Passive interface lets you connect instrument, line, or speaker level signals to a mixer or other balanced input thru an audio isolation transformer
Notes: The Zdirect is a high quality totally passive interface that lets you connect instrument, line, or speaker level signals to a mixer or other balanced input thru a high performance audio isolation transformer. The high impedance single-ended 1/4" input is converted by the transformer into an isolated balanced low impedance signal source. The Zdirect's audio transformer has an extremely flat and wide frequency response and can handle high signal levels while still maintaining an isolated balanced low impedance output. This gives the Zdirect a very clean and neutral sound with a wide variety of signal sources and over long signal runs in high noise environments.
The input attenuator switches allow for a wide range of signal levels and the input thru jack allows for tapping off of your signal chain. The ground lift switch lets you totally separate the input and output signal grounds, when appropriate, to isolate 2 systems, thereby reducing hum and ground-loop noise.
What further sets the Zdirect apart from other DI boxes are its extended features and versatility. ART have added a switchable low pass filter that cuts out all very high frequency interference. This Bessel filter on the output is placed out of the audio range and is primarily intended to reduce radio frequency interference before it gets into the main system. The filter is also very effective in reducing any digital computer noise artifacts when using the Zdirect as an interface between a computer-based audio workstation and your monitors. The phase invert switch, while not normally included with your run of the mill DI box, has been added to allow you to switch signal polarity right at the source. This feature is especially handy when you are combining a direct tap with a microphone feed in the mix.
The compact black anodized all aluminum case and it's passive design allow the Zdirect to provide years of trouble free service in Live Sound, Permanent/Fixed Install, DJ, and virtually any PA application. It's full feature set, rugged construction, and high-end specifications make the Zdirect the obvious choice.
Notes: With the DI100, you can rest assured that your sound source will reach the console balanced and noise free. Behringer's take on the all important active DI box gives you functionality, durability and incredible sound at a remarkable price.
Plug into the DI100's balanced 1/4" TRS or XLR input, then send a signal to your console via the balanced XLR output. You can even plug your guitar or bass amp's speaker output into the DI100, which can handle ratings of up to 3,000 Watts and still deliver a perfect signal. It also features a 1/4" link jack to send your signal to an on stage amplifier.
The DI100 also has a switchable attenuation pad, allowing input levels of up to +50dB. There is also a ground lift switch to eliminate noise associated with ground loops. The DI100 also features Behringer's renowned OT-1 output transformer.
Notes: The ULTRA-DI PRO DI4000 gives you 4 first-class DI channels in a single rack space. Each channel is equipped with two Inputs (XLR and 14" TRS), a balanced XLR Output - and a 14" Link output to connect to your amp or monitor console. Plus, the DI4000 is designed to accommodate virtually any input signal, up to 40 dB of switchable input attenuation and up to 20 dB of gain, while our highly acclaimed OT-1 output transformers ensure pristine and powerful output.
Direct Injection (DI) boxes make it possible to connect guitars, basses and keyboards (as well as other line-level devices) to audio mixers and recorders. The DI4000 takes the DI box to the next level with a special 8 kHz High-Cut filter per channel for guitar applications, along with a Phase Reverse switch for optimal signal alignment. Additionally, our DI4000 active DI features "buffered" inputs that respect your source signal much better than passive DI boxes can - outputting optimally-balanced, extremely low-impedance (600 O) signals that are far less susceptible to noise and RF Interference (RFI).
The DI4000 does much more than just "bass guitar in, mic-level signal out". It really is a highly versatile input-signal toolkit. Here are just two advantages the DI4000 has over standard DI boxes: Maybe you'd like to connect your guitar amp's speaker output to your mixer? Not a problem, the DI4000 features two -20 dB attenuation switches per channel, allowing you to connect to speaker outputs rated up to 3,000 Watts - and convert them to balanced XLR outs! Weak incoming signal? The DI4000 has a +20 dB switch, which really comes in handy for boosting low-level input signals to balanced signals with real power and rock-solid impact. Worried about fluctuating voltages in the venue? The DI 4000 is equipped with an internal switch-mode power supply that ranges from 100 to 240 V and automatically adapts to mains voltages wherever you go. Of course, the DI4000 provides a Link output for easy connection to other equipment, such as your onstage amplifiers and monitor consoles. Servo-balanced performance guarantees ultra-flat frequency response - and the gold-plated XLR output connectors provide reliable, low-noise operation. Per channel ground-lift switches eliminate ground-loop hum issues. The DI4000 does everything a standalone DI can do, and much more - times four!
Notes: The Behringer Ultra DI DI400P is a passive DI (Direct Injection) box for connecting a guitar, bass or keyboard directly to your mixer. With the DI400P as your go between, impedance matching problems become a thing of the past, and long cable runs will not sacrifice all of your precious tone.
With its parallel 1/4" in and out jacks, the DI400P allows you to plug in your instrument and send the same signal to your onstage amplifier, while the XLR Output sends a balanced signal to your mixer. A ground lift switch eliminates hum associated with ground loops and our high performance transformer provides the ultimate in signal integrity.
The Ultra DI DI400P is compact and we house it in a tough, road ready metal case. This means the DI box will give you great sound gig after gig, session after session. And thanks to its low price, you can afford to outfit the entire band!
Notes: Passive DI box for converting high impedance instrument outputs to low impedance line signals for feeding directly into a mixing console. Equipped with 3 pad settings, RF/mains filter and selector for ground lift with or without filter.
Ground float option for ground lift with RF/mains filter
Ground lift option isolates signal ground without filter
3 pad settings for level matching
Notes: A Reamping-Box is mainly used in studios. It allows you to play back a recorded guitar signal and send it to a guitar amp, where it can again be taken and recorded by the microphone. This way, the recording engineer can experiment with the sound of an instrument and different amplifiers at his leisure.
The DACCAPO box ensures optimal impedance matching and eliminates ground loop hum through the use of a transformer. The signal level to the amplifier can be adjusted with a volume control.