), allowing for a stereo image to be created from any monophonic signal source. All four A/B outputs can be utilized in stereo for more complex stereo filtering applications.

Pre-Filter Input DRIVE Control on each channel will push the input signal into heavy soft-clipping and saturation; adding Harmonic Content and increased low end for the VCFs to bite into. A Sine Wave can be over-driven enough to be useful with pleasing results.

RESONANCE may be nuanced or pushed all the way into Self-Oscillation across the entire bandwidth of 20+ Octaves.

All VCF cores Track 1V/OCT and Temperature Compensated.

The Stereo Dipole can fully function as a Single, Dual and Quad Sine Wave VCO/LFO.

The Series Routing configuration allows for additional tonal oscillation capabilities via the DIPOLE and DIPOLE AB outputs.

In addition to the A, B and Stereo 1V/OCT Inputs, the SPREAD CV Inputs may also be used as direct and accurate 1V/OCT control of the Secondary Peak on each channel.

Individual and Stereo Control Voltage inputs including Attenuators for STEREO RES, RES A/B and STEREO FREQ as well as Polarizing Attenuators for each Channel's FM CV input.
Read more
 4 in stock $399.17
Items 1 to 50 of 788 on page 1 of 16
1  2  3  ...  16  »

Filter

Saved Searches
Save current search
Release Date
Close