Search dance music

Notes: Sono Abitus is a high-quality output module. It has a stereo pair of Eurorack-level 1/8" inputs that feed a pair of 14" TRS jacks for line output and a 14" headphone output. The headphone output and line outputs have separate level controls, making it easy to monitor while performing or recording.

Size and power:
4 HP

+12v: 50mA

-12v: 50mA

+5v: 0mA

Sono -- from Latin: "to make a noise"

Abitus -- from latin: "way out, exit"

"Make noises exit"

Notes: A warm and deep sound source you can rely on

A flexible and warm Analog Multifunction Oscillator, rich in harmonics. Excellent for performance use!

ONA can work as an Audio Oscillator or as a Low Frequency Modulator and it provides control over all its parameters, making it a versatile, deep and easy-to-use oscillator.

Thanks to its triangle-core oscillator and wave-shapers you can choose between a big palette of output waveforms to give shape to your ideas.

Classic Waveforms. Sine, Triangle, Saw and Square.

2 Complex Waveforms with Pulse Width Modulation.

2 Sub-Waveforms to add some bass sounds easily.

Blend them to give unlimited depth to your sound!

Notes: 10HP Edges Clone with integrated midi interface and PSImidi which allows any TRS midi cable to be used.

MIDI Functionality:

MIDI Learn: Press this button and send a midi note. The device will use that channel as the base channel

MIDI Mode: This button cycles between two operational modes.

1. 4 single voices trigger on 4 midi channels starting on the base MIDI channel (i.e. base channel is channel 2 so the voices are mapped over channels 2, 3, 4, 5)

2. Simple Poly mode where each voice plays on a different note on the same midi channel

Note about MIDI and Gating: The gate is normalled OPEN by the Gate 1 input. This is by design but will also force the gate open when the device is triggered by midi. Placing a dummy jack will break the open normal the gate will trigger via MIDI normally

Notes: 8HP Tides version 2

Fully calibrated.

Notes: 8HP Tides version 2

Fully calibrated.

With LED Pots for the attenuverters.

Notes: F8R is a 8 channel, 16hp control surface for Eurorack

16HP Width, 20mm Depth
Current Draw: +12V 50 mA, -12V 40 mA

Basic Usage instructions:

Front:

Voltage Select switches: Independent for each channel. Does NOT affect MIDI/I2C data

Slider LED color: To change the LED color, simply remove the cap and rotate the square LED 180s. Do NOT force the LED back in, it should slide in easily, may require wiggling.

Rear:

Power Header: Standard 10pin power cable, there is NO polarity for this connection. It can be connected either way

MIDI Out Header: This is a 4 pin header but only 3 or 2 connections need to be used. To connect to a DIN cable, either GND, 5 (to pin 5, current sink/aka -), and 4 (to pin 4, current source/aka +) should be used. For internal module to module connections, only pin 4 and 5 should be used. The ground pin is only for the shield in a midi cable, it is never connected on a midi input and isnt necessary for the short module to module lengths

I2C Header: 3 pin header to connect to other I2C devices in your rack, this is an unbuffered connection so cable lengths should be as short as possible (20cm/6" recommended). There are 4.7k pull up resistors on this connection

Module Orientation jumpers: There are 3 of these jumpers which determine how the module operates depending on if the jacks are on top or bottom. They will come installed in the position matching your panel but can be changed should you want to flip it. "INV" is Jacks on Top, the white position is jacks on bottom. Changing these jumpers will change the numbering of the faders from left to right (1->8) in both MIDI and I2C and will invert the voltage response (i.e. 10->0V from top to bottom). The jumper is shown in the "jacks on top" position in the pic below. ALL THREE JUMPERS MUST BE IN THE SAME POSITION for the module to operate correctly.

Module Config DIP switch: This allows you to switch between I2C Follower and I2C Leader modes easily. Simply move the switch to the "lead" position and restart the module (you can press the blue reset button once). The other 3 positions are for future expansion and not currently implemented.

Connector for Expander: This connects the F8R to the I/O expander. The cable is attached to the expander. Note the keyway at the top of the part, the connecter will ONLY connect one way

Notes: This is 2 x opensource branches. The input of channel one is normalled to all other inputs so you can run this as 1 to 4, 2x 1 to 2, etc. Dual Color LEDs on sliders

Notes: 6HP Micromodule of MI Warps.

Notes: Delta-V is a fully analogue dual-channel function generator, featuring a dedicated VCA and LFO cycle switch for each channel. It packs a great deal of functionality in only 10HP, and will surely find use in almost every patch.

Generate envelopes, slew gates and signals, or run LFOs with precise control over attack and decay times. Using the SHAPE knob, Delta-v can create a wide range of envelopes, from very snappy exponential curves for percussion to logarithmic thumps for bass lines.

If VCA's input is unpatched, the module outputs a regular voltage envelope. When an audio signal is patched into the VCA input, the output signal becomes the audio signal amplified by the envelope.

Sending other envelopes or an LFO to VCA input lets you modulate those modulators, quickly creating complex control voltages that go beyond the usual attack-decay envelope.

Combine this with the SUM output, which sums the two channels, and the attenuverters, which can quickly attenuate or invert the signal, and you have a whole array of signal processing capabilities.

The TRIGGER input fires a Attack-Decay envelope, while the SLEW input will affect the rate of change of the signal.

The trigger for channel 1 and 2 can be linked together, so you can fire two envelopes with one patch cable.

Each channel has an End of Cycle output, (EOC) this outputs a short trigger at the end of each envelope cycle.

The output voltage ranges from -10 to +10 volts, set with handy output attenuverters.

The CYCLE switch starts looping the envelope, creating LFO's that go up to audio rate, and that can also be used as an interesting sound source.

There are many ways to utilise Delta-V.

Challenge yourself to explore new, unconventional territories!


Width: 10HP
Depth: 27MM
Power: +12V 70 MA
Power: -12V 70 MA
Power 5V: 0 MA

Notes: Pique (uPeaks)

Pique is a micro version (4HP) of the popular Peaks module from Mutable Instruments. It can be an ADSR-style envelope generator, an LFO and a drum emulator.

The module is calibrated, comes with a power cable, and a one year warranty.

Notes: Pique (uPeaks) 1U Intellijel Format

This is a 1U (Intellijel format) version of the Pique module which is based on the popular Peaks module from Mutable Instruments. It can be an ADSR-style envelope generator, an LFO and a drum emulator.

The module is calibrated, comes with a power cable, and a one year warranty.

Notes: Erica Synths Black LPG is our take on Lowpass Gate idea - it's designed from scratch
module featuring 2nd order lowpass VCF (the original Buchla lowpass gate was 1st order
VCF) and VCA combo with distinct resonance circuit on top. Voltage control over VCF cuto
frequency/VCA oset and mode (VCF/VCF+VCA/VCA), as well as built in decay envelope
generator makes it a versatile module for sound shaping in any modular setup.

FEATURES:
Three vactors for 2nd order VCF
VCF/VCF+VCA/VCA modes
Manual and voltage controlled cuto/oset
Manually and voltage controlled mode selection
Manually resonance depth control
Resonance overdrive switch
Built in decay envelope generator
Manually and voltage controlled decay time
Envelope CV output
Ski-friendly design

SPECS:
Audio output amplitude 10Vptp
CV range (full span) -5V - +5V
Max Decay time 4''
Panel width 10HP
Module depth 35mm
Power consumption 44mA@+12V, 45mA@-12V

Notes: The ADDAC302 Nchunk Control module allows you to connect a Nintendo Nunchuck controller to your modular synth, featuring a two-axis thumb joystick, a three-axis accelerometer and two trigger buttons.

The module provides CV outputs for all of the Nunchuck's parameters and special functions to remap the CV outputs. The remapping can be both continuous or step-by-step and can be accessed through either the dedicated CV inputs or the manual controls.

A specially dedicated Mix output averages between the first two CV outputs, a very useful feature for continuous control parameters.

Mechanical:
- Format: Eurorack
- Width: 8 HP
- Depth: 4 cm

Control Voltage I/O:
- CV inputs: 0 - 10v
- CV outputs: 0 - 5v
- Gate in threshold: 2.5v

Electrical:
- Compatible with +-12v and +-15v power supplies
. Max current: 100mA?
. Bus Board Cable: 8 × 2 IDC (Doepfer style) connector

Notes: The Looping ADSR is an extremely versatile envelope generator. It can act as a traditional ADSR envelope requiring a gate signal to activate or as a looping ADSR. Envelopes can be output with both linear and exponential curves. In Loop Mode it repeats the cycle of Attack, Decay, & Release. Once the Release phase is complete, it loops back to the Attack and begins the cycle again. The Looped envelope can be further manipulated with the Loop Scale knob. Loop Scale shrinks the overall size of the envelope while keeping the ratio of A:D:R identical. All knobs on the Looping ADSR have CV input. As with all Hungry Robot "Modular Boxes" the Looping ADSR can be powered with a simple 9V DC, Negative Center power supply.

KNOBS
-ATTACK: Sets the attack length (1st stage of ADSR cycle). Determines how long it takes to come to full voltage after gate is applied (up to 10 sec.)
-DECAY: Sets the decay length (2nd stage of ADSR cycle). Determines how long it takes to go from full voltage to sustain voltage (up to 10 sec.)
-SUSTAIN: Sets the sustain level. Determines what voltage the envelope returns to after decay stage
-RELEASE: Sets the release length (Final stage of ADSR cycle). Determine how long it takes to return to 0V after gate is released (up to 10 sec.)
-LOOP SCALE: When in loop mode, this knob scales down the length of the envelope while keeping the ratios identical

SWITCHES
-LIN/EXP: Selects the envelope type: linear vs. exponential curve
-LOOP/ADSR: Switches between Loop and ADSR mode. LOOP turns the loop on. ADSR is a traditional ADSR requiring a gate signal
-RPT./GATE: Works only in LOOP mode. RPT. automatically repeats the loop without a gate. GATE mode requires a gate to begin looping.

PATCH POINTS
-LS.CV: CV input for Loop Scale. Allows for CV control of this parameter.
-A.CV: CV input for Attack. Allows for CV control of this parameter.
-D.CV: CV input for Decay. Allows for CV control of this parameter.
-S.CV: CV input for Sustain. Allows for CV control of this parameter.
-R.CV: CV input for Release. Allows for CV control of this parameter.
-GATE: Gate input for ADSR mode as well as Gate/Loop mode
-OUT: Output of final envelope for all modes.

Dimensions: 4.7" x 3.7" x 1.96"
Power: 9V DC - Negative Center - 2.1mm Barrel

Notes: The A-143 series of modules contain multiple modulation sources. Module A-143-2 is a four-fold ADSR type envelope generator. Other modules of this series are the Complex Envelope Generator A-143-1 (Quad AD) and the Quad LFO A-143-3.

The module contains 4 independent ADSR-type envelope generators. Each sub-module has available the controls Attack, Decay, Sustain and Release. The three-position Range switch allows to select the desired time range (low - high - medium). The adjustable envelope time ranges from several minutes to some milliseconds. On top of this each sub-module is equipped with three digital outputs (high/low): "End of Attack (EOA)", "End of Decay (EOD)" and "End of Release (EOR)". As soon as the criterion is valid (e.g. end of decay state) the corresponding digital outputs turns to "high". These outputs can be used e.g. to daisy-chain several ADSR sub-modules. For this the digital output in question (EOA, EOD or EOR) has to be connected to the Gate input of the following ADSR. Even automatically running envelopes (pseudo LFOs) or so-called "quadrature envelopes" with cyclical modulations of several ring-shaped, daisy-chained ADSRs are possible. To obtain a pseudo LFO simply the EOD or EOR output has to be connected to the Gate input of the same ADSR.

In addition to the obligatory Gate (G) input for envelope generators each sub-module has available a Retrigger (Rt) input. The retrigger turns the direction to "upward" if the envelope has already reached the decay state while the retrigger pulse occurs. If the envelope is still in the attack phase the retrigger input has no meaning. This a different behaviour from A-140 and A-141!

The Gate inputs of the units 2, 3 and 4 are normalled to the Gate input of unit 1, i.e. Gate input 1 is connected to the switching contacts of the Gate input sockets 2, 3 and 4. Thus one Gate signal applied to Gate input 1 can be used to trigger all four sub-modules simultaneously.

The envelope outputs are displayed with LEDs.

The maximal envelope voltage (Attack/Decay reversal point) is about +8V.

If voltage control of all parameters is required module A-141 is available.

Notes: VCO:

- Tune: manual tune control (with an internal jumper the range can be set to ~ +/-1 half an octave or ~ +/-2.5 octaves)
- Oct: range switch -1 / 0 / +1 octave
- Mod: modulation depth (attenuator wired to the Mod. socket)
- Dest: switch that is used to address the modulation to frequency modulation (position FM) or pulsewidth modulation (positon PM), in centre positon no modulation
- PW: manual pulsewidth control for rectangle waveform, PW can be also modulated by the Mod. input as mentioned above
- Wave: waveform switch (sawtooth / off / triangle), the sum of the waveform chosen by this switch and the rectangle is fed into the VCF (to turn the rectangle off the PW control has to be set fully CCW or fully CW)
- 1V/Oct. (socket): external CV input for VCO frequency (1V/octave)
- Access to internal bus CV (via jumper, optional, please remove the bus jumper if this feature is not used to avoid unwanted frequency modulation as then the unused CV line of the bus works as a kind of antenna)
- Triangle core VCO, frequency range about 32Hz ... 8kHz

Balance unit:

- The balance unit is made of two VCAs which are controlled by the sum of manual Balance control and the balance CV input in the opposite direction.
- The audio input of VCA1 is hard-wired to the VCO output, audio input 2 is connected to the socket Ext.In.
- The output of the balance unit is used as audio input for the VCF
- Bal.: manual balance control, fully CCW the internal VCO is used, fully CW the external signal (Ext.In) is used, at centre position both signals have about the same level
- CV Bal.: CV input for balance (range about 0...+5V)
- Ext. In: external audio input for VCA2, about 5 Vpp level required for similar loudness as the internal VCO
- This socket is normalled to the internal VCO suboctave f/2 signal (rectangle with half the frequency), if no external signal is applied the suboctave signal is used as the second signal for the balance unit

VCF:

- 24 dB low pass
- Frq: manual frequency control
- FM1: frequency modulation depth (attenuator wired to the VCF FM1 socket, the socket is normalled to the internal Envelope signal and then FM1 controls the modulation depth of the internal envelope applied to the filter)
- FM2 (socket) : second CV input for VCF without attenuator (about 1V/octave), can be used e.g. for VCF tracking by connecting the same CV which is used also for the VCO frequency
- Res: manual resonance control (up to self oscillation)
- If the VCO is turned off (waveform switch = centre position, pulsewidth control = fully CCW or CW) and the VCF resonance is set to maximum the module can be used as a sine oscillator, the tracking at socket VCF FM2 is about 1V/octave (not as precise as the VCO but much better than most other filters)
- ~ 11 octaves frequency range (~ 10 Hz ... 20kHz)

VCA:

- Gain: manual amplitude control (initial gain), can be used to open the VCA without envelope signal
- VCA (switch): used to switch between gate and envelope as control signal for the VCA, in centre position the VCA is not controlled by envelope or gate
- Note: when gate is used the VCA is controlled directly by the gate signal (i.e. hard on/off), this may lead to clicking noise under certain conditions (especially with low VCO/VCF frequencies)
- Special control scale: exponential scale in the range from about -20dB to -80/90dB, linear scale from about -20dB to 0dB
- Remark: this special control scale results in a loudness behaviour that is a bit different from pure linear or exponential VCAs
- Out: audio output of the module (= VCA output)

Envelope:

- Gate (socket): Gate input (min. +5V), can be normalled to the bus gate signal by means of a jumper
- Att: manual control for Attack
- D/R: manual control for Decay/Release
- Env. (switch): used to switch between A/D, ADSR and A/R mode of the envelope generator, in centre position (ADSR) the sustain level is fixed to about 50%
- Envelope (socket): envelope output (about +10V)
- CVT (socket): CV input for time control, by means of two internal jumpers one can select which time parameters are controlled by the CVT input (e.g. A only or D/R only or A/D/R) and in which direction (i.e. if an increasing CVT shortens or stretches the time parameter in question)
- Envelope LED display
- Attack time range: ~ 1ms ... 5 sec (can be extended by using the CVT input)
- Decay/Release time range: ~ 1ms ... 15 sec (can be extended by using the CVT input)

Notes: The module can record the joystick movement up to a length of over a minute. The sequence remains stored in the battery-backed RAM after switching off. When playing the sequence, it can be manipulated in speed and playback direction.

There is a FREEZE function to hold the current joystick position plus an external reset input. In addition, a GATE is set during movement and a CV voltage is output as a function of the joystick movement. The ranges of the X / Y output voltages are bipolar +/- 5v or unipolar from 0 to + 10v. Both channels X and Y have a passive attenuator potentiometer, so that the voltage range can also be set lower.

Notes: Versatile stereo digital filter based on Endorphin's Grand Terminal module. CV-controlled cutoff, resonance and separate high-pass filter. Simple but effective.

Supplier notes:
The Squawk Dirty To Me is a stereo filter with voltage controlled resonance. It features eight filter modes and zero-delay feedback.

- Simple and effective 6hp stereo VCF
- 8 filter modes available with meta CV scanning, famous zero-delay feedback Grand Terminal filters
- Additional hi-pass filter in series quickly cuts the boomy low end

Notes: Viol Ruina is an all-analogue distortion and lowpass filter with an internal envelope follower and self-modulating cutoff. The four-pole design is reminiscent of the classic filters we all know but with a completely new and slightly ridiculous twist. The independently addressable distortion circuit takes VR into overdriven paradise with a shocking amount of drive. Built-in envelope following makes an easy way to create dynamic patches with the flick of a switch, and feedback FM takes VR to a whole new realm of filthiness. Run a sound through VR, you'll get something cool out of it.

Notes: Row Power is a clean, regulated, and protected power solution for eurorack systems. Row Power 35 provides 35W of power, suited for any typical eurorack row (84HP to 168HP):

+12V @ 1.4A
-12V @ 1.25A
+5V @ 1.0A

Simply plug a universal power supply (laptop style) into either of the barrel plugs on the 4HP panel. Connect your modules via flying-bus cables or the Bus Stick.

Daisy-chain multiple Row Powers to use a single power brick for multiple rows (typically 3-5 rows per power brick). Each row will be independently regulated and protected for ultra-low cross-talk between rows. Rows can also be hot-swapped (plugged/unplugged without powering the whole system down).

Notes: Ultra-simple 16-step Eurorack CV sequencer with randomisation option and storage for up to 16 patterns. Straight to the point business, all in just 4HP of rack space.

Supplier notes:
Small, easy-to-program sequencers are a bit of a rarity. Vox Digitalis is our answer to this issue. With intuitive displays and simple controls, VD is perfect for all your pitch CV needs. Set your sequence length, dial in each note, randomize, save and load 16 sequences -- VD does all the stuff the big sequencers do, just in 4HP.

Notes: The original MiniMod Glide +Noise module was based exactly on the original Minimoog Model D circuitry, which was designed to be used with the built in Model D keyboard, and because of its vintage design its range was severely limited to 5 or 6 octaves, and it also responded to positive voltages only. Another limitation was that it would not return fully to zero when selecting long glide times, which restricted the range even more.

So we made the decision to re-design the MiniMod Glide + Noise using modern precision parts, and we have come up with an all new circuit which has exactly the same function, but with a hugely extended range. It has the same Glide slope characteristic (a slightly curved Linear Glide) as the Model D on which the MiniMod is based, however in response to many requests from customers we have adjusted the glide up and down speeds so that they are now very similar , which is much more useful in real world applications that the earlier MK1 version which (like the Model D) would glide up considerably faster than it would glide down.

The new Mk2 MiniMod Glide Noise module now has an impressive 14 octave range, and can respond to negative voltages down to -5V. This is a very useful feature, as our MiniMod VCO's will respond to negative control voltages and produce correspondingly low frequencies; so it is now possible to glide down quickly or slowly to crazy sub bass levels! The hold feature has been improved too, it covers the full audio range as well as DC control voltages, and works as a track and hold module with Eurorack signal levels.

A further enhancement is that the Mk2 module can now (using selectable jumpers) transmit or receive pitch CV to the Eurorack power bus; for example, the Glide CV Output can now be directed to the Bus in order to send CV's to (for example) three VCO's via the bus without the need for a passive multi and four patch cords!

The Noise section of the module is unchanged, except that we have slightly boosted the level of the Red Noise output to bring it more in line with Eurorack control voltage levels.

Lastly, it is much shallower - Mk1 Glide Noise had a depth of 54mm, and it was the only MiniMod module that was too deep to fit a skiff style case - and this prevented a full MiniMod system being installed into a shallow Eurorack case. The new MK2 version is only 28mm deep, so this allows both it and a full MiniMod system to be mounted into shallow skiff style Eurorack cases.

Dimensions: 6HP wide, 26mm Deep
Current draw: 36mA Positive, 38mA Negative

Notes: Erica Synths Snare Drum is developed in collaboration with the French company e-licktronick and it's our take on analogue snare drum circuits adapted for modular systems. Sharp, punchy sounds, Accent & CV control over key parameters of the module make it distinctively expressive in studio and live performances.

Features
Tune, Snappy, Noise tone and Decay controls
CV control with attenuators over Tune and Decay
Manual trigger
Accent for better expression

Specifications
Decay range: 150ms - 260ms
Audio output level: -5...+5V
CV level (full span): -5 - +5V
Accent CV level: 10V
Trigger level: 5V
Trigger time: 1ms
Power consumption: 37mA@+12V, 35mA@-12V
Module width: 10HP
Module depth: 35mm

On this run of modules the Pitch & Decay CV inputs are inverted: rising CV will decrease pitch, falling - increase.

Notes: Erica Synths Drum Mixer Lite is compact version of Drum Mixer. It features extended headroom and a dedicated drum compressor of unique design keeps each drum sound clearly distinguishable and add power to the final mix. Bonus feature - effects send output allows to apply external effects to the signals on the first three inputs. LEDs next to each input give visual feedback on the signal level.

Features:
6 inputs
Built in vactrol based drum compressor with Amount and Decay control
Three inputs assignable to main or aux send outputs
Main and Aux Send outputs
Signal level indicator LEDs

Mixer gain: -+6dB
Power consumption: 59mA@+12V, 36mA@-12V
Module width: 10HP
Module depth: 35 mm

Notes: Sewastopol is a multifunction Eurorack module designed for easy interfacing of external gear to your modular environment. It can export line and professional level audio, import audio from instruments and electroacoustic transducers, and analyse the incoming audio to generate voltages and triggers to control your modular system.

This is a second, vastly improved revision to the original 2014 Sewastopol, featuring a completely redesigned preamplifier circuit, better ergonomics and various other improvements.

Notes: Clep Diaz is a handy and small step CV and LFO generator. In step and random modes, use the encoder to control the number of steps in the sequence; in LFO mode, the encoder controls the amplitude of the wave. Toggle the directionality of the sequence: up, down, or up/down to customize the CVs further. CD also gives CV control over the number of steps in the sequence and an end-of-cycle trigger output. Unipolar and bipolar outputs allow maximal control.

Notes: The Shifty is essentially a combination of four sample and hold stages, a sequential gate and sequencer controller. This collection of functions allows for some specific and useful utility application.

One of the primary uses for Shifty is to take a monophonic sequence source and route each new note of the sequence to up to four different synthesizer voices in a specific pattern. In this way you can create pseudo polyphonic sequences since each voice can be triggered to play and sustain while the next voice int the sequence gets triggered. Another term for this is hocketing.

The other main application of the Shifty is to function as an Analog Shift Register. In this mode each new gate input received causes the current set of pitches to be shifted to new output locations as a new one is added and the oldest one is replaced. This can be an interesting way to create chords that are up to four stacked notes when used with a pitch sequence source that has a harmonious series of notes (e.g. a pentatonic scale works really well). Even just using two of the outputs will yield very interesting melodic interplay and is an excellent way to make a simple sequence much more complex and interesting.

In a more basic way the Shifty could be used as a simple Sample/Track and Hold module or as a sequential gate.

Notes: The Listen Four Quarters is a four channel stereo mixer with 1/4" (6.35mm) TRS balanced outputs and 1/8" (3.5mm) headphones output. Two mono channels with Pan knobs and two stereo channels with dual inputs provide optimal compatibility with both stereo and mono signals. The Listen Four Quarters can be daisy-chained to other Listen modules to create a larger mixer with sub-mix outputs.

Notes: Module A-112 is the combination of a voltage controlled 8 Bit Sampler and a wavetable oscillator. On top of it the module is able to generate some special effects. A-112 was designed as an additional sound source with the typical sounds of the early 8 bit samplers and is not comparable with the modern polyphonic MIDI samplers available on the market.

Sampling mode: 8 bit audio resolution, 128kB memory in 2 banks 64kB each (equivalent to 2 seconds of sampling time for each bank with 32 kHz sampling rate), audio input with attenuator, overload display in record mode (gate LED), possibility of MIDI Dump to store sounds in a computer via MIDI, non-volatile memory for the 2 samples in the module, manual tune control for adjustment of sampling rate for record and play, CV input (~ 1V/Oct), both manual tune and CV determine the sampling rate respectively the pitch (pitch range is 5 octaves), gate input (not a trigger: the sample starts at the positive edge of the gate signal and is played as long as gate is high or until the end of the sample is reached), manual Gate button, non-filtered audio output (thus quantizing noise can be used as an element of the sound intentionally).

Wavetable mode: special appearance of the sampling mode when playing a sample, the audio input is now used as a second control voltage input for moving through the sample in 256 byte wide loops (wavetables). The control voltage required to move through all wavetables applied to the input "Wave CV In" is in the range -2.5V (wavetable 1) ... 0V (wavetable 127) ... +2.5V (wavetable 256) when control "Atten." is set fully clockwise. To achieve the typical wavetable oscillator sounds the sampling memory must contain corresponding wavetable data (e.g. loaded via MIDI dump). These data contain a set of wavetables with different harmonic content (e.g. a filter sweep) to get the typical wavetable sound while moving through the tables via CV. But you may also use a "normal" sample and go through the sample with CV to obtain partially amazing sounds never heard before. You may use for example sampled speech and go with CV through the syllables or speech shreds to get really very extreme sounds. An ideal addition for this feature is the Offset/Attenuator module A-183-2 which can be used to adjust the position of the wavetable (Offset) and the modulation depth (Att.). The corresponding jumper of the A-183-2 has to be set to bipolar offset (as the A-112 requires -2.5V...+2.5V to pass through all 256 wavetables). As modulation source an LFO (A-145, A-146, A-147, A-143-3), ADSR (A-140, A-141, A-142, A-143-1/2) or a random voltage (A-118, A-149-1) may be used. Even a ribbon controller (A-198 or R2M), the Theremin module A-178, the Joystick A-174 or the Wheels module A-174-2 are useful to drive through the wavetables.

Effects: Additionally, the module offers - in a way free of charge - some effects like delay, reverse delay, pitch shifting or freeze. But it has to be pointed out that due to the 8 bit audio resolution these effects are not comparable to high quality effect units and should be understand as an extra for nothing. The A-112 is not an effects unit!

The sampling time of the A-112 is about 1...30 seconds corresponding to a sampling frequency range of about 60kHz...2kHz (64kB@60kHz ~ 1 s, 64kB@2kHz ~ 30 s).

Technical note: the module uses a battery for the non-volatile storage of the sampling data. Batteries have a limited lifespan and have to be inspected at least every two years. For details please refer to the FAQ page of our website: Lifespan of rechargeable batteries (used for memory backup).

Notes: The FUNCTION music synthesizer module is part of the MATHS family of control voltage utility modules. It is a small analog computer designed for solely musical purposes.

Features:

Generate a variety of linear, logarithmic, or exponential functions
Functions as short as 2ms and as long as 25 minutes per cycle!
Triggered Functions (Envelope)
Continuous Functions (LFO)
Invert and/ or Integrate (Lag, Slew, Portamento)
Discrete Time Functions (S&H, T&H)
LEDs indicate activity on all outputs
End of Rise and End of Cycle Pulses facilitate programming of more complex functions
All outputs capable of driving a passive 4 way mult without loading effects (no buffered mult needed here)
Perfect for modulating the DPO and just about anything else

Specifications:

Width: 8hp
Max Depth
(incl. power cable): 32mm
Power:
30mA@ +12V
20mA @ -12V

Notes: 221.x2 is a clean and precise utility module that is equally at home mixing Control Voltage as it is audio. At its simplest, it is two independent 2-to-1 mixers that offer per-channel attenuation and inversion, as well as +6dB of gain available at the summed outputs. With a tap of the "All Mix" button, these separate mixes can be combined into a 4-to-1 mix at the "All Mix" output - meanwhile, the first 1+2 mix is still available at its respective summed output. A rear expansion input and output allows for combining multiple modules into larger systems.

In addition, each channel also offers a Direct Output that can be taken pre or post attenuation/inversion.

A 6-volt offset is normalled into the input jacks of channels 2 and 4. This voltage is available at the channel's Direct Output, as well as added to the mixed outputs. Useful as an offset for mixing with another CV signal, or simply as a voltage source.

Each summed output group has two blue LEDs for displaying the shape of the summed CV, and can also serve as signal present indicators for audio. Peak LEDs trigger at ~9.6V, allowing for a bit of headroom before things get out of hand.

Specifications:

Width: 10HP
Depth: 3.3 cm
Power: 133 mA @ 12V
129 mA @ -12V
Inputs/Outputs: All I/O is unbalanced
Input Impedance: 10 Mohms
Output Impedance: Mix Outputs: 330 ohms
Direct Outputs: 10 ohms

Notes: Superior 60 mm quad fader CV source including MUTE feature

The ACL Fader CV Source Module comprises 4 individual faders where each can generate a CV either going between 0 and +5V or 0 and +10V unipolar or -5V and +5V or -10V and +10V bipolar, selectable using 2 jumpers on the backside of the module.

Furthermore there are mute-switches for each channel accompanied with an dual color LED (green/red) which shows the channels mute status. When mute is activated or deactivated, short fade ramps will be generated as well as the fader itself is slightly slew-limited internally in order to generate a smooth CV.

This module is very useful to control VCA's or VC mixers like our VC Amp mix module.

Notes: The SC (Stereo Channel) is a single-channel stereo module for the CGM Eurorack mixer, fully compatible with every other product of this family.

It features a mono/stereo local output which makes it ideal for multitrack recording and advanced parallel processing.

Thanks to its advanced I/O configuration, it can work as stereo-to-stereo, mono-to-mono, mono-to-stereo, and stereo-to-mono.

The gain control and the two mono FX sends can work in pre or post-fader mode, and the pan pot can also work as a dual mono crossfader, making it suitable for blending two mono sources into a single mono sum.

All the parameters are voltage-controllable for creative mixing automation.

Mechanical mute, PFL, and Solo-in-Place complete the feature set suitable both for studio and live performances.

*The SC replaces the C as the primary single-channel CGM solution. The C module is now discontinued.

Notes: Variable Pole analogue filter based on Asteroid Op VCF Tech

Model: Millipede Variable Pole VCF
Analogue Filter, Can easily get Brutal tones.

What does this do?

This is an analogue filter that uses two modern equivalent ssm2164 IC's v2164 from cool audio to do it's magic. This particular filter however allows the user to vary the phase of each pole or filter cell. There are four filter cells total. This is similar to the Blue lantern Asteroid Operator Station VCF. The Asteroid Operator Station VCF has 8 Static filter out puts. Those 8 flavors were found by exploring the circuit found on the millipede vcf and internally installing the resistor ratio for that flavor.

On the millipede vcf you are allowed to find more exotic flavors yourself. Operation is easy. You first have all the poles counter clockwise and the three switches set to mute. This will have the filter as a dark Low pass filter. Then you turn on a pole using the switch and turn the know to hear the change. Pole 3 by default is always on, otherwise there would have been no sound if all poles were muted. Having all the poles set clockwise and active easily gets you into brutal sounding tones in a good way.

There is an on board diode limiter circuit to help tame really harsh tones. This is activated by switch.

The audio input has some gain, so you don't always have it fully clockwise. There is also a capacitor selector switch just like my other filters. This modifies the rez peak.

Dimensions
13 HP
32 mm deep

Current Draw
58 mA +12V
56 mA -12V

Depth: 2.5 inches

Notes: 4 stereo channel performance mixer with sidechain ducking

On-board compressor with external sidechain control voltage option to add proper dynamics to your mix

Stereo output for speakerphones or headphones with enough current to drive a wide range of headphones

available in 1U / 24HP version

Version 2 update (from original Cockpit):

Increased headroom

Improved sound quality

Daltonic friendly - the LEDs are blue/red instead of red/green

No TRRS jacks anymore

Available in Black and Classic Gold

New aluminum knobs on the black module version

Power consumption:
240 mA +12V
75 mA -12V
0 mA 5V

Dimensions:
6 HP
38 mm deep

Notes: Quantus Ampla is a compact four-channel VCA. But it's not just any VCA: with some unique normalizing, mixing, and CV options, and a bit of NE flair, you can use it for tonnes of stuff. From the top, each channel has two independent modes: Amplify, which gives you normal VCA response, and Attenuate, which makes the VCAs close instead of open in response to positive CV.

The CV inputs are circularly normalled, so you can easily create ducking effects over multiple voices, volume fades, and transitions, all with minimal patching. Plus, the outputs mix down, so it can be two two-channel mixers, a 3-channel mixer plus a VCA, a 4-channel mixer- mix and match to your heart's content. Did we mention it's DC-coupled? Yep, you can use it to process CV signals, too.

You can never have too many VCAs. Your Quantus Ampla is waiting for you.

Notes: A comprehensive solution for stereo signals in Eurorack, the Enhance 2 offers stereo and mid/side processing with tons of CV control. Balance, widen and sculpt frequency bands.

Supplier's Notes:
Moving from mono to stereo sound: a logical progression for any synthesist looking to expand their sonic palette. Making use of two audio channels, rather than just one, quite literally adds another dimension to the capabilities of a synthesiser.

Unfortunately, controlling stereo signals can be a challenge within a modular system. This realisation led to the development of Enhance 2: a convenient yet high-fidelity tool for stereo enhancement. It can be used to adjust balance, width and spectral content, while also opening up a world of mid/side processing; all under voltage control and in just 8 HP.

The primary stereo parameters are balance (moving the sound left or right) and width (making it narrower or wider). The balance circuit uses a true constant-power gain law, while the width stage allows for seamless transitions from pure mono to extra-wide stereo.

In addition, tone control is provided by a pair of unique, wide-ranging mid/side voltage controlled tilt filters with selectable corner frequency. These make 'cleaning up' a muddy-sounding mix straightforward, but also provide unique binaural effects when modulated.

Mid/side processing encodes the stereo signals into one containing only the mono material (mid), and another containing the differences between both channels (side). Apart from the internal tilt filters, mid/side outputs also enable external signal processing such as compression or reverberation. An integrated mid/side decoder returns the results back to standard stereo. And at all times, a LED bar phase meter ensures that phase correlation can be easily maintained.

Stereo field modulation, mid/side equalisation and beyond; Enhance 2 brings true analogue stereo control to the Eurorack world.

8 HP
+12: 70 mA, -12: 70 mA

Notes: 1U version of the excellent Golden Master, a surprisingly creative little output module which combines radio-style multi-band compression with brickwall limiting and mid-side stereo processing.

Supplier's Notes:
Golden Master is a multiband processor module in Eurorack format. Inspired from the studio mastering and radio loudness units from the 90's, this tool is a game changer for everyone who performs live with a Eurorack synthesizer.

The whole magic of Eurorack lies in its raw sound and simple analog mixes - processing through the Golden Master brings instant punch and sound pressure, as well as controlling the overall volume.

Features:

instantly improve your raw Eurorack mixes to sound balanced and powerful on stage or wherever you are
96 kHz 16 bit digital audio stereo processing
3-band compressor with intuitive adjustment and brickwall limiter
mid/side stereo field processing
Power consumption: 125mA at +12 V and 12mA at -12 V

Depth: 42mm

HP : 22

Notes: Endorphin.es add to the ranks of clever 1U format modules with this take on their Cockpit four-channel stereo mixer. Simple design including a CV/trig input for sidechain compression/ducking.

Supplier's Notes:
Endorphin.es Cockpit² is a 4-channel stereo mixer with side-chain ducking.

Key facts:

Increased headroom
Improved sound quality
the LEDs are blue/red instead of red/green (Daltonic friendly)
No TRRS jacks anymore
New knobs on the black module version
Power consumption: 37mA at +12 V and 23mA at -12 V

Depth: 41mm

HP : 24

Notes: The Five Amp is a throwback to SynthRotek's original 5A Power Supply with some upgrades. It uses a quality 12V power brick for the +12V power regulation instead of a +12V converter. The plus side of doing it this way is that whatever amperage the -12V and +5V rails are not using can be used by the +12V rail, which always draws the most of the three.

Five Amp comes in three different power configurations. It is recommend that you select an option based upon your -12V rail draw. For a rule of thumb, Red (with red LEDs) will power a single row of 84 or 104HP, Green will power two rows of 104HP, and Blue will power three to four rows of 104HP.

Notes: This is an exact hardware replica of the Mutable Instruments Clouds.

Notes: Ultra slim envelope generator with looping, ASR and AD modes

CV control over fall (decay / release)
Continuously variable shape over both slopes without stretching the slope's duration in time.
Low aliasing CV generation, 224 kHz sample rate.
1 v/oct input, bipolar and unipolar outputs, end of cycle output.
Audio rate oscillation in cycle mode allows you to utilize it as an oscillator.
Polarizer knob with additional VCA input scales the envelope and inverts it when CV goes to negative voltages, allowing for compact sidechain envelope solution without the need for external mixers / inverts / offset generators.
Slew limiter, S&H, T&H processing for external CV sources

Power consumption:
60 mA +12V
15 mA -12V
0 mA 5V

Dimensions:
4 HP
26 mm deep with power ribbon cable connected

Notes: Ultra slim envelope generator with looping, ASR and AD modes

CV control over fall (decay / release)
Continuously variable shape over both slopes without stretching the slope's duration in time.
Low aliasing CV generation, 224 kHz sample rate.
1 v/oct input, bipolar and unipolar outputs, end of cycle output.
Audio rate oscillation in cycle mode allows you to utilize it as an oscillator.
Polarizer knob with additional VCA input scales the envelope and inverts it when CV goes to negative voltages, allowing for compact sidechain envelope solution without the need for external mixers / inverts / offset generators.
Slew limiter, S&H, T&H processing for external CV sources

Power consumption:
60 mA +12V
15 mA -12V
0 mA 5V

Dimensions:
4 HP
26 mm deep with power ribbon cable connected

Notes: Two Of Cups - include samples in your live set. Two of them at once with a wide variety of CV-able features. Simply load one of 8 (!) banks each containing up to 24 samples for each of the two voices and off you go (unlock this feature with firmware 1.1!). Needless to say you can change the samples under CV and if needed - you can set up the trigger delay for each voice because that boy plays its sample so instantly and sample accurate with the with lightning speed. Breathe life and fresh sounds into your setup with a small footprint (6 HP) you would normally need to carry around a gazillion of gear to reproduce the sonic capabilities. Alternatively, use it the boring way and simply play drum one-shots off it.

2 voice intuitive sample player each containing 24 samples and organized in 8 banks

Zero-latency sample playback - directly from micro SD card

Factory sound-bank by Julia Bondar

On-board envelope generator decay control, pitch control with 1V/Oct input and sample selection control with meta cv input

Arbitrary sample rate: 8, 16 and 24 bit samples with 12 bit output bitrate

Power consumption:

125 mA +12V
20 mA -12V
0 mA 5V

Dimensions:

6 HP
30 mm deep

Notes: The window comparator is a very useful circuit building block that is common in general electronics, but rarely found in modular synths. While a regular comparator activates when the input signal voltage is higher than a threshold level, a window comparator checks if the voltage is between two levels (these form the 'window').

Compare 2 combines two such comparators and a logic section in 8 HP. The result is an advanced tool for extracting gates and pulses from analogue signals in Eurorack synths.

The detection windows are defined by the shift and size parameters, which can be varied using the knobs and CV inputs. Complementary gate outputs are available, with big three-colour LEDs showing each comparator's status.

All inputs are normalised from the left section to the right, but the two comparators can also be used completely independently. On the bottom, the outputs from both comparators are combined in various ways by the logic section, which also features LEDs.

You'll find a use for this truly multi-functional module in practically any patch, processing either CV or audio: complex rhythm generator, dual pulse width modulator, frequency multiplier/divider with PWM, digital ‘ring modulator’ with PWM, dynamic depth VCO synchronizer, voltage controlled swing, logic function array with adjustable thresholds... and many more applications waiting to be discovered!

Notes: While modular synthesisers are most often used as stand-alone instruments, they also present exciting opportunities for processing external signals. Anything from an electric guitar to an effects send on a studio mixing desk can benefit from the unique sonic capabilities of even a modest Eurorack system.

However, patching in an external source usually requires an adapter cable and plenty of clean gain to bring the signal to Eurorack level. If the signal source is balanced, a balanced input is required as well to provide the best possible interference rejection.

Receive 2 (or RX2 for short) provides a convenient all-in-one solution. It offers two universal external inputs, which accept both balanced or single-ended signals via XLR or 6.35 mm jack connectors.

The circuit incorporates low-impedance design practices, radio-frequency (RF) filtering and premium balanced receivers to provide transformer-like interconnect performance in a compact and affordable module. And thanks to the electrostatic discharge (ESD) protection, it’s rugged enough to survive the rigours of performing on the road.

The very clean integrated pre-amps feature variable gain, ranging from unity to +40 dB on each channel. As a result, Receive 2 can handle just about any signal source you may encounter, including electric instruments, piezoelectric pickups and many dynamic microphones.

Adjusting the gains is a breeze thanks to the dual peak-responding LED meters. A mix output is included as well, so external signals can be easily mixed directly in the module.

Notes: For decades, the voltage controlled slew limiter has been a staple of modular synthesisers. With its extreme versatility, it can be used to slew control voltages (CVs), create envelopes, as a low-frequency or audio oscillator and much more.

Today, Contour 1 brings a fresh approach to this classic circuit. It delivers much improved performance and control by incorporating modern design techniques.

At its most basic, a slew limiter slows down the rate of voltage change in a signal. On Contour 1, the rising and falling rates can be individually set using sliders and CV modulation.

The gate and trigger inputs allow the module to be used as a function generator: create snappy attack-release (AR) and attack-decay (AD) envelopes, with slope times ranging from 500 us to 30 seconds. The dedicated gate input makes it easy to generate +10 V envelopes from any signal source. Using the large tactile push button, AD envelopes can be manually triggered. A trigger will also reset the output voltage.

When set to loop mode, Contour 1 will continually re-trigger itself. In this mode, it fulfils the role of a variable-shape low-frequency oscillator (LFO) or temperature-stable voltage controlled oscillator (VCO) in the audio range.

Both the rising and falling slopes can be individually bent, from concave through linear to convex. While doing so, the deviation in slope time, and thus oscillation frequency, is kept to a minimum. Since the bend parameters are separately voltage controllable, boundless modulation possibilities present themselves.

Explore anything from shape-shifting envelopes to rich VCO timbres: Contour 1 will make you re-think what a slew limiter can do.

Dimensions
8 HP
30 mm deep

Current Draw
90 mA +12V
85 mA -12V

Notes: Transit has two stereo (dual mono) channel lanes of audio with an all-analogue signal path. Each stereo channel lane has its own input gain control, mute button and ducking input. The Ducking input on each channel operates like traditional sidechaining on a compressor where an input signal, CV or Trigger input (i.e. LFO, Clock, Gate) modulates the gain reduction of the audio.

Transit offers a main stereo output controlled by the master volume control knob and an independent 3.5mm headphone output controlled by its own headphone level control knob.

Digitally controlled LEDs for each stereo channel lane indicate level via white, blue and pink illumination while engaging mutes illuminates the LEDs with the color red. Master and headphone levels also have their own LEDS for level indication using the same color scheme of illumination.

All in all, Transit is a rather full features compact 6hp dual stereo channel lane eurorack formatted mixer that offers easy signal mixing, gain staging, ducking, and performance-oriented mutes. Transit is just as at home in a small eurorack system as one Transit or several would be in a larger system.

Tech specs

Width: 6HP
Depth: 30mm
Power: 50mA +12V, 50mA -12V

Notes: Xer Dualis is a compact analogue four-channel stereo mixer. Each channel has left and right inputs, a level control, and a mute.

Want to use mono signals? No problem! The left inputs normal to the right ones. On the stereo pair output, XD features a simple meter and a clip indicator to keep your mix clean. Xer Dualis is a compact and performable choice whether you need a submixer for a large system or an easy way to mix all the elements of a portable case together.

Notes: The Erica Synths Envelope Generator 2 is a re-triggerable, looping envelope generator with some unconventional features that are very useful for experimental setups. What sets the Black EG2 apart from other envelope generators is its optional GATE LENGTH setting, which allows for generating full ADSR envelopes even if a short trigger is used at the input. Likewise, in LOOP mode, the module outputs a full ADSR envelope instead of a classical AD envelope. The gate length is both manual and CV controlled, which allows for using this envelope generator in compact modular setups controlled by trigger sequencers only.

SPECS:

Gate input level 3...10V
Envelope amplitude 0...10V
Attack time 0...7,4"
Decay time 0...19"
Sustain level 0...10V
Release time 0...17"
Gate length 0...3,7"
Panel width 8HP
Module depth 25mm
Power consumption 29mA@+12V, 33mA@-12V

LOOP/SINGLE

Select between SINGLE SHOT or LOOP modes. When the internal gate is o , the rise and fall times are set via the A and R knobs. When the internal gate is on, all knobs have an e ect on the envelope shape.

The LED gives visual feedback on the envelope state.
GATE ON
Engage the internal gate and you have a full ADSR envelope in loop mode and with a trigger applied to the trigger input in single mode.

G. LENGTH

Set the internal gate length manually

LENGTH CV

This is the internal gate length CV input.

The CV is added to the gate length potentiometer setting

GATE

This is the GATE input

A / D / S / R

These knobs adjust envelope stage times and sustain level

TRIGGER

This is the TRIGGER input. You can retrigger the envelope and start the attack stage again, even if the gate is still high (see Figure 1).

If you wish to use the envelope generator with an internal gate, patch the incoming trigger signal here. The internal gate is linked to the trigger input, not the gate input.

EG OUT

This is the envelope generator output.